Rollz Umbrella User manual

Umbrella for all Rollz rollators
Assembly and handling manual
Nederlandse handleiding
Deutsche Bedienungsanleitung
Manuel en français

2
Please read this assembly and handling manual before
installing the product.
Introduction
Thank you and congratulations with the purchase of the Rollz
umbrella.
Before installing the rollator umbrella, read the assembly and
handling manual and note all the safety instructions. When
the assembling of the umbrella has been completed you can
start enjoying the best quality and easy handling of this
product.
The umbrella gives optimal protection
against rain and sun, as they block the
harmful UV radiation almost completely.
The Air-Vent-System ensures stability in
windy weather.
Because of the space-saving placement
on the right side (usually) you can use
your rollator with both hands without
being restricted.
Please note that the Rollz umbrella fits
all Rollz rollators. Choose the chapter
that corresponds to your Rollz model for
detailed instructions.

3
Content of the package
In the package you will find:
• a rollator umbrella with two adjustable joints and a cover
(figure 1);
• the pre-assembled mounting clamp for the Rollz Motion
(Performance, Rhythm, Electric) (figure 2);
• the parts to rebuild the mounting clamp for the Rollz Flex
(figure 6);
• an Allen key for easy installation of the Rollz umbrella.
Plastic bags can be dangerous!
To avoid suffocation, keep the plastic bag
of the packaging away from infants and little
children.
Unlock button
Unlock button
Figure 1: Umbrella with two adjustable joints and unlock
buttons, including cover.
WARNING

4
Assembly on the Rollz Motion (Performance,
Rhythm, Electric)
Note: If you own a Rollz Flex, please skip to the next chapter.
The mounting clamp is pre-assembled for mounting on the
Rollz Motion. You can assemble the umbrella on both the left
and right side, but always make sure the mounting clamp
points backwards (figure 4).
The clamp consists of two parts (figure 2). First attach the
rollator part on the frame of your Rollz Motion. Then fasten the
umbrella to the umbrella part. Find out how to assemble it on
the next pages.
Figure 2: Pre-assembled mounting clamp for the Rollz Motion
umbrella and an Allen key.
spacer ring X
umbrella part
rollator part

5
Figure 3: All the necessary parts for fitting the umbrella on the
Rollz Motion.
spacer ring X
Figure 4: The mounting clamp should be placed on the frame of
your Rollz Motion as high as possible.

6
Assembling goes as follows:
• Make sure to not lose the small pre-mounted spacer ring X
placed in-between the clamps of the mounting clamp. It
should always remain on the long Allen screw with flat head
(figure 3).
• Untighten the screws from the rollator part (figure 2) and
fix the mounting clamp as high as possible on the frame,
with help of the Allen key (figure 4). Make sure the umbrella
part is pointing backwards and the plastic wing nut is
pointing outwards (figure 4).
• Tighten the screws firmly.
• You can now place the umbrella pole in the umbrella clamp
from above and tighten the plastic wing nut (figure 4).
• The adjusting ring Y (figure 5) can be placed on the umbrella
pole the for setting the umbrella to the desired height. Make
sure you place the adjusting ring Y above the umbrella part
(figure 2) to keep the umbrella from moving down. You can
choose from a maximum of five different heights.
• The distance between the tip of the umbrella and the ground
should be at least 3-5 cm when the umbrella is folded.
• Tighten the screws again after two days.
Figure 5: Attaching the
adjusting ring Y.

7
Assembly on the Rollz Flex
Note: If you own a Rollz Motion, please return to the previous chapter.
The mounting clamp is default pre-assembled for the Rollz
Motion. Therefore the parts have to be swapped for the Rollz
Flex. The changing of the clamp goes as follows (figure 6):
• Unscrew the screws of the rollator part until both come
loose (figure 2). Remove both screws and the two black parts
labelled with indication number 25.
• Take the other two screws and two black parts from the Rollz
Flex mounting clamp (indication number 22) and screw them
in place with the gaps facing each other (figure 7).
Rollz Motion
mounting clamp
Indication number: 25
Rollz Flex
mounting clamp
Indication number: 22
Umbrella
mounting clamp
Indication number: 20
Figure 6: Preview of rebuilding mounting clamp from Rollz
Motion to Rollz Flex fitting.

8
umbrella part
Figure 7: Assembled mounting clamp for the Rollz Flex umbrella
and an Allen key.
rollator part
The mounting clamp is now assembled for mounting on the
Rollz Flex. You can assemble the umbrella on both the left and
right side, but always make sure the mounting clamp points
forwards (figure 9).
The clamp consists of two parts. First attach the rollator part
on the frame of your Rollz Flex. Then fasten the umbrella to the
umbrella part. Find out how to assemble it on the next pages.

9
Figure 8: All the necessary parts for fitting the umbrella on the
Rollz Flex rollator.
spacer ring X
Figure 9: The mounting clamp should be placed on the frame of
your Rollz Flex as high as possible.

10
Assembling goes as follows:
• Make sure to not lose the small pre-mounted spacer ring X
placed in-between the clamps of the mounting clamp. It
should always remain on the long Allen screw with flat head
(figure 8).
• Untighten the screws from the rollator part (figure 7) and
fix the mounting clamp as high as possible on the frame,
with help of the Allen key (figure 9). Make sure the
umbrella part is pointing forwards and the plastic wing nut
is pointing outwards (figure 9).
• Tighten the screws firmly.
• You can now place the umbrella pole in the umbrella clamp
from above and tighten the plastic wing nut (figure 9).
• The adjusting ring Y (figure 10) can be placed on the
umbrella pole the for setting the umbrella to the desired
height. Make sure you place the adjusting ring Y above
the umbrella part (figure 7) to keep the umbrella from
moving down. You can choose from a maximum of five
different heights.
• The distance between the tip of the umbrella and the ground
should be at least 3-5 cm when the umbrella is folded.
• Tighten the screws again after two days.
Figure 10: Attaching the
adjusting ring Y.