Roksan Audio RMX-111 User manual

Learning System
Remote Handset

ROKSAN - RMX111 USER MANUAL
1. Quick Launch Page 1
2. Before you start Page 2
3. Connecting to a PC for the first time Page 3 - 5
4. Registering the RMX111 for the first time Page 3 - 5
5. Setting codes via online database Page 3 -5
6. Storing IR codes manually Page 6
7. Operating the RMX111 Page7
8. Restoring the RMX111 to default Page 7
9. Maintenance / Trouble Shooting Page 8
10. Lock up & Reset Page 9
TABLE OF CONTENT

1
QUICK LAUNCH
General Functions
1. Infrared Indicator
2. LED Indicator
3. Devices selector keys
3a. Kandy Device Selector
3b. Caspian Device Selector
4. Function Keys
4a. Multi Track Selector
5. Battery Compartment
6. USB Connector
7. CD Transport Keys
11. Tape ON/OFF
12. Tuner Function Button
CD Player Functions
a. Fast Backward
b. Play
c. Pause
d. Fast Forward
e. Shuffle
f. Repeat 1/All
g. Stop
h. Next Track
i. Previous Track
Note: Display ‘Time’ button is actuated
manually on front panel.
Amplifier Functions
8. Mode (Caspian) /Mute (Kandy)
9. Master Volume
10. Input Selector
6
1
2
3
3a
8
3b
9
4a
b
fe
a
4
5
12
11
10
7
c
g
h
i
d

2
BEFORE YOU START
BEFORE YOU START
PC SYSTEM REQUIREMENTS (MINIMUM)
HOW TO INSTALL BATTERIES
HOW TO SET UP YOUR REMOTE
Congratulations! Your Roksan RMX111 Universal Remote Control is a state of the art device which
integrates many different Infra-red remote controls to deliver instant A/V control action to your fingertips.
Before operating the remote, please read thoroughly.
Please keep this manual for future use.
1. Roksan RMX111
2. USB Cables type A to USB Type B mini
3. Manual
• Microsoft Windows XP/Vista/7
• 512MB RAM & 300MB Free Disk Space
• Available USB2.0 Port x 1
• Installed Microsoft Internet Explorer 8.0 (or newer)
• Established Reliable Internet Connection
Please note: Due to security reason of Microsoft Windows Vista / 7, the set-up program and drivers of
your RMX111 will not be executed automatically
(Program auto-run is prohibited). Please double click pop-up window - CD ROM Drive - KRMAP and
KRMAP.exe to install the program and drivers manually.
Alkaline batteries are always recommended. The Roksan RMX111 requires two batteries.
1. Remove the battery cover on the back of your RMX111.
2. Observe the polarity of the batteries and the “+/-” marks inside the battery compartment.
3. Insert the batteries accordingly.
4. Push the battery cover back in place.
Please Note: Whenever you see the LED indicator of your remote flashes 3 times after you have pressed
any key, it tells your batteries are running low.
Please replace with the new and fresh alkaline batteries to ensure proper operation and performance.
Your RMX111 can replace up to 8 original A/V remote controls. Before your remote can operate your A/V
devices, you firstly have to register it. Once this step is complete, you can go through the following easy
online setup procedure (Page 4) procedures to set your remote control handset.

3
EASY ONLINE SETUP
BY SMART LEARNING
• A reliable internet connection and PC system loaded with Windows XP / Vista / 7 is required.
• Please make sure you have a PC system loaded with Windows XP / Vista / 7, installed with Microsoft
Internet Explorer 8 and it is connected to a reliable internet connection throughout the whole setup
process.
• Please also have your various other devices and model number ready.
Please follow the simple setup procedures on the Online Remote Code Database web page throughout
the whole setup:
1. Remove the battery cover on the back of your remote.
2. Make sure your remote is loaded with fresh batteries.
3. Locate the mini USB connector inside the battery compartment.
4. Connect your remote with the supplied USB cable to your PC (via one of the available USB Ports).
5. Once, your remote is connected to your PC, the installation program will be started automatically ( all
necessary device drivers will be installed to your PC automatically, only for the 1st time connection/
setup). When the installation is completed your PC will launch a browser ( Internet Explorer ) to reach
out online database server.
Remark: If your browser is not running after the connection of your remote to the PC, you have to double-
click the icon ( KRMAP.exe) manually on your desktop to start ( for Windows Vista / 7 users).
Register your RMX111 - Required only once!
New user-Please register your RMX111 by filling in your name and email address. Simply follow the
procedure below and you can activate your new Roksan RMX 111 in a very short time. Once all the neces-
sary drivers and the auto-run program have been installed, you will be prompted at the following page. Fill
in your information under the space provided with marks * and then click Confirm to send your file. Your
RMX111 will be activated and ready for a further setup.

4
Set up your Roksan RMX111 via one of the methods below:
1. Easy Online Setup
2. Smart Learning
EASY ONLINE SETUP
1. Select Remote Setup page
2. On the Remote Setup page, simply select your Device type (e.g. TV), type in your Device name (e.g.
SONY KV-J29MH9), select Brand - SONY from the drop down list and select model from the drop
down list.
3. Repeat step 2 for the rest of your other devices, such as VCR, DVD, SAT, CBL, STB, etc.
4. Press to re-confirm your selected setting.
5. Press to activate the data file

6. Press to download the data file automatically to your remote.
WARNING:
Do Not try to press for data file download. For security reasons, each remote has been limited to
5 attempts for SAVING the data file to the user’s local computer. After that, your remote will be LOCKED.
Please make sure that this is really necessary for such action.
(For more information please see Page 9)
7. Disconnect the USB cable from the remote. Turn on your device (e.g. TV), try the function keys on
the remote. If your device (e.g. TV) responds to your invoked function correctly, your remote has been
loaded with the right Device Code. Otherwise, repeat the above set-up instructions with the rest avail-
able Device Codes until your device (e.g. TV) responds to your invoked function, and most keys work
correctly.
Remarks:
• Always keep secure connection of the remote and the PC system throughout the whole “Easy Online
Setup” process.
• After the remote code is downloaded to the remote, simply disconnect it from the USB cable and try
the functions.
• If you cannot find a correct Device Code for you equipment, you should try to select a code with a
similar description of your device. (e.g if your TV is 29XUMH, where you can see a 32XUMH on the
available code, you can try to use this code 32XUMH), as the manufacturers tend to use the same
remote code for a series of products, simply reconnect your remote with your computer and try another
available codes. (refer to the above steps.)
• Should only some of the commands work for your device, you can either select another code or try to
copy the rest of the commands to your remote from your original remote, see the “By Smart Learning”
section.
• Do Not try to press for data file download. For security reason each RMX111 has been
limited to 5 attempts for SAVING the data file to the users local computer. After that, your remote will
be LOCKED. Please make sure that this is really necessary for such action (See more information on
page 9).
5

6
If you cannot find a correct device code for your equipment from the Online Database, you can copy your
device’s original remote control commands to your RMX111. Your RMX111 allows you to store up to 360
additional remote control commands and all 8 device modes can facilitate learning in seconds. Please fol-
low the instructions below to start the process:
(Please have your original remote controls ready for the code copying process)
1. Select a desired Device Mode (e.g. TV, if you want to set up your RMX111 to operate your TV).
2. Press and Hold the Device Mode key e.g for 3 seconds, the LED indicator will light up.
3. Release the Device Mode key e.g.
4. Press and Release a desired key on the RMX111 you want to hold the function key, the LED will flash
slowly.
(Now aim your device remote control to the RMX111 Infra Red Lens on a flat surface with 1-3 cm apart.
Make sure your A/V remote control is loaded with fresh batteries).
5. Press and hold the corresponding key on your
original A/V remote control to transfer the command.
The LED indicator of the RMX111 will flash. When
the command has been copied successfully, the LED
indicator will stay on. You can release the key on
the A/V remote control. If the LED indicator keeps
flashing quickly, it shows an error in learning process.
Please adjust the position of both remote controls
and repeat steps 4 & 5 again.
6. Repeat step 4 & 5 to transfer other commands into
the rest of the function keys.
7. When you have finished the whole device mode. Press and hold the corresponding device Mode Key
e.g. for 3 seconds to save all the copied commands and exit the learning mode.
Remarks:
• Your RMX111 will quit the learning mode automatically after 30 seconds of idle period.
• If you want to quit the learning mode at any time, simply Press and Hold the corresponding Device
Mode key for 3 seconds.
• Downloading a new Device Code from the Online Setup will automatically erase and replace all
learned commands in the chosen device mode.
• When you have finished copying and teaching the original device’s commands to your RMX111 you
can upload your RMX111 to our online database for future retrieval. Please connect your RMX111 to
your PC, the system will prompt a set of automatic actions.
A MASTER RESET OF YOUR RMX111 WILL ERASE ALL NEWLY LEARNED COMMANDS
SMART LEARNING - STORING IR CODES MANUALLY
TV
TV
TV

7
Normal Operation
Once you have set up the RMX111 for your system’s equipment, it works like your original remote controls.
To operate, just aim it at your equipment, press an appropriate device mode key and invoke the desired
function by pressing a corresponding key on the RMX111. The indicator flashes during signal transmission
and as confirmation of key being pressed.
Master Reset/Reset/Default
Master reset allows you to reset your RMX111 to its factory default state.
After Master Reset, you have to setup the remote all over again. Before you press
master reset, please make sure it is really necessary.
1. Remove the battery cover on the back side of your remote.
2. Make sure your RMX111 is loaded with fresh batteries.
3. Locate the mini USB connector inside the battery compartment.
4. Connect your RMX111 with the provided USB cable to your PC (via one of the available USB Port).
5. Once, your RMX111 is connected to your PC, it will launch an Window Internet Explorer browser to
reach our online database setup server. if your browser is not running after the connection of the
RMX111 to your PC, you have to double-click the icon (KRMAP.exe) on your desktop.
6. On the remote set up page simply click the button once.
Wait 1 minute, your RMX111 will be reset to factory default.
OPERATING THE RMX111
ResetDefault

8
Remarks: Master Reset of RMX111 will erase all previously copied commands as well.
MAINTENANCE
TROUBLE - SHOOTING
1. Do not expose your URC to dust, strong sunlight, humidity, high temperature or mechanical shock.
2. Do not use old and new batteries together as old batteries tend to leak.
3. Do not use corrosive or abrasive cleaner on your URC.
4. Keep the unit always dust free by wiping it only with a soft and dry cloth.
5. Do not disassemble your URC, it contains no user- serviceable parts
Q. My remote RMX111 does not work at all!
A. Check if you have set up your remote RMX111 by Easy Online Setup or Smart Learning.
A. IMPORTANT REMARKS for Windows Vista / 7 users, after you connect your remote RMX111 to your
computer, please double click to pop up window - CD ROM Drive - KRMAP and the KRMAP.exe to
install the program and drivers.
A. Check your A/V device, if the device’s mains switch is turned off, your remote RMX111 could not operate
your device.
A. Check whether your batteries are inserted properly and are in correct +/- marks.
A. Check whether you have pressed the corresponding device mode key for your device.
A. If the batteries are low, replace the batteries.
A. Try to connect your remote RMX111 to your PC and reload the user data by selecting
on the Remote Setup Page.
UserCong

9
RMX111 LOCK UP AND RESET
Q. If several Device Codes are listed under the brand of my A/V device, how can I select the correct
Device code?
A. Try to locate the correct Device Code that is similar to your device model number, as manufacturers
tend to use the same remote for a series of products.
A. Try to locate the correct Device Code for your A/V device, by testing the code one by one until most
keys work properly.
Q. My A/V equipment responds only to some of the commands.
A. You have set a code for which only some commands work properly but some do not. Try other codes
until most keys work properly.
A. You can learn the rest of the missing commands from your original remote, see Smart Learning section.
Q. Some learned commands in my remote RMX111 do not work.
A. Those commands are not learned properly. Try to teach your remote RMX111 again for those functions.
A. Check the batteries inside both A/V remote and your remote RMX111. If the batteries are weak, the
remote RMX111 cannot learn command properly. You have to replace all batteries for proper functioning.
If the RMX111 becomes locked, you will have to reset the remote to factory default set up which will erase
all your devices codes and unlock the RMX111. However, all codes can be backed up in advance on an
online facility.
(When you finished copying and teaching the original remote to your RMX111, you can upload your
RMX111 to your online database for future retrieval. Please connect your RMX111 with your PC, the
system will prompt an action automatically.)
Master Reset/Reset/Default
Master reset allows you to reset your RMX111 to its factory default state.
(After Master Reset, you have to setup the remote all over again. Before you do this, please make sure it is
really necessary.)
1. Remove the battery cover on the back side of your remote.
2. Make sure your RMX111 is loaded with fresh batteries.
3. Locate the mini USB connector inside the battery compartment.
4. Connect your RMX111 with the provided USB cable to your PC (via one of the available USB Ports).
5. Once, your RMX111 is connected to your PC, it will launch Internet Explorer browser to reach our
online database setup server. If your browser is not running after the connection of the RMX111 to
your PC, you have to double-click the icon(KRMAP.exe) on your desktop.
6. Follow Step 6 on Page 7.

FOR MORE INFORMATION PLEASE CONTACT
Follow us on:
Roksan Audio Ltd
Jubilee Close
Townsend Lane
London NW9 8TR
Tel: [phone] Fax: [phone]
Email: [email protected] Web: www.roksan.co.uk
Roksan Audio Ltd
User Manual
CLASSIFICATION: General Use Version: 1.07.2012
Allspecicationareliabletochangewithoutnotice.E&OE
http://facebook.com/roksan/
http://twitter.com/
http://goo.gl/NRtKc/
http://roksan.co.uk/