Roland V-Guitar System VG-99 User manual

®ÂØÒňή
Q&A
1
A collection of popular articles from the VG-99 knowledge base
©2009 Roland Corporation US
How Do I Connect the VG-99 to My System? ................................................... 2
How Do I Optimize the VG-99 for My Playing Style?.......................................... 3
How Do I Select a Patch? ............................................................................... 4
How Do I Set Up Effects? ............................................................................... 5
How Do I Set Up an Alternate Tuning? ............................................................. 6
How Do I Find VG-99 Articles in the RolandUS.com Knowledge Base?............... 7

2
®ÂØÒňή
VG-99
Ho w DoI Co n n e C t t H e VG-99 t o MySy S t e M ?
Confirm that the power is off on the VG-99.1
Connect one end of the 13-pin cable to the GK pickup.2
Connect the other end of the 13-pin cable to the GK IN jack on the VG-99.3
With a standard guitar or instrument cable, connect the L(MONO) MAIN OUTPUT on the VG-99 to the input of4
your amp, mixer, or PA. If you prefer, connect your headphones to the VG-99’s PHONES output.
Note: No modeling sound is produced at the GUITAR OUT on the VG-99. Use the GUITAR OUT to send your dry
guitar signal to a different amp if desired.
Now turn on the VG-99 and your amp.
5
How Do I Connect the VG-99 to My System?

3
®ÂØÒňή
VG-99
Ho w DoI op t I M I z e t H e VG-99 f o r Mypl a y I n G St y l e ?
Setting the sensitivity for the divided pickup is crucial for optimum playing results. Use the following steps to
adjust the pickup sensitivity to optimize the VG-99 for your playing style:
Press the SYSTEM button.
1
Press the PAGE left or right buttons to select page one.2
Press the F3 button (GK).3
Press PAGE4 3or 4to select Page 2.
Press F1 repeatedly to select the type of pickup that you have:
5 GK-3, GK-2A, PIEZO.
Press PAGE
6 4twice to select Page 4.
Play your high E string repeatedly with moderate force.
7
Turn the F1 knob while playing the string to adjust the sensitivity value so the box appears at the right side8
of the display.
Adjust the sensitivity for each of the remaining strings using the F2-F6 knobs.
9
Tip: For additional details about further adjustment of the GK settings, refer to Pages 21and 22 in the VG-99
manual
.
Press EXIT twice when you’re finished.
10
How Do I Optimize the VG-99 for My Playing Style?

4
®ÂØÒňή
VG-99
Ho w DoI Se l e C t apa t C H ?
There are 200 Preset and 200 User Patches in the VG-99. Here’s how to select them:
Turn the PATCH/VALUE dial to select a patch.
1
To select patches by category:
Press CATEGORY.
1
Press F1 or F2 to select the desired category.2
Turn the PATCH/VALUE dial or press F3 or F4 to select a patch.3
How Do I Select a Patch?

5
®ÂØÒňή
VG-99
Ho w DoI Se t Upef f e C t S ?
Changing the order of the effects is done within the Chain section of the VG-99. Positioning an effect before or
after another can significantly change the sound character of a patch. Use the following steps to move an effect
within the chain:
Select a patch to edit.
1
Press CHAIN.2
Press the F2 or F3 button to select the effect you want to move.3
Press F4 or F5 to move the selected effect to a new location.4
Repeat Steps 3 and 4 for any other effects you want to move.5
Press EXIT when you’re finished.6
How Do I Set Up Effects?