Rocktron Reaction Digital Delay User manual

May be covered by one or more of the following: U.S. Patents #4538297, 4647876, 4696044, 4745309, 4881047,
4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617.
Other patents pending. Foreign patents pending.
Reaction Digital Delay
Instruction Manual

Your Reaction Digital Delay™pedal has been tested and complies with the following
Standards and Directives as set forth by the European Union:
Council Directive(s): 89/336/EEC Electromagnetic
Compatibility
Standard(s): EN55013, EN50082-1
This means that this product has been designed to meet stringent guidelines on how much
RF energy it can emit, and that it should be immune from other sources of interference when
properly used. Improper use of this equipment could result in increased RF emissions, which
may or may not interfere with other electronic products.
To insure against this possibility, always use good shielded cables for all audio input and
output connections. This will help insure compliance with the Directive(s).
For more information about other Rocktron products, please see your local dealer or one of
our importers closest to you (listed on the Rocktron website
(www.rocktron.com).
Read all instructions contained in this manual.
Keep these instructions
Heed all warnings
Follow all instructions.
Do not use this apparatus near water.
Clean with dry cloth
Copyright © 2009 GHS Corporation
All Rights Reserved.
Compliance

Do not block any ventilation openings (if applicable). Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves or other ap-
paratus (including ampliers) that produce heat.
This product is not equipped with a plug or cable. This pedal runs on a 9 Volt Battery, if a
9Volt DC adapter is the used please follow adapter manufacturer’s operation instructions.
Only used attachments/accessories specied by the manufacturer.
Do not use this product with any case, stand tripod, bracket or table that is not specied by
the manufacturer. Insure that the case, stand, tripod, bracket etc. is properly adjusted and
setup (follow all instructions). Extra care and caution should be taken to avoid tip over
and injury.
Unplug this apparatus during lightening storms or when unused during long periods of time.
Refer all service to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus or if the apparatus has been exposed to rain
or moisture, does not operate normally or has been dropped.
DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. QUALIFIED PERSONNEL
SHOULD SERVICE THIS EQUIPMENT ONLY. DO NOT MAKE ANY INTERNAL
ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT AT ANY TIME OR TAMPER
WITH INTERNAL ELECTRONIC COMPONENTS AT ANY TIME. FAILURE TO FOL-
LOW THESE INSTRUCTIONS MAY VOID THE WARRANTY OF THIS EQUIPMENT
AS WELL AS CAUSING A SHOCK HAZARD.
OPERATING TEMPERATURE
Do not expose this unit to excessive heat. This unit is designed to operate between 32 F and
104 F (0 C and 40 C). This unit may not function properly under extreme temperatures.
Precautions

Introduction
Are you searching for a Digital Delay stomp box
that delivers great sound and outperforms the
competitors when it comes to sonic quality? Pick
up the Rocktron Reaction Digital Delay and surprise
everyone, including yourself!
Rocktron’s Reaction Series pedals are built into a
rugged metal slim form factor chassis, taking up
as little space as possible on your pedalboard. The
Reaction Digital Delay is a TRUE BYPASS pedal:
when you turn it off…it is out of your signal path!
The Reaction Digital Delay is very easy to use.
Controls include LEVEL, which controls the output
level of the effect. MODE determines whether the
Delay time range is Quick (62.5 ms – 125 ms) or
Extended (125 ms – 250 ms). REGEN controls how
many echoes you hear, while TIME controls the
Delay Time selection.
The Reaction Digital Delay has all the smooth full
bodied tone you expect in a delay pedal. If you are
a rocker, we’ve got your back! Just set the Reaction
Digital Delay mode to Extended, then turn

Introduction continued....
the Time control to nd that classic rock phrasing
echo. Country pickers or Rockabilly jammers, set
the Reaction Digital Delay mode to Quick and dial
up your favorite slapback!
Most players nd that delay pedals will sound better
when placed after distortion. If you are using a
distortion pedal, place the Reaction Digital Delay
after the distortion pedal in the signal chain. If
you are using your amplier’s distortion, place the
Reaction Digital Delay in the effects loop section of
the amp, (making sure to follow the instructions in
your amp manual when using the effects loop).
The footswitch on the Reaction Digital Delay
controls On/Off status as shown by the LED
indicator. Reaction stomp boxes run on a 9V
Alkaline battery, or may also be powered by
Rocktron’s DC OnTap Universal Power Supply
adaptor.

Descriptions

Descriptions continued.........
LEVEL Control - This control determines the
overall volume of the delay effect.
QUICK/EXTENDED Switch - This switch
allows selection between two delay times in
milliseconds. The QUICK delay is between 0ms
and 200ms. The EXTENDED delay is between
200ms and 400 ms. The actually delay time is
then adjusted using the TIME control knob.
9VDC Input - This input jack provides 9VDC
power to the pedal from the Rocktron DC OnTap
9V power supply (sold seperately).
REGEN Control - This control determines the
number of reptitions (regeneration) of the delay
effect.
TIME Control - This control determines the
length of the delay effect. This control is used in
conjction with the QUICK/EXTENDED Switch.
ON/OFF Leds - These LEDs shows if the pedal
is on or off. When the LED is lit the pedal is on.
When the LED is not lit the pedal is off.
1
2
3
4
5
6

Descriptions continued.........
BATTERY COMPARTMENT and COVER - The
9V battery can be found in this compartment.
INPUT Jack - Using a standard 1/4” guitar cable,
plug your guitar into this jack.
THUMB SCREWS for Battery Compartment.
Unscrew these thunb screws to access the battery
compartment.
FOOTSWITCH - Use this switch to turn on or off
the pedal. The On/Off Led will show you if the
pedal is on or off.
OUTPUT Jack - Using a standard 1/4” guitar
cable you can plug in another pedal from this jack
or plug directly into your amplier.
7
8
9
10
11

Typical Connection

Specications:
Maximum Input
Maximum Output
Imput Impedance
Output Impedance
Current Consumption
Power Requirements
Dimensions
Weight
2dBu
3dBu
1MΩ
1kΩ
36mA
9V Alkaline Battery or
Rocktron DC OnTap Uni-
veral Power Supply (sold
seperately). Negative Tip.
125mm x 78mm 61mm
5” x 3.25” x 2.5”
0.7kg
1.5lbs