Rockford Fosgate P560 User manual

P560
Owner’s Guide
5.1 Speaker System

1

2

3

4

5
Thank you for purchasing Rockford Fosgate P560 5.1 Powered Speaker System.
We hope it exceeds your expectations in sound quality. The P560 is designed to deliver superior
sound with 5.1 theater quality sound for your movies, games, and music. We offer various methods
of connectivity including Bluetooth, Optical, RCA, AUX, and the latest in gaming sound cards. So
whatever audio player you have (i.e. mobile phone, gaming console, tablet, computer, TV, etc.),
the P560 will be your go to system.
Dolby Digital is the universal standard for 5.1
digital sound. Onboard 5.1 digital decoding
enables detailed surround sound—from the roar
of the crowd to the footsteps right behind you—
in your Dolby Digital soundtracks.
Dolby®Digital
CAUTION
• Do not plug the power supply in until all connections are made.
eo ampliers, space heaters,
• Keep speakers away from sources of extreme heat such as ster
stoves, heat vents, etc.
• Do not wipe any part of the system with cleaning solvents such as furniture wax, bleach,
benzene, acetone, or ammonia.
5 satellite speakers
1
Subwoofer
2
Control console
3
IR remote
12" aux cable
4
5
3 x 3.5mm cables
6
RCA cable
7
2 x AAA Batteries
8
Owner’s guide with connection diagram
9
10
10
T-560
Owner’s Guide
5.1
Speaker System
8
57
2
3
6
4
1
1
9
Your system includes:
5 sets of connection wire (7.6m / 25ft x 2 ; 4.6m / 15ft x 3)

6
Speaker Preparation
For speaker preparation, we suggest you arrange your system similar to the diagram shown below.
• Front Satellite Speakers — Place the two front satellite speakers on opposite sides of your
TV or computer monitor. Locate them equal distance from each other and adjust the angle so
the speakers are facing you.
• Rear Satellite Speakers — Place the two rear satellite speakers behind you (with similar distance
apart as the front speakers). Then adjust the angle to face you.
• Center Satellite Speaker — Place the center satellite speaker above or below your TV or
computer monitor (Caution: do not put center satellite directly on top of TV or computer monitor).
• Subwoofer – You can put the subwoofer anywhere in your room. To get the strongest bass, put
your subwoofer near a wall, corner, or underneath a desk. Make sure that nothing is closer than
20cm to the driver or port tube because it will affect the sound. It is important to allow for
enough ventilation around the subwoofer, we recommend 20cm .
• Control Console – Place the console where it is easy to reach and make sure the IR receiver
window is not blocked.
Subwoofer
FL
RL RR
FR
C
Control Console

7
Subwoofer back panel
1. Control Console connection port
2. Red/White (RCA)
3. Optical in (Digital input)
4. PC Sound card connections
5. Satellite output connection ports
6. AC power cord
LINE IN
OPTICAL IN
FL / FR
RL / RR
C / SW
AC Power
CONSOLE
FL
FR
RL
RR
C
1
2
3
4
5
6
Speaker Connection

8
Control Console
1. Input selection: Use this button to switch between your audio source. (Optical, Line in, PC
in, AUX in, Bluetooth)
2. Effect: Use this button to switch between 2.1 output or 5.1 output.
3. Bass: Press this button to adjust bass channel; when the BASS LED is on, you can adjust
bass volume by rotating the knob.
4. Power: Master power on/off
5. Mute: Mute the entire system
6. Volume / level adjustment knob: Adjust master volume
7. IR remote sensor
8. Input selection indicator
9. Speaker output indicator
10. Decode indicator: LED will be on when Dolby Digital signal is detected.
11. Sound effect indicator: Either 2.1 output mode or 5.1 output mode.
12. Bass indicator: When LED is on you can adjust bass level.
13. Headphone output jack
14. AUX input jack
Front Back
POWER MUT E
BASS
EFFECT
INPUT
BLUETOOTH
AU X IN
LI NE IN
OPTICAL
FL
FR
C
R
L
PC I N
RR
SU B
BASS
2.1
3D
1
2
3
4 5
6
7
8
9
10
12
11
13 14
DECODE

9
IR Remote Control
1. Input selection: Use this button to switch between your audio source.
(Optical, Line in, PC in, AUX in, Bluetooth)
2. Effect: Use this button to switch between 2.1 output or 5.1 output.
3. Play: During Bluetooth connection, press this button to play or pause. Press and hold for 5
seconds to enter Bluetooth pairing mode.
4. Master volume: Up/Down
5. Mute the entire system
6. Master Power: On/Off
Power On
•Plug the subwoofer power cable into an electrical outlet.
•Press Power on the Control Console to power on the speaker system.
Caution: Make sure all connections are made rst.
1
2
3
4
5
6
+
-
Battery
+
-
Battery
AAA AAA

10
Audio Input Selection
PC Sound Card Input Connection
•There are three 3.5mm input jacks for true 5.1 PC Sound card on the rear panel of the
subwoofer. Please check your sound card manual for the proper connections.
•Press the “INPUT” button to switch the input until the “PC IN” LED lights up.
Line In Input Connection
•Making connection with your speaker to any AV system, game console, etc. using the
RCA input on the rear panel of subwoofer.
•Press the “INPUT” button to switch the input until the “LINE IN” LED lights up.
Optical Input Connection
•Use an optical cable to connect your device to the optical port on the rear panel of the
subwoofer. (Optical cable is not included)
•Press the “INPUT” button to switch the input until the “OPTICAL” LED lights up.
AUX IN Input Connection
• You can connect any laptop, tablet, smartphone, MP3 player, etc. by using a 3.5mm AUX
cable and plugging it into the AUX jack on the rear side of the control console.
•Press the “INPUT” button to switch the input until the “AUX IN” LED lights up.
Adjust Volume
Rotate the volume knob to adjust the entire system’s volume. The LED bar will turn into a volume
status
bar when you start to rotate the knob. It will resume the display status after adjustments are
made.
Adjust Bass Volume
Press “BASS” button and the “BASS” LED will turn on. The LED bar will turn into bass level status
bar. Adjust the bass volume by rotating the knob. It will resume the display status after adjustments
are made.
Bluetooth Input Connection
•Press the “INPUT” button to switch the input until the “BLUETOOTH” LED lights up.
•First time pairing; the P560 will automatically go into pairing mode.
•Go to your Bluetooth device and select the device named “P560”.
•If the system is turned off, it will automatically search for the latest connected device when
turned back on. If the device cannot be found, it will enter into pairing mode.
• If you want to pair another new device, you can press and hold the “PLAY” button for 5 seconds
on the IR remote control to trigger the system into pairing mode.

11
Still can’t connect
1. Be sure to check your room environment. Today’s Bluetooth technology has a designed limit of approximately 30 feet, line
of sight. This generally means your best result will be limiting your source device and speakers to the same room. Extremely
large rooms, or rooms with lots of wireless electronics, wi- routers, radio transmitters, etc. may affect your ability to pair.
2. Check to see if any other devices are already connected to the P560. The speakers can only pair with one device at a time.
If you need to unpair, choose “Forget this device” from your source. Then follow Bluetooth Input Connections on page #10.
3. Check the battery life on your source device and charge if necessary. Most devices operate best when charged above 20%
minimum battery level.
Can’t connect for the first time
1. Turn off the speaker system by pressing the POWER button.
2. Check your Bluetooth source device and make sure you have found the section that allows you to see nearby Bluetooth
products. If you see the P560 on the list, but cannot connect, you may need to search again. To start fresh with your
Bluetooth device, select “Forget this device” and remove the P560 from the list. You may need to turn off the Bluetooth
function on your device to fully clear your list.
3. Turn on the speaker system again by pressing the POWER button and select Bluetooth as input by pressing the INPUT
button until BLUETOOTH LED is on; the LED will be blinking rapidly showing that the speaker system is in pairing mode.
4. Return to your source device and re-enable the Bluetooth function. Look for the P560 speakers to show back up on the list.
5. Select the device on the list and the BLUETOOTH LED will become solid if it is connected successfully.
Can’t connect when returning
1. If the P560 does not automatically connect back with your Bluetooth-enabled device, you may need to physically go into
your device’s Bluetooth settings and select “P560” to reconnect.
2. If the above step does not work, see steps 1-5 in the “Can’t connect for the rst time” section above.
Audio is choppy, has erratic static, or keeps disconnecting
1. Be sure to check the room environment. Today’s Bluetooth technology has a designed limit of approximately 30 feet, line of
sight. This generally means your best results will be limiting your source device and speakers to the same room. Extremely
large rooms, or rooms with a lot of wireless electronics, routers, etc. may affect the quality of sound, connection, or
connection consistency.
2. Check for obstructions, walls, or other objects that might impede the Bluetooth signal.
3. Try returning the source device to a closer proximity to your speakers.
ADDITIONAL SUPPORT
The latest updated video tutorials, FAQ, and product feature specications are available online 24/7 at
http://cyberacoustics.com/P560 or Technical support is available at 360-883-0333, M-F 8am to 5pm PST.
TROUBLE SHOOTING
BLUETOOTH TROUBLE SHOOTING
Power button is not turned on. Press the power button back and forth
and check for the blue LED indicator light to come on.
Verify the AC power cord is plugged into the wall outlet.
Check if the wall outlet or power strip you are using is actually getting
power, i.e. not a switched outlet.
Speaker Does Not Produce
Sound
SYMPTOM
Speaker System Will
Not Power
SOLUTION
Verify the speaker is getting power. Check the steps above.
Verify that all cables are plugged into the correct jacks or that the
Bluetooth is paired correctly.
Turn the speaker volume down by 25% or 50%.
Adjust the bass volume control to test for maximum and minimum
output. You may also need to move the subwoofer either closer or
farther away from a wall or corner to affect the sound performance.
A djust the sound source’s master volume control by balancing the
volume until it’s centered.
Sound Is Distorted

12
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure
condition without restriction.
Performance Specifications
A: Watts: 530W RMS
Satellites – 75W watts/ch x 5 @ 8 ohm – 10% THD
Subwoofer – 155Watts @ 4 ohm – 10% THD
B:
Speakers size:
Satellites – 4.3” (W) x 3.7” (D) x 7.0” (H)
Center Satellites – 6.5” (W) x 3.7” (D) x 4.0” (H)
Subwoofer – 11” (W) x 13” (D) x 11.5” (H)
C:
Drivers size:
3” dynamic satellite drivers
8” poly-carbon high excursion sub
D:
Frequency response: 28Hz – 20KHz
Wall Mounting
You can mount your satellite speakers with the appropriate hardware (not included).
• Do not mount the speakers on thin plywood or on a wall with a soft surface material. The speakers may fall, possibly
damaging the speakers or causing personal injury.
• Do not affix the speakers to a wall using nails, adhesives, or unstable hardware. Long-term use and vibration may cause
the speakers to fall.
• To avoid accidents resulting from tripping over loose speaker cables, affix the cables to the wall and floor.
• Mount the speakers in a wall location that will be less likely to result in injury to an individual’s head or property damage.
Warranty
For warranty information and registration, please go to www.cyberacoustics.com/rockford

P560
Guide d'utilisation
Système d'enceintes 5.1

13
Merci d'avoir choisi ce système d'enceintes 5.1 Dolby Rockford Fosgate P560.
Nous espérons qu'il répondra à vos exigences en matière de qualité de son. Le P560 est conçu pour
nombreuses, y compris Bluetooth, optique, RCA, AUX et les dernières cartes son pour jeux vidéo.
Donc, quel que soit le type de lecteur audio (ex. téléphone mobile, console de jeux, tablette,
ordinateur, téléviseur etc.), le P560 sera votre système de choix.
Dolby Digital est le standard universel
pour le son numérique 5.1. Le décodage 5.1
embarqué apporte à vos bandes son Dolby
Digital un son "surround" à haute précision—
de la clameur de la foule au bruit de pas juste
derrière vous.
Dolby®Digital
ATTENTION
• Ne mettez pas le système sous tension tant que toutes les connexions ne sont pas réalisées.
• Tenez les enceintes à l'écart de toute source de chaleur extrême telle qu'amplis stéréo,
chauffages, poêles, grilles de ventilation etc.
• Ne nettoyez aucune partie du système à l'aide de solvants tels que cirage à meubles, javel,
benzène, acétone ou ammoniaque
5 enceintes satellites
1
Subwoofer
2
Télécommande IR
3
IR remote
Cordon AUX
4
5
3 x cordons 3,5 mm
6
Cordon RCA
7
2 x piles AAA
8
Guide d'utilisation avec schéma de connexion
9
10
10
T-560
Owner’s Guide
5.1
Speaker System
8
57
2
3
6
4
1
1
9
Votre système comprend :
5 jeux de câbles de connexion (7.6m / 25ft x 2 ; 4.6m / 15ft x 3)
Fabriqué sous licence Dolby Laboratories.
Dolby et le sigle double-D sont des marques commerciales de Dolby Laboratories.

14
Disposition des enceintes
Pour la disposition des enceintes, nous vous conseillons de suivre le schéma ci-dessous.
• Enceintes satellites avant — Placez les deux enceintes satellites de part et d'autre de votre
téléviseur ou écran d'ordinateur. Placez-les à distance égale et orientez-les vers vous à un angle.
• Enceintes satellites arrière — Placez les deux enceintes satellites arrières derrière vous, séparées
de la même distance que les enceintes avant. Orientez-les de la même façon.
• Enceinte satellite centrale — Placez l'enceinte satellite centrale au-dessus ou en-dessous de votre
téléviseur ou écran. (Attention: ne placez pas l'enceinte satellite centrale directement sur le
téléviseur ou l'écran).
• Subwoofer –Vous pouvez placer le subwoofer où vous voulez dans la pièce. Pour obtenir les
meilleures graves, placez le subwoofer près d'un mur, dans un angle ou sous un bureau. Vériez
de n'avoir aucun objet à moins de 20 cm du haut-parleur ou du port au risque d'altérer le son. Il
recommandons un espace de 20 cm.
• Console de commande – Placez la console à un endroit convenable et vériez de ne pas obstruer
la fenêtre du récepteur IR.
Subwoofer
AvG
ArG ArD
AvD
C
Console de commande

15
Face arrière du subwoofer
1. Port de connexion de la console de commande
2. Prises RCA rouge/blanc
3. Entrée optique (entrée numérique)
4. Prises de connexion pour carte son PC
5. Ports de connexion pour les enceintes satellites
6. Cordon d'alimentation AC
LINE IN
OPTICAL IN
FL / FR
RL / RR
C / SW
AC Power
CONSOLE
FL
FR
RL
RR
C
1
2
3
4
5
6
Branchement des enceintes

16
Console de commande
1. Sélection d'entrée : Utilisez ce bouton pour changer de source audio (optique, entrée ligne
PC ou AUX, Bluetooth)
2. Effet : Utilisez ce bouton pour basculer entre sortie 2.1 et sortie 5.1.
3. Graves : Appuyez sur ce bouton pour régler le canal des graves ; lorsque le LED BASS est
allumé, vous pouvez régler le volume des graves en tournant le bouton
4. Marche/arrêt : Bouton principal de marche/arrêt
5. Mute : Éteindre complètement le son du système
6. Bouton de réglage du volume : Régler globalement le volume
7. Capteur IR de la télécommande
8. Voyant de sélection d'entrée
9. Voyant de sortie enceinte
10.Voyant de décodage: Le LED indique la détection d'un signal Dolby Digital
11.Voyant d'effet : Sortie 2.1 ou 5.1
12.Voyant des graves : Lorsque le LED est allumé, vous pouvez régler le niveau des graves.
13.Prise de sortie casque
14.Prise d'entrée AUX
Face avant Face arrière
POWE R MUTE
BASS
EFFECT
INPUT
BL UET OOT H
AU X IN
LI NE IN
OPTICAL
FL
FR
C
R
L
PC I N
RR
SU B
BASS
2.1
3D
1
2
3
4 5
6
7
8
9
10
12
11
13 14
DECODE

17
Télécommande IR
1. Sélection d'entrée : Utilisez cette touche pour changer de source audio (optique, entrée ligne
ou PC ou AUX, Bluetooth)
2. Effet: Utilisez cette touche pour basculer entre sortie 2.1 et sortie 5.1.
3. Lecture: Lors d'une connexion par Bluetooth, appuyez sur cette touche pour lire ou mettre en
pause. Maintenez enfoncée la touche pour entrer en mode jumelage Bluetooth.
4. Commande principale du volume : augmenter/diminuer
5. "Mute" : couper le son du système.
6. Commande principale marche/arrêt.
Mise sous tension
• Branchez le cordon d'alimentation du subwoofer sur une prise secteur.
• Appuyez sur le bouton marche/arrêt de la console de commande pour allumer le système.
Attention : Vériez d'avoir effectué toutes les connexions au préalable.
1
2
3
4
5
6
+
-
+
-
AAA pile AAA pile

18
Sélection de la source audio
Connexion depuis une carte son PC
• La face arrière du subwoofer comporte trois prises 3,5 mm pour connecter une carte son
véritable 5.1. Veuillez consulter le manuel de votre carte son pour les instructions de connexion.
• Appuyez sur le bouton INPUT jusqu’à ce que le voyant LED PC IN s’allume.
Connexion via l’entrée ligne
• Connectez votre système d’enceintes avec n’importe quel système AV system, console de jeux
etc. à l’aide des prises RCA sur la face arrière du subwoofer.
• Appuyez sur le bouton INPUT jusqu’à ce que le voyant LED LINE IN s’allume.
Connexion par câble optique
• À l’aide d’un câble optique, connectez votre périphérique à la prise optique sur la face arrière du
subwoofer (câble optique non inclus).
• Appuyez sur le bouton INPUT jusqu’à ce que le voyant LED OPTICAL s’allume.
Connexion via l’entrée AUX
• À l’aide d’un câble AUX 3,5 mm, connectez n’importe quel ordinateur portable, tablette,
smartphone, lecteur MP3 etc. à la prise AUX sur la face arrière de la console de commande.
• Appuyez sur le bouton INPUT jusqu’à ce que le voyant LED AUX IN s’allume.
Réglage du volume son
Tournez le bouton du volume pour régler le volume son du système. La barre LED se transforme en
témoin de volume lorsque vous commencez à tourner le bouton, puis réafche l’état du système
une fois le réglage terminé.
Réglage du niveau des graves
Appuyez sur le bouton BASS : le voyant LED BASS s’allume. La barre LED se transforme en témoin
de niveau des graves. Réglez le niveau des graves en tournant le bouton. La barre réafche l’état du
système une fois le réglage terminé.
Connexion par Bluetooth
• Appuyez sur le bouton INPUT jusqu’à ce que le voyant LED Bluetooth s’allume.
• Premier jumelage : le P560 se met automatiquement en mode jumelage.
• Sur votre appareil Bluetooth, sélectionnez le périphérique “P560”.
• Lorsque vous rallumez le système, il recherche automatiquement le dernier appareil Bluetooth
connecté. Si cet appareil est introuvable, il passe automatiquement en mode jumelage.
• Si vous souhaitez jumeler un autre appareil Bluetooth, appuyez sur la touche PLAY de la
télécommande IR pendant 5 secondes pour lancer le mode jumelage.