Roland JWX-30 Manual

JWX-30 Setup

What’s Included
NOTES:
All items included •Please be familiar with the
names of all the accessories
listed here.

What’s Included Cont.
NOTES:
All items included •Please be familiar with the
names of all the accessories
listed here.

JWX-30 Drivers Install
NOTES:
Driver Install
•Insert drivers CD.
•Click on Windows Driver and click Install.
•Follow setup guide for your Operating System.
V
p
anel Install:
p
•Click on Vpanel for JWX-30 and click Install.

Spindle Break In
NOTES:
Spindle will need to be broken in, or run in, under
the following conditions.
•When using spindle for the first time.
•After moving machine and reinstalling.
•After replacing the spindle unit.
•When used in low temperature area.
Break in or run in spindle in 3 steps.
•Ste
p
1
p
•Speed: 6,000 RPM
•Run Time: 20 minutes
•Step 2
•Speed: 15,000 RPM
•Run Time: 20 minutes
•Step 3
•
Speed: 30 000 RPM
•
Speed: 30
,
000 RPM
•Run Time: 20 minutes

Fixture’s Use
NOTES:
•The fixture used will be
determined by the object or
model created.

Setup Basics – Installing Tool
NOTES:
Follow the below steps for installing the collet,
tooling, and using the two spanner wrenches.
•Install the collet loosel
y
. Use the 17mm wrench to hold the
y
spindle in place as you install the collet until it is finger tight.

Setup Basics – Installing Tool
NOTES:
•Insert tool until it stops. There is a magnet inside the collet
that will “hold” the tool. Approximately 30 mm should be
extended out from the collet •To prevent tool from
accidental breaking, you can
place an item below the tool
should the tool accidentally fall.
•For example, a piece of wax.
•
Follow the same steps for the detection pin
•
Follow the same steps for the detection pin
.

Setup Basics – Installing Tool
NOTES:
•To tighten the collet, use both spanners to tighten the collet.
•TIP: Use the 17mm wrench in the left hand and 10mm
wrench in the right hand. Pull the wrenches away to
tighten
th ll t Ti ht t b t 3 2 N
f f
•These basic tool installation
steps will be used various
times during setup and the
tighten
th
e co
ll
e
t
.
Ti
g
ht
en
t
o a
b
ou
t 3
.
2 N
-m o
f f
orce.
model creation process.
•With time and practice, these
steps can be performed in a
few seconds.
•TIP: To loosen the collet, again with the 17mm wrench in
the left hand and 10mm in the right hand, pull the wrenches
towards each other
towards each other
.

Setup Square Clamp
NOTES:
What the square clamp will be used for
•Two sided cutting using
“
frame center”.
•Rotary cutting using
“
frame ti
p
”
p

Setup Square Clamp
NOTES:
Size Limitations for Small and Large Clamps
•Flat work area.

Setup Square Clamp
NOTES:
Size Limitations for Small and Large Clamps
•Rotary work area.

Setup Square Clamp
NOTES:
Installing and Setting Up Clamps
•Close front covers and press View button.
•O
p
en front cover and install detection
p
in.
pp
•Mount desired square clamp on Rotary Axis.
**Remove screw at tip of clamp**

Setup Square Clamp
NOTES:
•Install clamp holder and secure square clamp.

Install Detection Pin
NOTES:
•Insert detection pin until it stops. There is a magnet inside
the collet that will “hold” the pin. Approximately 30 mm
should be extended out from the collet.
Pin
•Use both spanners to tighten the collet.

Setup Square Clamp
NOTES:
•Close covers and open Vpanel for JWX-30.
•Located under programs & “Roland Vpanel for JWX-30”.
•Click on “Change Jig”.
•Select Square Clamp (Large) or Square Clamp (Small).

Setup Square Clamp
NOTES:
•Click on “Start Sensing” to begin the
detection process.
•JWX-30 will automatically detect
various points as well as turn the
various points as well as turn the
spindle by half a turn if needed. Click
“Close” when the process has
finished.
•Once finished, the jig will indicate
which jig is being used.
•JWX-30 is now ready setup for using
the small square fixture.

Setup Square Clamp
NOTES:
•Install material into clamp.
•Close covers and press “View” button to
move the table forward and make the
fixtures more accessible
fixtures more accessible
.
•Install 1mm ball end mill.

Setup Square Clamp
NOTES:
•You will be using SRP Player to “send”
the program to the JWX-30.
•Use the sides or frame center program
to perform this procedure
to perform this procedure
.
•Click on “Start Cutting” to begin.
•The software will indicate where you
need to set the origin point.
***
DO NOT CLICK
“
NEXT
”
YET
***
DO NOT CLICK NEXT YET

Setup Square Clamp
NOTES:
•Using the JWX-30 Virtual Panel, set the
origin point.
•Select “Set XYZ origin at frame center”
and click
“
Apply
”
and click Apply
.
•The tool will check the tool height and
set the correct X & Y origins at the
correct location.
•Once finished, the Vpanel will indicate
where the origin is set using a red
arrow on the fixture.