RoDEK RT-15 User manual

RD-UM-005(E) Rev.0 RODEK Co.,Ltd
RC-100
RC-200
RC-500
Ver 1.3
July.2020
RC-100
RC-200
RC-500

-1-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
■TABLE OF CONTENTS
Preface -------------------------------------------------------------------- 1
Safety alert signs --------------------------------------------------------- 2
Safety Precautions ------------------------------------------------------- 4
Management ------------------------------------------------------------- 6
Alarm indication and its location ---------------------------------------- 7
Names of parts and functions ------------------------------------------- 9
User’s guide --------------------------------------------------------------13
Problems ---------------------------------------------------------------- 15
References data --------------------------------------------------------- 15
Management and inspection ------------------------------------------- 17
Fuse Replacement ------------------------------------------------------ 17
Warranty period ---------------------------------------------------------18
Precautions when using ------------------------------------------------ 19
Storage after use, and how to maintain --------------------------------20
Installation guide --------------------------------------------------------21
Box components ---------------------------------------------------------48
Detail Description -------------------------------------------------------50
Rough map of company ------------------------------------------------51
■PREFACE
Thank you for purchasing Refraction Unit RT-15.
RT-15 supports 2-instruments on a rotatable sliding table. Possible to tilt
seat back, rotate the headrest, armrest, and set. Also, it is able to make
to lowest location of chairs as one touch. This is the unit Chair of
ergonomic design that enables to take treatment as one-stop including
eye testing through Phoropter. You can select three kinds of chairs.

-2-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
Operation environment
Use the system in normal living conditions;
Operation : +10 to +40°C, 30 to 75% r.h., 70 to 106 kPa
For smooth operation, install the system horizontal and stable.
Make sure the system properly connected to electricity.
Power Supply (SMPS) Voltage should be within the range
230V~ 50/60Hz
Keep the Power OFF when the system not in used
■SAFETY ALERT SIGNS
In the Operation Manual and at the main body of the system, there
stated important alerts to prevent property damages and for the
safety of operator and other peoples.
Please read carefully of the “Safety Precautions”, and fully understand
and follow the safety indication and symbols.
Indications and their meaning
Warning
Warning indicates death, severe personal injury can result in if
proper precautions are not taken
Caution Caution indicates minor personal injury or property damage can
result in if proper precautions are not taken.
Symbols and their meaning
Template for a prohibition sign (red circle and diagonal);
The black symbol or text shall be placed centrally on the background and
shall not obliterate the cross bar, or a supplementary text next to the sign.
Template for a mandatory action sign (blue background); The white symbol
or text shall be placed centrally on the background, or a supplementary text
next to the sign.

-3-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
Template for a warning sign (yellow background and black triangle); The
black symbol or text shall be placed centrally on the background, or a
supplementary text next to the sign.
Follow instructions for use
Manufacturer
Date of Manufacture
Serial no.
Indicates a medical device that needs protection from light sources.
No pushing
Indicates the temperature limits to which the medical device can be safely
exposed.
Indicates the range of humidity to which the medical device can be safely
exposed.
Warning - Disposal of waste products
1. When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2012/19/EU.
2. All electrical and electronic products should be disposed of separately from
the municipal waste stream via designated collection facilities appointed by
the government or the local authorities.
3. The correct disposal of your waste products will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your waste products,
please contact your city office, waste disposal service or the shop where you
purchased the product.
Type B applied part (Patient chair)

-4-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
■SAFETY PRECAUTIONS
Symbols Prohibit items
Do not disassemble the unit for repairing.
Electric shock is possible.
Contact the sales shop for the repairing.
Do not place the unit at the water or other liquid spraying
area. Fire or electric shock is possible.
!
Connect the unit to single-phase AC power plug.
Elsewhere, can cause fire and electric shock.
!
Replace the fuse only after power cord unplugged.
Otherwise, an electric shock may occur.
Use a rated fuse.
Unplug the power cord immediately when smokes
or any
other problem occurs.
Otherwise there is a danger of fire.
Please contact the sales shop for the repairing.
Do not place the equipment unstable or slanted over 5 ˚.
The equipment can cause injury to you.
Do not place heavy material over the specified weight on
the table. The equipment can cause injury to you.
Do not put your fingers to the running machine.
The equipment can cause injury to you.
Do not open the cover as you can get the electric shock.
Contact sales shop when the repairing needed.
Tighten the PHOROPTER hanger bolt securely.
Fall off may cause injury.

-5-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
Symbols Prohibit items
Do not hang heavy material of over 7Kg on the
PHOROPTER ARM.
Fall off may cause injury.
To avoid the risk of electric shock, this equipment must
only be connected to supply mains with protective earth.
Malfunction may happen due to electromagnetic
interferences caused by high frequency equipment, such as
mobile phones. Be sure to keep away from such a high
frequency equipment.
Connecting electrical equipment to the multiple socket-
outlet effectively leads to creating a medical electrical
system, and can result in a reduced level of safety.
The responsible organization (accountable for the use and
maintenance of a medical electrical system) shall be
referred to EN 60601-1, 3rd edition for requirements.
The external and internal socket-outlets shall be connected
with ophthalmic instruments only complying with IEC
60601-1.

-6-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
■MANAGEMENT
Operator’s Management
Other than that indicated in this manual, for safety reason, do not
perform the administrative maintenance tasks on the equipment
except for qualified service man. However, customers can manage
the items listed below:
Replace of the Fuse
The fuse is replaceable item. Refer to its handling method in the
textbook.
Replace of the Light Bulb
Refer to its handling method in the textbook.
Disclaimer
We do not take responsibility for the damages caused by fire,
earthquakes, acts by third parties, or other accidents, and
damages caused by negligence, or misuse in abnormal condition.
We do not take responsibility for the damages caused by
abnormal use of the machine that are not described in the
instruction manual.
We do not take responsibility for bad treatment result as it is due
to the doctors’ diagnostic and responsible by the doctor.

-7-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
■ALARM INDICATION and ITS LOCATION
For safety reason, there are alarm indications on the equipment.
Please follow the indications. If you find any discrepancy in the
indication sign, please inform it to us with the detail status.
ALARM INDICATION
Caution
①Tighten the assembly bolts of Vision Tester.
Fall down may cause injury.
②
Do not give excessive load to the arm such as
hang on or pull down. Fall down of arm may
cause injury.
③
Do not open the cover as it may cause electric
shock. Repairing should
be done by service
technician.
④Do not access to rotation range of arm as there’s
a risk of injury due to collision.
In addition, do not use the
rotation range in excess
of specified range (16 ˚ ± 3 ˚)
when positioning to
treatment suspension. There is a risk of collision
to
side wall or to other material.
⑤Replacing of the fuse should be done aft
er
disconnecting electricity, otherwi
se electric shock
may occurs.
⑥
Do not use the slit lamp when the power supply
box tightening bolts at least 20 in advance
Bolt
can be projected to the top of the table

-8-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
Location of Warning signs

-9-
RD-UM-005(E) Rev.0 RODEK Co.,Ltd
■THE NAME and FUNCTION OF EACH PART