
SPECIFICATIONS
Nomina! input Level
MIC Input :-30 dBm
LINE IN Input: -10 dBm
Input Impedance
MIC Input; lOkQ
LINE Input: lOkfi
Nominal Output Level
-10 dBm (10 kfi Load Impedance)
Output Impedance
len
Recommended Load Impedance
200 nor greater
Connectors
MIDI Connectors (IN, OUT)
PHONES Jack (stereo miniature phone)
LINE IN jack (stereo miniature phone)
MIC Jack (mono miniature phone)
*Be sure to use audio cable which does not con-
tain aresister to connect to the PHONESjack or
the LINE IN jack.
Dimensions
250 (W) X40 (D) X28 (H) mm
9-7/8 (W) X1-5/8 (D) x1-1/8 (H) inches
Weight
96 g/4oz
Accessories
Owner's Manual
Mini Microphone
In the interest of product improvement, the speci-
fications of this unit are subject to change without
prior notice.
Beschelnigung des Herstellers/lmporteurs
-For Germany-
Hiermit wird bescheinigt. daB der/die/das
Connector Box MCB-3
(GerS!. Typ, Bezeichnung)
in Ubereinstimmung mit den Bestlmmungen der BMPT-A
AmtsbiVfg 243/1991, 46/1992 funk-enlst6rt iat.
Der vorschriftsmSBige Betrieb mancber Gerate (z. B.
MeBsender) kann atierdings gewissen Einschrankungen
unterliegen. Beachten Sie deshalb die Hinweise in der
Bedienungsanleitung.
Dem Zentralaml fiir Zulassungen im Fernmeldewesen
wurde das fnverkehrbringen dieses Gerates angezeigt und
die Berechtigung zur OberpKifung der Serie auf die
EinhaJtung der Bestimmungen eingeraumt.
Roland Corp6ration
4-16 Dojlmahama 1-Chome Kita-ku Osaka 530 Japan
(Name und Anschrifl des Herstellers/lmporteurs)
-For the USA-
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for aClass Bdigital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential
instaliation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instnjctlons. may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase ^e separation between the equipment and receiver.
-Connect the equipment into an outlet on acircuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class BLimit.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
For Canada-
CLASS BNOTICE
This digital apparatus does not exceed the Class Blimits for radio noise emissions set out in the Radio Interference
Regulations of the Canadian Department of Communications.
CLASSE BAVIS
Cet appareil num6rique ne depasse pas les Nmites de la classe Bau niveau des Amissions de bruits radioelectriques
fix6s dans le Reglement des signaux parasites par le minislfire canadien des Communications.