rollease acmeda Automate Paradigm User manual

AUTOMATE™
Paradigm Flush Wall Switch
FEATURES:
• Multi channel selectable
• Retrofit Ready
• Group Control
• Compatible with screwless decorator cover plates
• Optionally functions as handheld remote
AUTOMATE™| Paradigm flush wall switches feature a contemporary design and a
wirefree deployment, making them retrofit ready for any location. Paradigm 5 channel
switches are perfect for individual shade, room and whole home control.
The Paradigm flush mount switch can be mounted on top of any surface. Its slim profile
eliminates the need for any holes to be cut in walls.
MTRF-WS5-FLUSH_PRGM_v1.4 MAY 2021
433 MHz

2 | Automate™Programming Instructions | Flush Wall Switch ROLLEASE ACMEDA
1 TECHNICAL DATA / PACK CONTENTS 3
2 SAFETY 4
3 INSTALLATION 5
3.1 Kit Components 5
3.2 Install switch batteries 5
3.3 Magnetic Wall Clip 6
3.4 Fixed Wall Clip 6
4 FUNCTIONAL OVERVIEW 7
4.1 Buttons 7
4.2 Selecting a channel 7
5 PROGRAMMING 8
5.1 Using motor P1 button 8
5.2 Using pre-existing controller 9
6 INITIAL SET UP 10
6.1 Check motor direction 10
6.2 Set Limits 10
6.3 Locking the limit setting function 11
7 ADJUSTING LIMITS 12
7.1 Adjust upper limit 12
7.2 Adjust lower limit 12
8 FAVORITE POSITIONING 13
8.1 Set a favorite position 13
8.2 Send shade to favorite position 13
8.3 Delete favorite position 13
9 TROUBLE SHOOTING 14
NOTES 15
CONTENTS

ROLLEASE ACMEDA Automate™Programming Instructions | Flush Wall Switch | 3
1 TECHNICAL DATA / PACK CONTENTS
TECHNICAL SPECIFICATIONS
Voltage: 3V (CR2430)
Frequency: 433.92 MHz
Transmitting Power: Less than 10mW
Ambient Operating Temperature: -10°C [°F] -50°C [122°F]
Transmission Distance: 20m - 100m [65' - 328'] (open space)

4 | Automate™Programming Instructions | Flush Wall Switch ROLLEASE ACMEDA
2 SAFETY
WARNING: Important safety instructions to be read before installation and use.
Incorrect installation or use can lead to serious injury and will void manufacturer's liability and warranty. It is important for the
safety of persons to follow the enclosed instructions.
Save these instructions for future reference.
• Do not expose to water, moisture, humid and damp
environments or extreme temperatures.
• Persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, should
not be allowed to use this product.
• Use or modification outside the scope of this instruction manual
will void warranty.
• Installation and programming to be performed by a suitably
qualified installer.
• Follow installation instructions.
• For use with motorized shading devices.
• Frequently inspect for improper operation.
• Do not use if repair or adjustment is necessary.
• Keep clear when in operation.
• Replace battery with correctly specified type.
FCC & ISED Statement
WARNING: Do not ingest battery, Chemical Burn Hazard.
This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from
children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Caution: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user's authority
to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequencyenergy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
FCC ID: 2AGGZMTRFWS5FLUSH
ID: 21769-MTRFWS5FLUS
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

ROLLEASE ACMEDA Automate™Programming Instructions | Flush Wall Switch | 5
3.1 Kit Components
3.2 Replace Battery
3 INSTALLATION
1. 1 x Cover
2. 1 x Switch Remote
3. 1 x Magnetic Wall Clip
4. 1 x Fixed Wall Clip
5. 2 x Pan Head Screw
6. 2 x Phillips Head Screw
7. 2 x Wall Plug
8. 3V - CR2430 Battery
9. Programming Manual
10. 1x Small Phillips Head Screw
- Battery Cover
11. 1x PH0 Screw Driver
10.11.
Open rear battery cover by
gently separating switch
covers with a screwdriver
Remove Screw Install CR2430 battery with
positive side facing up. Snap
covers back together.
Insert and fasten
screw
Snap covers back together.
NEW REMOTE STARTUP
Remove Battery Isolation Tab
Before you can use remote,
REPLACE BATTERY
Images shown for illustrative purposes
Insert and fasten screw with screwdriver
provided.
Remove the cover screw
Replace battery as required
Ensure to re-insert and fasten the screw
afterwards
IMPORTANT
FOR CHILD SAFETY, SCREW MUST BE USED
AT ALL TIMES TO SECURE BATTERY COVER
IN PLACE.
Battery
Battery
Battery
NEW REMOTE STARTUP
Remove Battery Isolation Tab
Before you can use remote,
REPLACE BATTERY
Images shown for illustrative purposes
Insert and fasten screw with screwdriver
provided.
Remove the cover screw
Replace battery as required
Ensure to re-insert and fasten the screw
afterwards
IMPORTANT
FOR CHILD SAFETY, SCREW MUST BE USED
AT ALL TIMES TO SECURE BATTERY COVER
IN PLACE.
Battery
Battery
Battery
NEW REMOTE STARTUP
Remove Battery Isolation Tab
Before you can use remote,
REPLACE BATTERY
Images shown for illustrative purposes
Insert and fasten screw with screwdriver
provided.
Remove the cover screw
Replace battery as required
Ensure to re-insert and fasten the screw
afterwards
IMPORTANT
FOR CHILD SAFETY, SCREW MUST BE USED
AT ALL TIMES TO SECURE BATTERY COVER
IN PLACE.
Battery
Battery
Battery
NEW REMOTE STARTUP
Remove Battery Isolation Tab
Before you can use remote,
REPLACE BATTERY
Images shown for illustrative purposes
Insert and fasten screw with screwdriver
provided.
Remove the cover screw
Replace battery as required
Ensure to re-insert and fasten the screw
afterwards
IMPORTANT
FOR CHILD SAFETY, SCREW MUST BE USED
AT ALL TIMES TO SECURE BATTERY COVER
IN PLACE.
Battery
Battery
Battery
NEW REMOTE STARTUP
Remove Battery Isolation Tab
Before you can use remote,
REPLACE BATTERY
Images shown for illustrative purposes
Insert and fasten screw with screwdriver
provided.
Remove the cover screw
Replace battery as required
Ensure to re-insert and fasten the screw
afterwards
IMPORTANT
FOR CHILD SAFETY, SCREW MUST BE USED
AT ALL TIMES TO SECURE BATTERY COVER
IN PLACE.
Battery
Battery
Battery
Note:
On Startup, Remove Battery
isolation tab (remove cover
screw if needed).
Battery
Isolation Tab
1.5. 2. 6.8. 3. 7. 4.

6 | Automate™Programming Instructions | Flush Wall Switch ROLLEASE ACMEDA
3.4 Fixed Wall Clip
Best Practice Tip:
Program the Switch to the motor prior to installation, then test radio performance in the location the switch
will be installed in, to ensure best performance.
Slide the Switch onto the Wall Clip.
Use supplied fasteners and anchors as needed to attach the base and cover.
Switch is secured unless the Cover is removed.
Safely dispose of the unused Magnetic Wall Clip.
3.3 Magnetic Wall Clip
Best Practice Tip:
Program the Switch to the motor prior to installation, then test radio performance in the location the switch
will be installed in, to ensure best performance.
Use the Magnetic Wall Clip if you require the remote to be easily detachable.
Use supplied fasteners and anchors as needed to attach the base and cover.
Switch is held in position magnetically and can be removed as desired.
Safely dispose of the unused Fixed Wall Clip.
Use the Fixed Wall Clip if you require the remote to be non-removable.

ROLLEASE ACMEDA Automate™Programming Instructions | Flush Wall Switch | 7
Press desired channel button(s) To deselect channel, press channel button
until LED turns off
4.1 Buttons
4.2 Selecting a channel
4 FUNCTIONAL OVERVIEW
Motor Response
Switch requires that at least one channel be selected at
all times. First select an additional channel, then deselect
channel you don't want to operate.
Blue LEDs will illuminate indicating channel selection.
IMPORTANT
CHANNELS 1-5
STOP
P2
UP DOWN

8 | Automate™Programming Instructions | Flush Wall Switch ROLLEASE ACMEDA
Approx.
Approx.
5.1 Using motor P1 button
5 PROGRAMMING
Multiple motors can be grouped onto shared channels for co-ordinated control. Limit settings and favorite positions cannot be adjusted when
motors are grouped together.
• Confirm that motor limits and favorite position are already set for each individual motor.
• Ensure that each motor you want to group is also assigned to another channel by itself
IMPORTANT
Select a channel on
switch.
Hold P1 button on motor
head.
Hold STOP on switch.
Motor ResponseMotor Response
RELEASE P1

ROLLEASE ACMEDA Automate™Programming Instructions | Flush Wall Switch | 9
5.2 Using pre-existing controller
A = Existing switch or channel (to keep)
B = Switch or channel to add or remove
Select channel that
operates motor on
existing switch.
Press P2
Press P2 a second time on
existing switch.
Select desired channel on
new switch. Press P2 on
new switch.
Motor response Motor response Motor response

10 | Automate™Programming Instructions | Flush Wall Switch ROLLEASE ACMEDA
.
6.1 Check motor direction
Damage to shade may occur when operating motor prior to
setting limits. Attention should be given.
Reversing motor direction using this method is only possible
during initial set-up
Direction change will not occur if switch is locked.
See Section 6.3.
To check travel direction of shade, press UP or
DOWN on controller.
Quick Press = Step
Long Press = Continuous Travel
To reverse shade direction, hold both UP and
DOWN.
Until the motor responds.
Approx.
Motor Response
IMPORTANT
IMPORTANT
6 INITIAL SET UP
SECS
5
6.2 Set Limits
Cycle shade up and down prior to setting limits to settle fabric
For FT Motors, the bottom limit should be set ~ 1.38 in. (35mm) below the Ultra-Lock to disengage the auto lock mechanism when the shade is
raised.
After setting limits, motor will automatically exit from initial
set-up mode.
Move shade to the desired highest or lowest
position by pressing the UP or DOWN buttons
on controller.
To save upper limit, hold UP and STOP.
To save lower limit, hold DOWN and STOP.
Motor Response
IMPORTANT
IMPORTANT
Initial set-up is not complete
IMPORTANT
Approx.

ROLLEASE ACMEDA Automate™Programming Instructions | Flush Wall Switch | 11
6.3 Locking the limit setting function
Press STOP and hold
for 15 seconds
Press STOP and hold
for 15 seconds
Release STOP
button.
Locked limit
settings
All lights flash x 1 All lights flash x 2
Release STOP
button.
Unlocked limit
settings
Stops unwanted changes to limit settings
Approx. Approx.
Remote Response Remote Response
5 5
The locked setting will prevent any multi-button functions. These include reversing direction before setting limits, limit setting and toggling
between tilt and roller modes.
IMPORTANT

12 | Automate™Programming Instructions | Flush Wall Switch ROLLEASE ACMEDA
SEC
SEC
S
S5
5
7.1 Adjust upper limit
7.2 Adjust lower limit
Hold UP and STOP on
controller.
Hold DOWN and STOP
on controller.
Move shade to the desired
lowest position by pressing
the DOWN button.
Move shade to the desired
highest position by pressing
the UP button.
To save upper limit, hold UP
and STOP.
To save lower limit, hold
DOWN and STOP.
Approx.
Approx.
Motor Response
Motor Response Motor Response
Motor Response
7 ADJUSTING LIMITS
SEC SECS S
5 5
Approx. Approx.
For FT Motors, the bottom limit should be set ~ 1.38 in. (35mm) below the Ultra-Lock to disengage the auto lock mechanism when the shade is
raised.
IMPORTANT

ROLLEASE ACMEDA Automate™Programming Instructions | Flush Wall Switch | 13
8.1 Set a favorite position
8.2 Send shade to favorite position
8.3 Delete favorite position
Press P2 on controller. Press STOP on controller. Press STOP on controller.
Move shade to the desired position by pressing the UP or DOWN button on the controller.
Press P2 on controller. Press STOP on controller. Press STOP on controller.
Approx.
Motor Response
Motor Response
Motor Response
Motor Response
Motor Response
Motor Response
8 FAVORITE POSITIONING
CHANNELS 1-5
STOP
P2
UP DOWN
CHANNELS 1-5
STOP
P2
UP DOWN

14 | Automate™Programming Instructions | Flush Wall Switch ROLLEASE ACMEDA
9 TROUBLE SHOOTING
Problem Cause Remedy
Switch battery is discharged Replace battery
Motor is not responding
Battery is inserted incorrectly Check battery polarity
Radio interference / Shielding
Ensure remote is positioned away
from metal objects and that aerial on
motor or receiver is kept straight and
away from metal.
Receiver distance is too far
from remote
Move remote to a closer position or
consider a repeater for improved
performance.
Power failure Check power supply to motor is
connected and active.
Incorrect motor wiring
Check wiring is connected correctly
(refer to motor installation
instructions).
Cannot set limits on a single
motor (multiple motors
respond)
Using channel 0 to adjust
motor limits
(Multi channel remote ONLY)
Always reserve an individual channel
for programming functions.
SYSTEM BEST PRACTICE - Provide
an extra 15 channel remote in your
multi motor projects, that provides
individual control for each motor for
programming purposes.
Motor will not go down after
setting the top limit.
Top limit was set using the
DOWN and STOP buttons.
Reset the motor and begin
programming sequence again.
Remember that upper limit is to be
set using the UP and STOP buttons,
and the down limit is set using the
DOWN and STOP buttons.
Motor will pair, but can not set
limits.
Switch is in a locked state.
Control must be unlocked
to set limits or perform any
multi-button functions.
Press and hold STOP button for 15
seconds, until locked state changes.

ROLLEASE ACMEDA Automate™Programming Instructions | Flush Wall Switch | 15
NOTES

16 | Automate™Programming Instructions | Flush Wall Switch
ROLLEASE ACMEDA
AUSTRALIA
110 Northcorp Boulevard,
Broadmeadows VIC 3047
T [phone] | F [phone]
ROLLEASE ACMEDA
USA
750 East Main Street, 7th Floor
Stamford, CT 06902
T [phone] | F [phone]
ROLLEASE ACMEDA
EUROPE
Via Conca Del Naviglio 18, Milan
(Lombardia) Italy
T [phone] | F [phone]
Queensland Branch
Unit 2/62 Borthwick Avenue,
Murarrie QLD 4172
[e-mail]
rolleaseacmeda.com