Rocktron CLASSIC WAH PEDAL User manual

Copyright © 2007 GHS Corporation
All Rights Reserved.
Your Classic Wah
pedal has been tested and complies with the following
Standards and Directives as set forth by the European Union:
Council Directive(s):
89/336/EEC Electromagnetic Compatibility
Standard(s):
EN55013, EN50082-1
This means that this product has been designed to meet stringent guide-
lines on how much RF energy it can emit, and that it should be immune
from other sources of interference when properly used. Improper use of this
equipment could result in increased RF emissions, which may or may not
interfere with other electronic products.
To insure against this possibility, always use good shielded cables for all
audio input and output connections. This will help insure compliance with
the Directive(s).
For more information about other Rocktron products, please see your local
dealer or one of our importers closest to you (listed on the Rocktron website
- www.rocktron.com).
Precautions
Read all instructions contained in this manual.
Keep these instructions
Heed all warnings
Follow all instructions.
Do not use this apparatus near water.
Clean with dry cloth

Do not block any ventilation openings (if applicable). Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including amplifi ers) that produce heat.
This product is not equipped with a plug or cable. This pedal runs on a
9 Volt Battery, if a 9-Volt DC adapter is the used please follow adapter
manufacturer’s operation instructions.
Only used attachments/acces
sories specifi ed by the manufacturer.
Do not use this product with any case, stand tripod, bracket or table that
is not specifi ed by the manufacturer. Insure that the case, stand, tripod,
bracket etc. is properly adjusted and setup (follow all instructions). Extra
care and caution should be taken to avoid tip over and injury.
Unplug this apparatus during lightening storms or when unused during long
periods of time.
Refer all service to qualifi ed service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power supply or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus
or if the apparatus has been exposed to rain or moisture, does not operate
normally or has been dropped.
DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. QUALIFIED PER-
SONNEL SHOULD SERVICE THIS EQUIPMENT ONLY. DO NOT MAKE
ANY INTERNAL ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT
AT ANY TIME OR TAMPER WITH INTERNAL ELECTRONIC COMPO-
NENTS AT ANY TIME. FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY VOID THE WARRANTY OF THIS EQUIPMENT AS WELL AS CAUS-
ING A SHOCK HAZARD.
OPERATING TEMPERATURE
Do not expose this unit to excessive heat. This unit is designed to oper-
ate between 32° F and 104° F (
0
°
and 40° C). This unit may not function
properly under extreme temperatures.
Precautions Continued....

Introduction
Congratulations on your purchase of the Rocktron
Classic Wah.
The Rocktron Classic Wah is a vintage style wah
with classic tone. Solid construction makes the
Classic Wah stage ready.
The easy access battery compartment will make
changing batteries during a gig a breeze. And, we
have incorporated an adjustable rocker tension
screw that will allow you to adjust the pedal action
for a lighter or heavier “touch”.

Connection

Connection when using with other
stomp boxes or effects:

Controls and Descriptions:

ROCK
ER FOOTPEDAL
- Place your foot on the rocker foot-
pedal and rock it up and down (toe to heel - heel to toe) to work
the “ wah” effect.
Wah ON/OFF Switch
- is located under the toe of the rocker
footpedal. To activate the “wah” press down slightly harder on
the toe of the rocker pedal until the switch is activated. The
same process is to be applied to turn off the wah effect. The
wah effect will be on when the red LED is lit (see point 7).
INPUT Jack
- using a standard guitar cable - plug your guitar
INPUT Jack - using a standard guitar cable - plug your guitar INPUT Jack
into this jack.
PEDAL ROCKER TENSION ADJUSTMENT
- This screw will
allow you to adjust the “action” of the pedal to suit your taste
with the included allen wrench. If you would like a tighter or
heavier movement of the pedal using an allen wrench turn the
screw clockwise. This will increase the torque and tension on
the rocker pedal. If you would like a smoother or softer pedal
movement turn the allen screw counter-clockwise. This will
loosen the tension on the pedal pivot point.
9-VOLT ADAPTER INPUT
- This receptacle requires a 9V DC
adapter (not included) with a 2.1mm coax plug to provide pow-
er to the unit. Please consider using the Rocktron DC OnTap
adapter (sold separately) available from your Rocktron dealer.
Note: If an adapter other than the Rocktron DC OnTap adapter is used, it needs to be a 9V DC
fi ltered audio grade type with a current rating of 100ma or greater . The plug is a 2.1mm Coax
jack (Tip is Negative and Sleeve is Positive). Please follow all instructions that appear on the
bottom of the Classic Wah.
1
2
3
4
5
Controls and Function Descriptions

Specifi cations
Maximum Input
Input Impedance
Output Impedance
Wah frequency Range
Current Consumption
Power Requirements
+10dBu
1M ohm
1K ohm
400Hz (Heel Down) to 2KHz (Toe
Down)
20ma or greater
9VDC >=100ma
6
7
8
Controls and Function Descriptions - Cont.
OUTPUT Jack
- using a standard guitar cable, plug this out-
OUTPUT Jack - using a standard guitar cable, plug this out-OUTPUT Jack
put into the next effect in your effect chain or directly into the
input of your guitar amplifi er.
WAH ON LED
- The red LED will be lit when the “wah” effect
is activated. To activate the wah - see point 2. The red LED
will not be lit when the wah is bypassed.
9-VOLT BATTERY COMPARTMENT
- to access pull on
small tab labeled “OPEN”. Replace with a new 9-Volt battery.
Always remember to unplug your guitar cords from the pedal
to conserve battery life. Some battery drain may take place
when unit is plugged in (even if the unit is bypassed).
The Classic Wah (as with all Wah Wah pedals) are normally put in
the beginning of your signal chain. Although, you may place your
wah at any place in your signal chain, it usually sounds best at the
beginning - directly from your guitar (or bass).
Hints and Tips