ROLA-CASE RSPEP User manual

2 PAN PHIL BOLTS
Screw Drivers Cordless Drill with
Torque settings
1 RSPEP/MDRF/
INSTALLATION MANUAL
RSPEP/MDRF/ (Mid Roof End Panel)
INCLUSIONS:
ATTENTION: PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLING/INSTALLING THIS PRODUCT
ANY ALTERATIONS, UNINTENDED OR UNAPPROVED WORK/USE OF THIS PRODUCT COULD CREATE A
HAZARDOUS CONDITION THAT CAN CAUSE DEATH, PERSONAL INJURY OR PROPERTY DAMAGE.
BEFORE YOU BEGIN:
•THE AVERAGE EXPECTED INSTALL TIME FOR THIS PRODUCT IS 10 MINUTES
•READ ALL THE INSTRUCTIONS BEFORE ASSEMBLY & INSTALLATION
•ALWAYS WEAR APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT, ESPECIALLY
EYEWEAR WHEN INSTALLING OUR PRODUCTS
•CONFIRM YOU HAVE ALL THE NECESSARY PARTS, TOOLS, EQUIPMENT, & TIME
REQUIRED BEFORE COMMENCING
WARNING
TOOLS REQUIRED:
ATTENTION
IMAGES USED IN THIS GUIDE MAY VARY SLIGHTLY DEPENDING ON YOUR MODEL
ALL DESIGN CONCEPTS ARE INTELLECTUAL PROPERTY OF ROLACASE AND ARE NOT TO BE COPIED, DISTRIBUTED OR COMMUNICATED TO UNAUTHORISED PARTIES
FOR TECHNICAL SUPPORT CALL: 1 [phone] / EMAIL: [email protected] / WEB: www.rolacase.com
All RolaCase/RolaShelf shelving products are to be used exclusively and in conjunc-
tion with RolaCase and RolaShelf shelving bays only. Failure to do so will cause the
shelving/products to perform in a nonfunctional manner and will void your warranty
ATTENTION
The RolaCase Mid Roof End Panel comes in 2 different options:
RSPEP/MDRF/L
(MID-LEFT END PANEL)
PART No. RSPEP/ - comes in 2 options:
• RSPEP/MDRF/R - Right Mid End Panel
• RSPEP/MDRF/L - Left Mid End Panel
Please note:
end panels come
in either a left or
right option
RSPEP/MDRF/R (MID-RIGHT END PANEL)
56.85”
18.1”
2 RSPEP-TOP HAT
REFER TO NEXT PAGE FOR FURTHER
INSTRUCTIONS
Left and Right
Mid Roof
End Panels
on a Ford Transit
2 NYLOC NUTS
12 SCREWS
18.1”
*Ideal for Mid/High Roof Vans
Ideal for Driver’s side Rear Ideal for Passenger’s side Rear
2 SELF TAPPING SCREWS

ALL DESIGN CONCEPTS ARE INTELLECTUAL PROPERTY OF ROLACASE AND ARE NOT TO BE COPIED, DISTRIBUTED OR COMMUNICATED TO UNAUTHORISED PARTIES
FOR TECHNICAL SUPPORT CALL: 1 [phone] / EMAIL: [email protected] / WEB: www.rolacase.com
ATTENTION: PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLING/INSTALLING THIS PRODUCT
ANY ALTERATIONS, UNINTENDED OR UNAPPROVED WORK/USE OF THIS PRODUCT COULD CREATE A
HAZARDOUS CONDITION THAT CAN CAUSE DEATH, PERSONAL INJURY OR PROPERTY DAMAGE.
WARNING ATTENTION
IMAGES USED IN THIS GUIDE MAY VARY SLIGHTLY DEPENDING ON YOUR MODEL
INSTALLATION MANUAL
RSPEP/MDRF/ (Mid Roof End Panel)
REV 6.1.1
For further details please go
to www.rolacase.com
Tip by default we
recommend aligning
the 3rd hole of the
End Panel with the
3rd hole of the posts.
Please note: this
may not be feasible
in some vehicles, if
this is the case it is
acceptable to use
neighbouring holes
Secure these
2x long screws
with nuts
First secure the top
hat bracket with
the posts using 4x
screws.
Secure these
2x screws last to
the End Panel and
the top hat bracket
A Begin by making sure you have the right end panel to suit your vehicle and
application
B Ensure your frames are installed and secured before proceeding
C Secure screws as illustrated on the next images
Sample of an
installed Mid
Roof End Panel
Tip we recommend
that the the 2 top hat
brackets are spaced
out equally to fully
support the Mid Roof
End Panel
Secure these holes
2x self tapping
screws