Roller Grill CSE 350 Technical manual

INSTRUCTIONS FOR USE AND INSTALLATION
ELECTRIC CREPE MACHINES
CSE 350 / CSE 400 / CDE 350 / CDE 400
Made in France
December 2011

19

18
Nomenclature CDE 400
Spare parts CDE 400
Rep Code Qty Pièce Spare part
1B02049 2Disque émaillé diam 400 Enamelled cast iron plate 400
2D02163 2Résistance blindée Armoured heating element
367049 2Serre résistance diam 400 Heating element holder 400
467048 2Tôle protection Protecting S/steel
5A16014 1Bornier 6 plots Six holes domino
668038 1Plateau disque Griddle plate
768039 1Ceinture Casing
8A13017 4Pied Foot
9F05017 1Râteau en bois Wooden scraper
10 68040 1Fond socle Bottom casing
11 A08009 2Voyant vert Green pilot light
12 C01010 1Cable Cord
13 A10032 1Presse étoupe 16 Cord closer 16
14 68034 4Renfort disque Plate holder
15 68041 1Bandeau Control panel
16 A08003 2Voyant orange Orange pilot light
17 A06042 2Thermostat Thermostat
18 A14113 2Bouton 9 HKnob 9 H
19 A01020 2Commutateur Commutator
ELECTRIC CREPE MACHINES
CSE 350 / CSE 400 / CDE 350 / CDE 400
Congratulations for the acquisition of this upmarket appliance made in France. You
chose an appliance which alloys the best technical qualities with a big user-
friendliness. We wish you the biggest contentment
1. SECURITY INSTRUCTIONS
Please respect these instructions scrupulously to avoid any risk of fire, electric shock,
scald or other wounds and damage. During the use of this appliance, fundamental cir-
cumspection of security must always be noticed, such as:
-Take into account the instructions to be systematically kept with the appliance.
-Install the appliance always in instructions respect. A 10 cm distance minimum
with the partition or the wall is necessary.
-This appliance is marked out for outside use or inside use in a well ventilated
room or under a cooker hood
-Protect the appliance from direct light of the sun, frost and humidity.
-Never leave the appliance within the reach of children or disabled persons with-
out surveillance.
-Never move the appliance when it is working or when the cooking surface is still
hot.
-Check that the appliance is definitely off before connecting it up or disconnecting
it.
-Do not touch the hot surfaces of the appliance. The temperature of the hot sur-
faces can be very important when the appliance is working. Always use handles
and control knobs.
-Do not use the appliance for other functions than determined use.
-Do not leave the cord of electrical feeding in the contact of hot surfaces.
-The appliance should not be used close to combustible materials.
-During use, look after not to obstruct hearings of aeration of the appliance
-To avoid any electric shock, never plunge the appliance, the cord or plug in water
or quite other liquid.
-If the cord is harmed, it must be replaced by the producer, his after sale service
or persons of similar skills to avoid any risk.
-Entrust compensations only to a skilled person.
-Use only spare parts of origin.
-At the end of cooking, before cleaning the appliance, do not forget to disconnect
it.
2. CONTENTS OF CARDBOARD PACKAGING
Device: a crepe machine
Accessories: - A wooden crepe rake
-The present note
See exploded views for CSE 350/CSE 400/CDE 350/CDE 400 at the end of the docu-
ment. 3

3. CONFORMITY OF USE
Use the device only to cook crepes, pancakes, buckwheat cakes...
4. WAY OF FUNCTIONING
This crepe machine is a strong cooktop in enamelled cast iron. The strong thickness
of the plate ensures an excellent homogeneity and a stability of the temperature.
The plate’s smooth surface provides direct heat transfer to the food being cooked,
without heat loss at the centre as in the periphery thanks to spiral heating element
integrated under the cast iron plate that cover the entire cooking surface.
To turn on and preheat the plate, just turn the thermostat control knob (n°2 on pic-
ture) on the wished position. The orange pilot light ignites (n°3 on picture), the crepe
machine is heating. When orange pilot light switches off, the device is ready for the
cooking.
During cooking, the temperature can be regulated thanks to thermostat control knob
(n°2 on picture) to avoid phenomenon of overheating. Orange pilot light (n°3 on pic-
ture) indicates heating periods.
A crepe is cooked at a temperature around 200-220°C (position 5-6)
On/off pilot light Thermostat
Thermostatic pilot light 4
12
12
3
317

16
Nomenclature CDE 350
Spare parts CDE 350
Rep Code Qty Pièce Spare part
1B02016+PERCAGE 2Disque émaillé diam 350 Enamelled cast iron plate 350
2D02013 2Résistance blindée Armoured heating element
367042 2Serre résistance diam 350 Heating element holder 350
466019 2Contre disque Gridle holder
5A16014 1Bornier 6 plots Six holes domino
668044 1Plateau disque Griddle plate
768039 1Ceinture Casing
8A13017 4Pied Foot
9F05017 1Râteau en bois Wooden scraper
10 68040 1Fond socle Bottom casing
11 A08009 2Voyant vert Green pilot light
12 C01010 1Cable Cord
13 A10032 1Presse étoupe 16 Cord closer 16
14 68034 1Renfort disque Plate holder
15 68041 1Bandeau Control panel
16 A08003 2Voyant orange Orange pilot light
17 A06042 2Thermostat Thermostat
18 A14113 2Bouton 9 HKnob 9 H
19 A01020 2Commutateur Commutator
5. FUNCTIONING / MANIPULATION
a) Installation / assembly:
-Unpack carefully the device of its packaging.
-Place it on a plane and heatproof surface.
-Never place the device near a wall or near a partition makes of combustible materials
even if it is very well isolated.
-A distance of minimum 10 cm with the partition or the wall is necessary.
b) First starting:
Before the first use, remove the anti-corrosion protection fat with a cleaner and a wet
sponge.
During the first use, grease your plate with oil and preheat the crepe machine during
about 15 min. Once preheating is finished, set the thermostat on the wished tempera-
ture.
First cleaning
Clean the device before the first use. (See 6. Cleaning)
Connection of the device
-Check that the tension and the frequency of the electricity network suit to the values
indicated on the descriptive plate.
-Make sure that every control knob is positioned on 0.
-Check that neither the cord nor the plug are damaged
-Unwind completely the electric power cable and connect it in a plug connected with
the earth.
-The device is connected.
NB: in case of connection of the device in a plug without earth protection or directly on
the electricity network, confide its connection to a qualified person .
c) Use of device :
Elements of command and display
Command/Display Function
Thermostat (n°2 on picture) On/off + Temperature setting
Orange pilot light
(n°4 on picture) Machine is heating (pilot light on) Temperature reached (pilot light off)
Green pilot light (n°1 on pic-
ture) Machine is on (pilot on) Machine is off (pilot off)
5

6
Putting on
Turn on the thermostat control knob (n°2 on picture) on the wished position: the
green pilot light (n°1 on picture) ignites: the machine is on. And the orange pilot
light (n°3 on picture) ignites. The machine is warming up. Once orange pilot light
(n°3 on picture) is off, the machine reached the wished temperature. Grease the
plate before each cooking.
Temperature setting
Set the temperature by positioning the thermostat (n°2 on picture) to the desired
temperature. The orange pilot light (n°3 on picture) switches on if a higher level of
temperature is required and switches off when the same is reached.
It is not necessary to leave the device switched on at full power. It is necessary
to adapt the temperature to products to be cooked to limit the energy consump-
tion.
Stopping the appliance
Set thermostat control knob (n°2 on picture) on 0: the appliance is no longer func-
tioning.
Let the device cool
Disconnect the power cable.
Clean the appliance. (see 6. Cleaning)
During non-prolonged use, we recommend you to grease the plate
d) Breakdown / repair:
In case of breakdown or of damaged part, please call your after-sales service and
confide any technical operation to qualified person.
When you contact the after-sales service of your distributor or your store, give him the
complete reference of your device (commercial name, type and serial number). This
information appears on the visible descriptive plate behind the device.
6. CLEANING AND MAINTENANCE
Disconnect the device.
-Let cool completely the device before any technical intervention or cleaning.
-Clean your crepe machine regularly after each use to avoid phenomenon of cala-
mine coming the cooking of the sugar and from some dough which accumulates very
quickly, and creates a film on the plate which harms in the quality of the cooking.
15

14
Nomenclature CSE 400
Spare parts CSE 400
Rep Code Qty Pièce Spare part
1B02049 1Disque émaillé diam 400 Enamelled cast iron plate 400
2D02163 1Résistance blindée Armoured heating element
367049 1Serre résistance diam 400 Heating element holder 400
467048 1Tôle protection Protecting S/steel
5A16013 1Bornier 3 plots Three holes domino
668030 1Plateau disque Griddle plate
768031 1Ceinture Casing
8A13017 4Pied Foot
9F05017 1Râteau en bois Wooden scraper
10 68032 1Fond socle Bottom casing
11 A08009 1Voyant vert Green pilot light
12 C03007 1Cordon avec prise Cord with plug
13 A10032 1Presse étoupe 16 Cord closer 16
14 68034 2Renfort disque Plate holder
15 68033 1Bandeau Control panel
16 A08003 1Voyant orange Orange pilot light
17 A06042 1Thermostat Thermostat
18 A14113 1Bouton 9 HKnob 9 H
19 A01020 1Commutateur Commutator
- For cleaning, only use non-abrasive products, clean regularly the external walls of
your device with warm water and wash liquid: avoid the abrasive towelling. Rinse your
device with a wet sponge. Dry it with a soft cloth
-Never clean the device under a water jet, the infiltrations would risk to damage it in a
irreparable way.
-Never immerse the device, the cord or the plug in the water or quite other liquid to
avoid any electric shock.
-During a prolonged non-use, we recommend you strongly to keep the device
shielded from the humidity and to grease the plate.
7. TECHNICAL SPECIFICATIONS
Wires colours correspondence Phase 1Brown
Phase 2Black
Phase 3Grey
Neutral Blue
Earth Yellow-Green
The equipotential connection marked by this symbol must be linked with the
equipotential conductive connection of your installation by means of a minimum con-
duction of a 2.5 mm² section.
8. NORMS AND LEGALS DISPOSALS
The device is conform to :
IEC/EN 60335-1
IEC/EN 60335-2-38
EN 55014-1 + 55014-2
EN 61000-3-2 + 61000-3-3
Models CSE 350
Outside dimen-
sions mm 450x500x240
Weight 14.5 Kg
Power 3000 W
Voltage 220-240 V N~
No element 1
Current 13 A
CSE 400
450x500x240
18 Kg
3600 W
1
15.7 A
220-240 V N~
CDE 350
860x500x240
29 Kg
6000 W
2
13 A/Phase
380-415 V 3
N~
CDE 400
860x500x240
34 Kg
7200 W
2
15.7 A/Phase
380-415 V 3 N~
7

9. ELIMINATION OF THE ELECTRIC AND ELECTRONIC WASTE
The device respects the directives:
2002/96/CE ( DEEE) N°34270064800021
2002/95/CE ( ROHS)
2006/95 CE
2004/108 CE
Reach rule
Never put the device among household waste.
The device must be put down in a centre of recycling for the electric equipments.
The materials of the device are indeed reusable. By eliminating correctly the electric
and electronic wastes, the recycling and quite other shape of re-use of worn equip-
ments, you participate in a significant way in the environmental protection.
For any information about the collection of electric and electronic waste, please con-
tact your distributor.
10. GUARANTEE
Conditions of guarantee
The guarantee applicable to any device is the commercial guarantee of the distributor
or the retailer. Please contact the store where you bought your device to know the
precise conditions.
The guarantee grants no right for damages.
The dispositions which follow are not exclusive of the profit of the legal guarantee
planned by articles 1641 and following ones of the Civil code relative to the defects
and the latent defects.
Exclusion clauses of the guarantee
Bad installation and bad maintenance, in particular if they do not respect cur-
rent regulations or instructions appearing in this user guide.
Cannot benefit from the guarantee the repairs required as a result of false operations,
of inappropriate use, of carelessness or of excess loads of the device, as well as
those resulting from variations of the power supply, over tension or from defective in-
stallations.
The damage due to shocks, bad weather is not flatware by the guarantee. The mate-
rial travels at the risks of the user; in case of delivery by carrier, the consignee has to
have reservations towards the carrier before any delivery of the device. 813

12
Nomenclature CSE 350
Spare parts CSE 350
Rep Code Qty Pièce Spare part
1B02016+PERCAGE 1Disque émaillé diam 350 Enamelled cast iron plate 350
2D02013 1Résistance blindée Armoured heating element
367042 1Serre résistance diam 350 Heating element holder 350
466019 1Contre disque Griddle holder
5A16013 1Bornier 3 plots Three holes domino
668043 1Plateau disque Griddle plate
768031 1Ceinture Casing
8A13017 4Pied Foot
9F05017 1Râteau en bois Wooden scraper
10 68032 1Fond socle Bottom casing
11 A08009 1Voyant vert Green pilot light
12 C03007 1Cordon avec prise Cord with plug
13 A10032 1Presse étoupe 16 Cord closer 16
14 68033 1Bandeau Control panel
15 A08003 1Voyant orange Orange pilot light
16 A06042 1Thermostat Thermostat
17 A14113 1Bouton 9 HKnob 9 H
18 A01020 1Commutateur Commutator
The guarantee comes to an end in case of intervention, of repair, of modification by
no qualified persons, or of use in inappropriate purposes.
9

10 11