Rockustics XT-PowerRock Configuration guide

XT-PowerRock
INSTALL INSTRUCTIONS
© 2021 MSE Audio. Rev. 02.19.2021
Ultra-Fidelity Outdoor Speakers
Contact: MSE Audio, 855.663.5600 / 913.663.5600 / [email protected]
Please read the following instructions carefully before install-
ing your Rockustics®Rock speaker. If you have any questions
regarding installation that are not answered in the following
directions, please contact your local sound contractor or the
Rockustics®/MSE Audio®technical support team.
Basic Wiring
(Diagram A) Locate speaker wire on the underside of the rock.
If necessary, strip the wire ends and trim the wire to the appro-
priate length. Use the supplied silicone wire nut to connect the
positive (red) leads of the speaker and input wires. Repeat this
step with the negative (black) leads. Rockustics recommends
using 14ga or heavier Direct Burial cable for the connection be-
tween the amplier and the speakers.
NOTE: The provided wire nuts are meant for permanent installa-
tion use only. If you are temporarily wiring the speakers, do not
use these wire nuts. In the event you have used the wire nuts,
and need to re-wire your system, do not attempt to unscrew the
nuts. Instead, clip the wires below the nut, and follow the steps
in the Basic Wiring section with a new pair of waterproof wire
nuts (these are available at most hardware stores).
Optimizing Speaker Placement for Best Sound
All Rockustics speakers can generate a high SPL (sound
pressure level). Be ready to rock, but be considerate of your
neighbors! Maximum acoustic performance should be an
important factor in determining speaker placement. Here is how
to achieve it:
1) Establish where the most likely or average listening
position will be.
2) The speakers should be placed at or close to the same
distance from that point.
3) The actual distance between the listening position and
the location of the speakers is not critical. However, keep
in mind that as the distance between listening area and
speaker is increased, there will be a noticeable decrease
in perceived volume.
4) Be sure to conrm amp power matches the power rating
on the speaker. Over-driving the speaker can lead to
permanent damage that is not covered under warranty.
Optimizing Aesthetics with Speaker Placement
All Rockustics products are designed with a boost in high
frequency response to accommodate for placement near
plants and other landscaping features. Feel free to position the
product within your landscaping, camouaged near bushes
or shrubs. Rockustics products strive to blend into the natural
aesthetic of their surroundings.
Be sure to account for the wires which will run from the rock to
your stereo or audio source. Camouage wires by running them
an inch below ground level when possible.
Diagram A

XT-PowerRock
INSTALL INSTRUCTIONS
© 2021 MSE Audio. Rev. 02.19.2021
Ultra-Fidelity Outdoor Speakers
Contact: MSE Audio, 855.663.5600 / 913.663.5600 / [email protected]
Cautions and Maintenance
All Rockustics Rock Series speakers are sealed and fully
weatherproof. However, DO NOT place speakers where
the grille will be in the path of a sprinkler system. Sprinklers
typically have a high water pressure level that can damage
speaker cones if hit directly.
DO NOT place soil or wood chips over the speaker grille. If the
grilles accumulate a build up of soil, the speaker may become
damaged. If build up does occur, simply rinse the grille with a
garden hose set to a low pressure level. Accumulated soil may
also promote undesired insect trafc into the speaker. Insects
may eat through the speaker cone. Chemical sprays may also
cause damage to the rubber of the speaker surround. This in-
cludes bug spray, deck sealant, some fertilizers and oil based
products. Speakers MUST be covered when applying these
treatments or chemicals in your yard.
For environments that get snow and ice during the winter
months, be sure to check that the openings and woofer cone
are clear and there is no hard-packed snow or ice built up in
these areas before playing. If there is ice or snow present on
the cone, use a hair dryer set on a low setting to to melt it away.
If the speakers are not going to be used during winter months, it
is recommended that they either be disconnected and brought
indoors, or covered with a plastic bag to help protect the
speaker components.
Step by Step Setup
1. Locating Wire
Locate speaker wire on the
underside of the speaker. Strip
wire ends if necessary.
2. Gasket
Attach the gasket to the smooth
side of the bottom cover plate.
3. Attaching Gland
Attach the supplied liquid-tight
strain relief gland to the cover
plate and thread signal wires
through the gland.
4. Conduit
Attach the conduit clamp to the
cover plate. It may be neces-
sary to increase the opening in
the cover plate to t the conduit
connector. Thread signal wires
through the conduit clamp and
afx the conduit clamp.
5. Connecting Wire
Connect the speaker wire to
the input signal wire. Red is
positive, black is negative. Use
included wire nuts to secure
the connection. Tuck wires and
wire nuts into the pocket on
the underside of the speaker.
6. Tap Settings
To change tap settings, locat-
ed the tap switch on the ud-
nerside of the rock behind the
cover plate. Use a small at
head screwdriver to adjust the
switch for the desired setting.
The tap switch is a six-position
rotary switch with positions
for 120 W, 60 W, 30 W, 15 W,
7.5 W, and transformer bypass
(8Ω). The tap switch will be set
to the highest 70.7 volt setting
from the factory (120 W).
7. Cover Plate
Place cover plate over the pocket
on the underside of the speaker
and secure with the 4 supplied
screws. This process will be the
same if you are using the conduit.
8. Done
2.
1.