Rolls Rack Power Module RPM26 User manual

R
PM26
Rack Power Module
OWNERS MANUAL
LIMITED WARRANTY
This product is warranted to the original consumer purchaser to be free from
defects in materials and workmanship under normal installation, use and service for a
period of one (1) year from the date of purchase as shown on the purchaser’s receipt.
The obligation of Rolls Corporation under this warranty shall be limited to
repair or replacement (at our option), during the warranty period of any part which proves
defective in material or workmanship under normal installation, use and service, provided
the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PRE-
PAID. Products returned to us or to an authorized Service Center must be accompanied
by a copy of the purchase receipt. In the absence of such purchase receipt, the warranty
period shall be one (1) year from the date of manufacture.
This warranty shall be invalid if the product is damaged as a result of deface-
ment, misuse, abuse, neglect, accident, destruction or alteration of the serial number,
improper electrical voltages or currents, repair, alteration or maintenance by any person
or party other than our own service facility or an authorized Service Center, or any use
violative of instructions furnished by us.
This one-year warranty is in lieu of all expressed warranties, obligations or li-
abilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, IN-
CLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED WAR-
RANTY. Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.
IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WAR-
RANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the
exclusion or limitation of special, incidental or consequential damages so the above limi-
tation or exclusion may not apply to you. This warranty gives you specifi c legal rights,
and you may also have other rights which vary from state to state.
ROLLS CORPORATION
SALT LAKE CITY, UTAH
5/06

INTRODUCTION
Thank you for your purchase of the ROLLS RPM26 Rack Power Module. The
RPM26 is a single rack space power distibution unit with eight rear-panel AC
outlets, and an individually switched outlet on the front panel. The RPM26 fea-
tures front-panel lighting in the form of brilliant white LED light. A Dimmer control
adjusts the brightness of the LEDS. Because of the low voltage and high efficien-
cy of these LEDs, they will likely never need replacing. An added feature is the
inclusion of a front panel 12VDC BNC connector to power external or gooseneck
type lights
.
Please read the following manual carefully to achieve the best results from this
product.
DESCRIPTION
FRONT PANEL
Switched Outlet: AC outlet.
Switch - Turns the Switched Outlet on and off.
Dimmer: Adjusts the brightness of the white LED lights.
12VDC: BNC connector for optional 12 volt lighting.
Power: Main power switch - Turns ALL outlets on and off.
REAR PANEL
100 - 220 VAC 50/60 HZ 10 VA: IEC Power Cord. Connect to a properly ground-
ed AC source. NOTE: REPLACE THE FUSE WITH ONLY THE PROPER RATED
FUSE. INSTALLING A FUSE OTHER THAN THE RECOMMENDED RATING
WILL DAMAGE THE UNIT.
POWER OUTLETS:
8 ea;
AC outlets. Rated for 8 amps maximum each.
INSTALLATION
Mount the RPM26 in a safe and sturdy rack. Connect the IEC power cable to the
RPM26, and to a properly grounded AC outlet.
Connect the power cables from your devices to the power outlets on the rear of
the RPM26.
Audio Device Warning
It is recommended that power amplifiers be switched OFF separate from the
RPM26 - to avoid power surges and possible damage to speakers (and your
ears). Switch power amplifiers
off
first
before
switching off the RPM26, and
switch the power amplifier on
after
the RPM26.
SPECIFICATIONS
AC Outlets: 9 ea; 8 rear panel, 1 front panel
Switches: 2 rocker type
Control: 1 variable Dimmer control
12VDC Out: BNC female connector / 250mA Max.
Voltage Regulation: None
Power: 100 - 230 VAC 50/60 Hz, 10A Max.
Size (W x H x D): 19” x 1.75” x 5” (48 x 4.5 x 12.7)
Weight: 5.5 lbs (2.5 kg)