Rocktron Reaction Compressor User manual

May be covered by one or more of the following: U.S. Patents #4538297, 4647876, 4696044, 4745309, 4881047,
4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617.
Other patents pending. Foreign patents pending.
Reaction Compressor
Instruction Manual

Your Reaction Compressor™pedal has been tested and complies with the following Stan-
dards and Directives as set forth by the European Union:
Council Directive(s): 89/336/EEC Electromagnetic
Compatibility
Standard(s): EN55013, EN50082-1
This means that this product has been designed to meet stringent guidelines on how much
RF energy it can emit, and that it should be immune from other sources of interference when
properly used. Improper use of this equipment could result in increased RF emissions, which
may or may not interfere with other electronic products.
To insure against this possibility, always use good shielded cables for all audio input and
output connections. This will help insure compliance with the Directive(s).
For more information about other Rocktron products, please see your local dealer or one of
our importers closest to you (listed on the Rocktron website
(www.rocktron.com).
Read all instructions contained in this manual.
Keep these instructions
Heed all warnings
Follow all instructions.
Do not use this apparatus near water.
Clean with dry cloth
Copyright © 2009 GHS Corporation
All Rights Reserved.
Compliance

Do not block any ventilation openings (if applicable). Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves or other ap-
paratus (including ampliers) that produce heat.
This product is not equipped with a plug or cable. This pedal runs on a 9 Volt Battery, if a
9Volt DC adapter is the used please follow adapter manufacturer’s operation instructions.
Only used attachments/accessories specied by the manufacturer.
Do not use this product with any case, stand tripod, bracket or table that is not specied by
the manufacturer. Insure that the case, stand, tripod, bracket etc. is properly adjusted and
setup (follow all instructions). Extra care and caution should be taken to avoid tip over
and injury.
Unplug this apparatus during lightening storms or when unused during long periods of time.
Refer all service to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus or if the apparatus has been exposed to rain
or moisture, does not operate normally or has been dropped.
DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. QUALIFIED PERSONNEL
SHOULD SERVICE THIS EQUIPMENT ONLY. DO NOT MAKE ANY INTERNAL
ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT AT ANY TIME OR TAMPER
WITH INTERNAL ELECTRONIC COMPONENTS AT ANY TIME. FAILURE TO FOL-
LOW THESE INSTRUCTIONS MAY VOID THE WARRANTY OF THIS EQUIPMENT
AS WELL AS CAUSING A SHOCK HAZARD.
OPERATING TEMPERATURE
Do not expose this unit to excessive heat. This unit is designed to operate between 32 F and
104 F (0 C and 40 C). This unit may not function properly under extreme temperatures.
Precautions

Introduction
Compressors are one of the best tools in a guitar player’s
tool box, and the Reaction Compressor fullls all the
requirements for outstanding compression. Professional
players use a compressor like a secret weapon to get
accomplish many things, including adding more sustain
to any guitar without adding distortion, dening every
note in a chord while letting it ring out, creating in your
face solos, and much more.
Rocktron’s Reaction Series pedals are built into a rugged
metal slim form factor chassis, taking up as little space as
possible on your pedalboard. The Reaction Compressor
is a TRUE BYPASS pedal: when you turn it off…it is out
of your signal path!
Control knobs for the Reaction Compressor include
SUSTAIN, which controls the amount of Compression
and Release characteristics. ATTACK determines how
fast the compression reacts. LEVEL controls the output
volume.
Most studio compressors are big and bulky and quite
difcult to set. Rocktron comes to the rescue with
the Reaction Compressor. It’s as easy as 1, 2, 3 to
get professional results that will improve your live
performances.
Here’s some tips. Start by setting the ATTACK and
LEVEL controls around the 12::00 o’clock position.
Turn the SUSTAIN from left to right in small increments
while playing until you achieve the texture you are
seeking. After you have found your favorite sweet spot,

Introduction
use the LEVEL control to ne tune your output level.
That’s it! Sound check is done.
Use the Reaction Compressor as a master SOLO switch
to not only dene what you play but also to raise the
volume! The soundman can worry about something
else…you have performance control!.
Typically you want to set the output level after
compression has been applied so that it is the same as
the pedal in True Bypass – this is called “unity gain” (the
same level from pedal on to pedal off). You may want to
apply compression, and then actually add volume using
the LEVEL control. Now you have added more sustain
and drive which can be used before an overdrive pedal, or
direct into your amplier.
Compression helps dene articulation for any instrument
by limiting how loud a note can get. It also makes
lower volume notes louder. The end result is a smoother
and more even sound, and that is what you hear on
professional recordings. It’s also what you will hear live!
The soundman will thank you!
The footswitch on the Reaction Compressor controls
On/Off status as shown by the LED indicator. Reaction
stomp boxes run on a 9V Alkaline battery, or may also
be powered by Rocktron’s DC OnTap Universal Power
Supply adaptor.

Descriptions

Descriptions continued.........
SUSTAIN Control - This control determines the
amount of dynamic range limiting.
ATTACK Control - This control determines
amount of delay before compression occurs.
Turning the knob to the right produces a faster
attack and to the left a slower attack.
9VDC Input - This input jack provides 9VDC
power to the pedal from the Rocktron DC OnTap
9V power supply (sold seperately).
LEVEL Control - This control determines the
controls the amount of effect added to the output.
ON/OFF Leds - These LEDs shows if the pedal
is on or off. When the LED is lit the pedal is on.
When the LED is not lit the pedal is off.
BATTERY COMPARTMENT and COVER - The
9V battery can be found in this compartment.
INPUT Jack - Using a standard 1/4” guitar cable,
plug your guitar into this jack.
1
2
3
4
5
6
7

Descriptions continued.........
THUMB SCREWS for Battery Compartment.
Unscrew these thumb screws to access the battery
compartment.
FOOTSWITCH - Use this switch to turn on or off
the pedal. The On/Off Led will show you if the
pedal is on or off.
OUTPUT Jack - Using a standard 1/4” guitar
cable you can plug in another pedal from this jack
or plug directly into your amplier.
8
9
10

Typical Connection

Specications
Maximum Input
Maximum Output
Imput Impedance
Output Impedance
Current Consumption
Power Requirements
Dimensions
Weight
3dBu
7dBu
2.2MΩ
10KΩ
45mA
9V Alkaline Battery or
Rocktron DC OnTap Uni-
veral Power Supply (sold
seperately). Negative Tip
125mm x 78mm 61mm
5” x 3.25” x 2.5”
0.7kg
1.5lbs