Roland JUNO-106 User manual

© 2021 Roland Corporation© 2021 Roland Corporation
0101
Parameter Guide
JUNO-106
Model Expansion

1
2 3 4 5
6 7 8
9
This document explains about the parameters and setting screens for the ZENOLOGY Pro
Model Expansion.
The parameter names, the order in which they appear and other information may dier,
depending on the product.

1 SystemSystem
CONDITION
Simulates the changes that occur as a unit ages.
PITCH DRIFT
Adjusts the slight pitch drift that occurs when notes are
played on an analog synthesizer.
KEY MODE
[SOLO] button
Sound is produced monophonically.
[POLY] button
Sound is produced polyphonically.
[UNISON] button
Sound is produced in unison.
[SL-UNISON] button
Sound is produced in monophonic unison.
PORTAMENTO [OFF] [ON] button (PORTA MODE/PORTA TIME)
Selects whether portamento is applied to the performance and species the
portamento time.
PORTA CRV
[ORIG] button
Change according to the original
curve of the model.
[LIN] button
Change in a linear curve.
[EXP-1] button
Change in a non-linear curve (gentle
slope).
[EXP-2] button
Change in a non-linear curve (steep
slope).
[PRM EXP] button
(PARAM EXPANSION)
If this is ON, the range of the LFO
RATE, CUTOFF, RESONANCE, and
FILTER ENV DEPTH parameters are
extended beyond the range of the
original model.

2 LFOLFO
[RATE] knob (LFO RATE)
Species the rate of the LFO cycle.
[DELAY TIME] knob (FLO DELAY TIME)
Adjusts the time from when the key is pressed until the
LFO starts to apply modulation.

3 DCODCO
PWM
PM MODE = LFO: Adjusts the modulation depth.
PM MODE = MANUAL: Adjusts the pulse width.
[LFO] [MAN] button (PW MODE)
Selects whether the pulse width is modulated by the LFO
(LFO) or kept at the xed value specied by PULSE WIDTH
MOD (MANUAL).
[ (PWM wave)] button (PW SWITCH)
Turns the PWM wave on/o.
[ (Sawtooth wave)] button (SAW SWITCH)
Turns the sawtooth wave on/o.
[RANGE] knob (OSC RANGE)
Species the octave of the oscillator.
16’, 8’, 4', 2’
LFO (OSC LFO MOD)
Uses the LFO to vary the pitch (vibrato).
USUB (SUB LEVEL)
Adjusts the volume of the sub oscillator.
NOISE (NOISE LEVEL)
Adjusts the volume of the noise.

4 HPFHPF
[FREQ] knob (HPF STEP)
Sets the high-pass lter’s cuto frequency in four steps.
0, 1, 2, 3

5 VCFVCF
[R] [M] [S] buttons (VINTAGE FLT TYPE)
If a vintage type model is selected, these buttons change the type of lter.
[R] models a Roland lter, and [M] and [S] model vintage synthesizers made by
other companies.
[FREQ] knob (CUTOFF)
Species the cuto frequency of the low-pass lter.
The frequency region above the cuto frequency is cut,
producing a more mellow tonal character.
[RES] knob (RESONANCE)
Boosts the region of the lter’s cuto frequency. Higher
values produce a stronger result, giving the sound a
distinctively synthesizer-like character.
Polarity buttons
Specify the polarity of the lter.
ENV (FLT ENV DEPTH)
Adjusts the amount by which the cuto frequency is
controlled by the envelope.
LFO (FILTER MOD)
Adjusts the amount by which the LFO modulates the
cuto frequency.
KYBD (FLT KEY FOLLOW)
Adjusts the amount by which the keyboard pitch aects
the cuto frequency (key follow). With smaller values, the
cuto frequency becomes lower as you play higher notes.

6 VCAVCA
[LEVEL] knob (AMP LEVEL)
Adjusts the volume of the tone.
[ENV] [GATE] button (AMP ENV SEL)
Species whether the volume is controlled by the ENV
(ENV) or by the gate signal (GATE).

7 ENVENV
Envelope
You can edit the ADSR settings of the envelope.
AD
SR
[A] knob (ENV ATTACK)
Adjusts the Attack time.
[D] knob (ENV DECAY)
Adjusts the Decay time.
[S] knob (ENV SUSTAIN)
Adjusts the Sustain level.
[R] knob (ENV RELEASE)
Adjusts the Release time.

8 MFXMFX
MFX parameters
The edit screen is dierent for each MFX type.
[MFX] button
Turns MFX on/o.
[MFX TYPE] indication
Shows the currently selected
MFX name.
[MFX LEVEL] knob
Adjusts the MFX output level.