Roksan Audio RMX-108 User manual

Roksan
RMX-108
User Manual

Roksan RMX-108 User’s Manual
1
RMX-108 Features
·Macro sequence function—each macro
can store 60 commands
·Controls up to six devices, including DVDs,
TVs, Satellite Receivers, VCRs and other
infrared remote control devices
·IR code learning from existing remote
controls for quick configuration
·Preset manufacturer’s codes for many
models
·Up to 44 user-programmable keys for each
device
·Automatic Power Saving mode turns off the
remote after 90 seconds of inactivity
Unpacking the RMX-108
Check the package to make sure the following
items are included.
·RMX-108
·Batteries

2
Battery Indicator
A battery icon is displayed in the upper left-hand
corner above the Mute button.
When the batteries are almost discharged, the
battery low icon appears.
Roksan RMX-108 User’s Manual

3
About the controls
The number of soft buttons on the touch screen
changes according to the selected device. The
touch screen soft buttons allow you to operate
the RMX-108 and your external devices. Use
these keys to program codes from your existing
remotes, control your devices, and set up
macros. You will hear a beep when you press a
button. The RMX-108 turns itself off after 90
seconds of inactivity
Touch screen precautions
·Tap the LCD touch screen gently. Do not
use excessive force.
·Do not use pens or sharp objects to tap the
screen, as you might damage the surface.
·Keep the RMX-108 dry. Wipe off any spills
immediately. Never immerse it in liquid.
·Do not expose the RMX-108 to extreme
temperatures. Keep it away from heat
sources.
·Avoid dropping the RMX-108.
·Do not drop anything on the touch screen.
·Clean the LCD touch screen with a soft,
damp cloth. Do not use abrasives or
cleaning solutions.
Roksan RMX-108 User’s Manual

About the controls
4
Selecting devices and pages
You can program the hard buttons as well as
two pages of soft buttons (on the touch screen)
for up to six devices. To change between
devices, press the appropriate device button. To
switch between pages, press the device button
again. The current page is indicated by or
in the top right corner of the touch screen.

5
Setting up the RMX-108
Entering setup
To enter setup, press and hold the button for
two seconds. From the setup screen, you can
·Setup preset codes
·Learning codes
·Creating Macros
·Delete key codes
·Delete devices codes
·Reset the handset
NOTES:
When the battery low icon appears, you will not
be able to enter setup. Please renew batteries to
entering setup.

Learning codes
6
Roksan RMX-108 User’s Manual
Learning codes
You can use your existing IR remote control to
“teach” the RMX-108. You can program all
buttons except for the DEVICE keys.
NOTE: Not all codes can be learned. If the RMX-108
cannot learn a code, three beeps are emitted.
1. Set both remotes on a flat surface with the
target device’s remote control pointed at the
SRC-1600’s learning eye, for about 5 ~10 cm
apart.
2. On the SRC-1600, press the device button of
the device you want to
program.
3. Press and hold to enter
setup.
4. Press .
5. On the SRC-1600, press the
button to indicate the key you
want to program. Including Touch screen
buttons and hard buttons. Touch screen
buttons flash when you select them. Press the
device button to switch between touch
screen pages.

7
6. Aim the IR
transmitter of your
device’s remote
control at the
learning eye of
the RMX-108.
7. Continually press the corresponding button on
your existing remote control until the RMX-108
LED lights.
If the function is not learned correctly, the LED
flashes three times and the RMX-108 emits a
triple beep. Do the relearning procedure
again.
8. When the code has been learned, the
RMX-108 emits a beep and the LED on the
RMX-108 lights until you release the button on
the device’s remote.
9. Repeat steps 5 – 8 for all the buttons you want
to program.
10. When you have finished, press .
Roksan RMX-108 User’s Manual

Deleting codes
8
NOTES:
·Programming a button overwrites any previous
function.
·When the SRC-1600 has successfully learned a
function it beeps once and the LED lights up
until you release the remote control’s button.
Deleting codes
You can delete codes if you no longer want to
use the function or if you want to re-program a
button. You can delete codes one button at a
time or an entire device at a time.
NOTES:
·Deleting codes does not remove the button
from the layout.
·You do not need to delete a code to
Re-program a button. You can overwrite
codes
by automatically or manually entering preset
codes or by learning from an existing remote

9
Deleting codes one button at a time
1. Select the appropriate device by pressing the
device button.
2. Press and hold to enter setup.
3. Press .
4. Press the button you want
to delete.
5. Repeat step 4 for all the
buttons you want to
delete.
6. Press .
Deleting codes one device at a time
1. Select the appropriate device by pressing the
device button.
2. Press and hold to enter
setup.
3. Press .
4. Press to confirm. Otherwise,
press to cancel.
5. To delete other devices,
repeat steps 1 ~ 3. Otherwise, press to
leave this mode.
Roksan RMX-108 User’s Manual