Roland V-Mixer M-200i User manual

1
Booting/Quitting the M-200i Remote
Booting the M-200i Remote
Turn on the power of the iPad where the M-200i Remote is installed and tap the following icon.
g.icon.eps
Quitting the M-200i Remote
Press the home button of the iPad to quit the M-200i Remote.
Connecting the M-200i and iPad
Right after turning the power on, M-200i cannot communicate with iPad via DOCK cable, Wired LAN nor Wireless LAN. Check the
status indicator located right upper corner of the M-200i’s display before connection.
Display Description
Communication with iPad is not ready.
Connected to the Wireless LAN router. The signal strength (the strength of the radio waves from the Wireless LAN router) is indicated by
three bars.
A wireless USB adapter is attached, but no connection to the Wireless LAN router is in eect.
No wireless USB adapter is attached.
Ad-hoc mode.
* For details of iPad network setup, refer to its user guide.
* For setting of the wireless LAN access point, refer to its owner’s manual.
Network setting of the M-200i
Carry out the network setting on the NETWORK screen of the M-200i. Call up the NETWORK screen using the following steps.
1. Call up the SETUP screen.
Press the [SETUP] in the M-200i’s DISPLAY section to call up the SETUP screen.
2. Call up the NETWORK screen.
Select [NETWORK] in the SETUP screen and press the [ENTER].
* For details of network settings of the M-200i, refer to its owner’s manual. Go to “Network“ section.
Types of Connection
There are 3 types of connection for the M-200i and iPad:
• Wired Connection using the Dock Cable (p. 2)
• Wired to Wireless Connection using a LAN Cable and Wireless LAN Access Point (p. 2)
• Wireless Connection using a Wireless USB Adaptor
- Wireless Network via a Wireless LAN Access Point (p. 3)
- Wireless Ad-Hoc Connection (p. 3)
M-200i Remote Setup Guide
Copyright © 2012 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written
permission of ROLAND CORPORATION.
* All product names mentioned in this document are trademarks or registered trademarks of their respective owners.
1PS

2
M-200i Remote Setup Guide
Wired Connection using the DOCK cable
Use the accessory dock cable to connect the M-200i’s DOCK CABLE connector and the iPad’s Dock connector.
g.dock-cable-connection.eps
The accessory DOCK cable is for the 30 pin Dock connector. If you are connecting the iPad equipped with such connector (1st, 2nd and 3rd
generation), use the accessory cable. If your iPad is equipped with Lightning connector (4th Generation or iPad mini), use the Lightning - 30 pin
conversion cable.
Stable communication is possible using the DOCK cable. Further, the cable is capable of the power supply to the connected iPad. You can carry out
the remote control operations without concerning the battery life.
When connection is made using the DOCK cable, operation sounds of iPad are sent to the M-200i depending on the patchbay setting.
The remote control application “M-200i Remote”produces the operation sounds while you are setting the clock or editing names using the software
keyboard. To turn o the operation sounds of the iPad, go to [Settings] and select [Sounds]. Then turn o [Lock Sounds] and [Keyboard Clicks].
Wired to WirelessConnection using a LAN Cable and Wireless LAN Access Point
Connect the M-200i to the wireless LAN access point (e.g., wireless LAN router) using LAN cable rst. Then wirelessly connect the
iPad and the wireless LAN access point.
g.wired-connect-router.eps
1. Connect the M-200i with the wireless LAN access point
Use LAN cable to connect the M-200i’s LAN connector and the wireless LAN access point.
2. Connect iPad to the wireless LAN access point
Select [Settings] > [Wi-Fi] > [Choose a Network] on the iPad and select the wireless LAN access point where the M-200i is
connected.

3
M-200i Remote Setup Guide
Wireless Connection using a Wireless USB Adaptor
Connect the wireless USB adaptor (WNA1100-RL ; sold separately) to the M-200i and make it ready to use the wireless LAN function.
Wireless Connection via a Wireless LAN Access Point
Wirelessly connect the M-200i to a wireless LAN access point, such as a router, rst. Then wirelessly connect with iPad via the
wireless LAN access point.
g.router-wireless.eps
Wireless USB Adaptor
（WNA1100-RL; sold separately）
1. Connect the wireless USB adaptor to the M-200i.
Connect the separately sold WNA1100-RL to the M-200i’s WLAN ADAPTOR connector.
2. Connect the M-200i and the wireless LAN access point wirelessly.
Select WPS or the wireless LAN access point and establish the wireless connection.
* For details of network settings of the M-200i, refer to the M-200i’s owner’s manual. Go to “Network - LAN Setting“ section.
3. Connect iPad to the wireless LAN access point.
Select [Settings] > [Wi-Fi] > [Choose a Network] on the iPad and select the wireless LAN access point where the M-200i is
connected.
Ad-Hoc Connection
Using Ad-Hoc, you can connect your iPad and the M-200i directly.
g.adhoc-connect.eps
Wireless USB Adaptor
（WNA1100-RL; sold separately）
The iPad connected in Ad-Hoc mode will be unable to communicate with the Internet or with another wireless device. However, an iPad that has
cellular capability will be able to connect to the Internet via the cellular connection. Please be aware that if you use a cellular connection for Internet
connectivity, you may incur costs depending on your rate plan.
1. Connect the wireless USB adaptor to the M-200i.
Connect the separately sold WNA1100-RL to the M-200i’s WLAN ADAPTOR connector.
2. Turn the M-200i’s Ad-Hoc mode to on.
To turn the Ad-Hoc mode on/o, refer to the M-200i’s owner’s manual. Go to“Network - Making detailed settings for WIRELESS LAN -
Connecting in ad-hoc mode (AD-HOC)” section.
3. Establish the connection between the iPad and the M-200i.
On the iPad, select the M-200i’s Ad-Hoc SSID. The SSID can be found on the M-200i in [Settings] > [Wi-Fi] > [Choose a Network]. As
the password screen appears, input Ad-Hoc key shown on the M-200i’s screen.

4
M-200i Remote Setup Guide
Select the M-200i to Remote Control
1. Open the ONLINE screen.
Tap the [ONLINE] as shown below to open the ONLINE screen. Scanning of available M-200i units starts.
g.online_button.eps
z
2. Select the M-200i unit to communicate.
When this software detects any available units, a list as shown below appears. Tap to select the target unit.
• The device name of the M-200i connected using the DOCK cable is shown as [Dock].
• Device names of the LAN connected M-200i units are shown in the list. If multiple units are connected via LAN, set a dierent wireless ID for each
unit.
* For details of setting the wireless ID, refer to the M-200i’s owner’s manual. Go to “Network - Making detailed settings for WIRELESS LAN - Making
the setting for WIRELESS ID”section.
g.select_device.eps
3. Start communication with the M-200i.
Tap or slide right the [Online] switch on the ONLINE screen. The iPad starts communication with the selected M-200i unit.
g.online_sw_o.eps

5
M-200i Remote Setup Guide
If an M-200i unit cannot be found
If this software cannot nd any available M-200i unit, the message “M-200i not found” is displayed. In this case or if you cannot nd
the device name of the target M-200i unit, tap [Refresh] button to rescan.
g.device_not_found.eps
Quit the Communication
Tap or slide left the [Online] switch on the ONLINE screen. The iPad quits communication with the selected M-200i unit.
g.online_sw_on.eps
Further, the following operations may terminate the connection.
• Suspending the application
• Switching to another application
• Connecting to the notication center
If you want to prohibit such operations from being triggered by multi-task gesture or auto lock, select the corresponding items in [Setting] of your iPad
and turn them o.

6
M-200i Remote Setup Guide
Synchronizing with the Controls on the M-200i
Tap or slide right the [Sync knob and switch] switch to start synchronizing with the controls on the M-200i unit. Using switches or
dials on the M-200i unit, you can control this software.
* For details of synchronizing feature, refer to the M-200i Remote’s owner’s manual. Go to “Synchronizing the M-200i Operations and the Display of
this Software“.
g.sync_sw_o.eps
Quit Synchronizing
Tap or slide left the [Sync knob and switch] switch to quit synchronizing.
g.sync_sw_on.eps
You can start/quit synchronizing while the communication between an iPad and the M-200i is active.