Rockwell Automation Allen-Bradley TLP-SSN-F046 User manual

Installation Instructions
Original Instructions
Shaft Seal Kits for Kinetix TLP Servo Motors
Catalog Numbers TLP-SSN-F046, TLP-SSN-F070, TLP-SSN-F090, TLP-SSN-F100, TLP-SSN-F115,
TLP-SSN-F145, TLP-SSN-F200, TLP-SSN-F235
Topic Page
About Shaft Seals 2
Required Tools 2
Required Supplies 2
Remove the Shaft Seal 3
Replace the Shaft Seal 4
Shaft Seal Kit Catalog Numbers 6
Additional Resources 7

2Rockwell Automation Publication 2090-IN044B-EN-P - September 2019
Shaft Seal Kits for Kinetix TLP Servo Motors
About Shaft Seals
A shaft seal is recommended if the motor shaft and end bell are exposed to significant amounts of
containments, such as oil, fluids, or fine dust. Use a shaft seal in these environments to prolong
the life of the motor. A shaft seal and Bulletin 2090 cables with environmentally sealed
connectors are required for an IP65 rating or greater.
See Kinetix® Motion Accessories Specifications Technical Data, publication KNX-TD004, to
find Bulletin 2090 cables with environmentally sealed connectors for your motor.
Required Tools
Use these tools to install a shaft seal:
• Insulated, small, flat-head screw driver
• Rubber/wooden mallet or a metal hammer and wooden work piece
• Socket, pipe, or tube (various sizes)
• Abrasive cloth to remove any nicks or burrs from the motor shaft
Required Supplies
Lubricant - Grease, industrial grade, suitable for applications with speeds up to 6000 RPM, and
–10…+80 °C (14…176 °F) temperature range.
IMPORTANT The shaft seal is not required in applications where the motor shaft and end bell are free of oil,
fluids, or fine dust, and a lower IP rating is sufficient.
Shaft seals are subject to wear and require periodic inspection and replacement. Replacement
is recommended every 3 months, not to exceed 12 months, depending on use.
If you paint the motor, do not get paint on the shaft seal area or the shaft, as paint can decrease
the life of the shaft seal.
Oil, Fluids, and Fine Dust Oil, Fluids, and Fine Dust
Shaft Seal Installations
Recommended
Shaft Seal Installation
is Not Recommended
Motor Shaft and
End Bell are Exposed
to Containments
Motor Shaft and
End Bell are Protected
From Containments
Shaft Seal Installation
is Not Recommended

Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 3
Shaft Seal Kits for Kinetix TLP Servo Motors
Remove the Shaft Seal
Follow these steps to remove the shaft seal.
1. Remove power to the motor before removing the shaft seal.
2. Remove the shaft key (if present) from the motor shaft.
3. Remove old seal.
Place the insulated screw driver on the inside diameter of the shaft seal outer lip as
shown. Carefully lift the seal, work your way around the seal lift a little at a time. When
you can grasp the seal, slightly rotate it while pulling it out of the front-end bell.
4. Inspect and clean the shaft and seal surfaces as necessary.
Use an abrasive cloth to remove any nicks or burrs from the motor shaft.
ATTENTION: To avoid injury or damage to the equipment, remove power from the motor before
removing the shaft seal.
ATTENTION: Avoid damage to the motor. Do not pry against front-end bell or shaft.
ATTENTION: Do not hammer the shaft or body of the motor when changing the shaft seal.
Do not remove screws.
Do not pry against
front-end bell or shaft.
Outer Lip

4Rockwell Automation Publication 2090-IN044B-EN-P - September 2019
Shaft Seal Kits for Kinetix TLP Servo Motors
Replace the Shaft Seal
Follow these steps to replace the shaft seal.
1. Apply tape to the keyway so the edges do not damage the seal lip.
2. Lubricate the motor shaft and the inner and outer lip of the shaft seal.
3. Center the shaft seal on the mounting surface of the motor and slide the shaft seal evenly
onto the motor shaft.
See Shaft Seal Installation Clearances on page 5 for the correct installation clearance of
the shaft seal you are installing.
4. Press the shaft seal into the seal bore by applying one of the Shaft Seal Installation
Methods on page 6.
5. Visually inspect for irregularities in the shaft seal or an uneven alignment where the shaft
seal contacts the motor.
Verify that the outer and inner circumference of the shaft seal is fully seated into
position.
6. Verify that the shaft seal is installed to the correct installation clearance.
• If the shaft seal is installed too deep, it can become subject to excessive wear and
require frequent replacement.
• If the shaft seal is installed too shallow, it can reduce the effectiveness of the
protective seal.
7. Replace the shaft key.
Applies to motors that include a keyed shaft.
IMPORTANT Cover the sharp edges of the keyway with tape to protect the shaft seal lip from
damage.
IMPORTANT Shaft seals require a lubricant to reduce wear. Lubricate only the inner and outer lip
of the shaft seal. Do not lubricate the motor bore or outside diameter of the seal.
Back View of Shaft Seal
(motor facing)
Inner Shaft Seal Lip
Inner Shaft Seal Lip
Outer Shaft Seal Lip

Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 5
Shaft Seal Kits for Kinetix TLP Servo Motors
Shaft Seal Installation Clearances
Motor Cat. No.
Shaft Seal Installation Clearance
Min, mm (in.) Nom, mm (in.) Max, mm (in.)
TLP-A0xx Press the shaft seal so that the seal is flush with the front surface of the motor.
TLP-A1xx and TLP-A2xx 0.00 (0.00) 0.10 (0.004) 0.20 (0.008)
Front Surface
of Motor
Shaft Seal Pressed
Flush with Front
Surface of Motor
Shaft Seal Pressed
Below Front
Surface of Motor
Front Surface
of Motor
Nom
Min
Max Bulletin TLP-A0xx
Shaft Seal Example
Bulletin TLP-A1xx and TLP-A2xx
Shaft Seal Example
Shaft Seal
Shaft
Shaft Seal

6Rockwell Automation Publication 2090-IN044B-EN-P - September 2019
Shaft Seal Kits for Kinetix TLP Servo Motors
Shaft Seal Installation Methods
Shaft Seal Kit Catalog Numbers
ATTENTION: Do not hammer directly on the shaft seal. Gently tap the socket, pipe, or tube evenly
around the outer edge of the shaft seal until the shaft seal is pressed into place. Make sure the
socket, pipe, or tube you use does not contact the shaft seal lip. Permanent damage to the shaft
seal can occur.
IMPORTANT Third-party shaft seals are not approved for use with these motors.The use of third-party shaft
seals voids any implied or expressed warranties.
Kinetix TLP Low Inertia Motors
Motor Cat. No. Shaft Seal Kit Cat. No.
TPL-A046 TLP-SSN-F046
TPL-A070 TLP-SSN-F070
TPL-A090 TLP-SSN-F090
TPL-A100 TLP-SSN-F100
TPL-A115 TLP-SSN-F115
TPL-A145 TLP-SSN-F145
TPL-A200 TLP-SSN-F200
TPL-A235 TLP-SSN-F235
Socket, Pipe, orTube
(supplied by the customer)
Motor
Metal
Hammer
Shaft Seal
Wooden
Work
Piece
Rubber or
Wooden Mallet
Motor
Shaft Seal
Socket, Pipe, orTube
(supplied by the customer)
Or

Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 7
Shaft Seal Kits for Kinetix TLP Servo Motors
Additional Resources
These documents contain additional information concerning related products from Rockwell
Automation.
You can view or download publications at http://www.rockwellautomation.com/global/
literature-library/overview.page.
Resource Description
Kinetix Rotary Motion Specifications Technical Data,
publication KNX-TD001
Product specifications for Kinetix VP (Bulletin VPL, VPC, VPF, VPH,
VPS), MP-Series™ (Bulletin MPL, MPM, MPF, MPS), andTL-Series™
rotary motors.
Kinetix Motion Accessories Specifications Technical Data,
publication KNX-TD004
Product specifications for Bulletin 2090 motor and interface cables,
low-profile connector kits, drive power components, and other servo
drive accessory items.
Kinetix Motion Control Selection Guide,
publication KNX-SG001
Overview of Kinetix servo drives, motors, actuators, and motion
accessories that are designed to help make initial decisions for the
motion control products best suited for your system requirements.
Industrial AutomationWiring and Grounding Guidelines,
publication 1770-4.1
Provides general guidelines for installing a Rockwell Automation
industrial system.
Product Certifications website, rok.auto/certifications Provides declarations of conformity, certificates, and other
certification details.

Allen-Bradley, Kinetix, MP-Series, Rockwell Automation, Rockwell Software, and TL-Series are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: [phone]
Rockwell Automation maintains current product environmental information on its website at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Publication 2090-IN044B-EN-P - September 2019
Supersedes Publication 2090-IN044A-EN-P - September 2019 Copyright © 2019 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
5014099301-QO01
*QO01*
Rockwell Automation Support
Use the following resources to access support information.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions
on how to improve this document, complete the How Are We Doing? form at http://
literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.
Technical Support
Center
Knowledgebase Articles,
How-to Videos, FAQs, Chat,
User Forums, and Product
Notification Updates.
https://rockwellautomation.custhelp.com/
Local Technical
Support Phone
Numbers
Locate the phone number
for your country.
http://www.rockwellautomation.com/global/support/get-support-
now.page
Direct Dial Codes
Find the Direct Dial Code
for your product. Use the
code to route your call
directly to a technical
support engineer.
http://www.rockwellautomation.com/global/support/direct-dial.page
Literature Library
Installation Instructions,
Manuals, Brochures, and
Technical Data.
http://www.rockwellautomation.com/global/literature-library/
overview.page
Product
Compatibility and
Download Center
(PCDC)
Get help determining how
products interact, check
features and capabilities,
and find associated
firmware.
http://www.rockwellautomation.com/global/support/pcdc.page