Rondish UT-11 User manual

Rondish
Company Limited
Reset Button
Cable Exit
Universal Transmitter
Door/Window Sensor
FCCID: WNG-UT-11
Manufacture by Rondish Company Limited
Unit G&H, 4/F, Block 1, Kwai Tak In . Ctr.,
15-33 Kwai Tak Street, Kwai Chung, N.T.
Hong Kong
www.ron ish.com
Setup
Step 1: Open UT-11 housin
-The bottom cover can be opene for the access
the power switch, external evice connector, an
settings ip switch.
Step 2: Select settin s (defaults in bold)
-Area code: allows alarms to be filtere on a
central monitor; ranges between 0-7 epen ing
on switch positions of 1-3:
0 – Off, Off, Off 4 – On, Off, Off
1 – Off, Off, On 5 – On, Off, On
2 – Off, On, Off 6 – On, On, Off
3 – Off, On, On 7 – On, On, On
-Latch: when OFF the UT-11 will transmit reset as
soon as it closes. When ON it transmits a reset
only when the Reset Button is presse , or
magnetic fob (Reset Key) is applie to the UMS.
-NC/NO: controls whether the UT-11 accepts a
connecte a Normally Close or Normally Open
evice. Door setting shoul be OFF if use .
-Trackin : when enable the UT-11 sen s a
heartbeat every 20 mins. (out of range etection)
-Door: when enable the UT-11 will monitor
whether the provi e magnetic sensor switch is
open or close . Turn this OFF if you will connect
an external evice.
-Reset: when ON the Reset button is enable .
When OFF you must touch a magnetic fob to the
UMS to sen a reset signal
Step 3: Connect external device (if needed)
-Remove the cable exit plastic cover for the cable
connection.
Step 4: Turn transmitter on
-Move the On/Off switch to the ON position (left).
The re LED on top housing will be on for ~2s
External evice
terminal connector
Re /Green
LED
On/Off switch
Settings
ip switch
UMS
Door
Magnetic
Switch
User
Magnetic
Switch
(U.M.S)

Step 5: Close Housin
-When the bottom cover is opene , the universal
transmitter is in stan by mo e. The bottom cover
must be close to start its operation
Step 6: Pair with Alarm
-First put the external alarm into its pairing mo e,
then close an open the magnetic switch to enter
the UT-11 into memory. Observe the alarm to
confirm the pairing process was successful.
Step 7: Mountin
-Use the ouble-si e tape or screws to fix the UT-
11 on the oor frame an the magnetic switch on
the oor. The gap shoul be < 7mm when the
oor/win ow is close . The Door setting must be
enable to allow the oor/win ow etection.
Operation
Alarm tri er
-When Door = ON, the UT-11 will alarm when the
oor or win ow opens
-When Door = OFF an NC/NO selection is set to
NC, the UT-11 will alarm when the circuit opens
-When Door = OFF an NC/NO selection is set to
NO, the UT-11 will alarm when the circuit closes
-The UT-11 will alarm if the housing is opene
Alarm reset
-When Latch = OFF, the alarm will reset when the
oor/win ow closes
-When Latche = ON, the alarm will reset by
pressing the Reset button or using a fob on HES
-When Reset = OFF, the alarm will reset only by
touching a fob to the HES
Bypass function
If Reset is presse with no alarm on, it allows 15
secon s to exit the oor without sen ing an alarm
signal.
Behavior Chart
Call Triggere Re LED stays for 5s
Call Reset Green LED flashes 3x
Alarm Bypass Green LED flashes for 15s
Tamper alert Re LED stays for 5s
Low Battery Re LED blinks once every 5s
Specifications
Battery 1 x CR2477 lithium
Frequency 433.92MHz
Range 70m
Tracking 30min
Size 80 x 41 x 19mm
Weight 50g
Compatibility
Room
In icators
ILB-21 Over-Door Light
Call Systems ZP-01(S) Network Repeater
Pagers PAG-11 Caregiver Alert Pager
PAG-31 Economy Pager
Be Monitors NGM-21 Cor Free Monitor
NGM-41 Economy Cor less
Accessories CR2477 Lithium coin battery
CK-01 Caregiver Key magnet
WARNING: Risk of explosion if battery is replace
by an incorrect type. Replace only with the same or
equivalent type.
CAUTION: Lithium batteries cannot be ispose of
with normal househol waste. For isposal or
recycling instructions please contact your local
authorities.
Warnings.
Test regularly to ensure alarms are working
properly.
This pro uct uses ra io frequency signals, which
can be affecte by buil ing layout an
construction materials. The manufacturer
cannot guarantee the wireless range you get
will match the estimates provi e . You shoul
test that there are no “ ea areas” in your
facility where alarms cannot be receive .
FCC & CE Compliance
This evice complies with part 15 of the FCC Rules.
Operation is subject to the following two con itions:
(1) This evice may not cause harmful interference,
an (2) this evice must accept any interference
receive , inclu ing interference that may cause
un esire operation.

Notes:
Any changes or mo ifications not expressly
approve by the party responsible for compliance
coul voi your authority to operate the equipment.
This equipment has been teste an foun to
comply with the limits for a Class B igital evice,
pursuant to part 15 of the FCC Rules. These limits
are esigne to provi e reasonable protection
against harmful interference in a resi ential
installation. This equipment generates, uses, an can
ra iate ra io frequency energy an , if not installe
an use in accor ance with the instructions, may
cause harmful interference to ra io communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment oes cause harmful interference to ra io
or television reception, which can be etermine by
turning the equipment off an on, the user is
encourage to try to correct the interference by one
or more of the following measures:
•Reorient or relocate the receiving
antenna.
•Increase the separation between the
equipment an receiver.
•Connect the equipment into an outlet
on a circuit ifferent from that to which
the receiver is connecte .
•Consult the ealer or an experience RF
technician for help.
This pro uct contains a coin / button cell battery. If
the coin / button cell battery is swallowe , it can
cause severe internal burns in just 2 hours an can
lea to eath.
Keep new an use batteries away from chil ren.
If the battery compartment oes not close securely,
stop using the pro uct an keep it away from
chil ren.
If you think batteries might have been swallowe or
place insi e any part of the bo y, seek imme iate
me ical attention.
RF exposure statements
This equipment complies with FCC ra iation
exposure requirement set forth for an uncontrolle
environment. En users must follow the specific
operating instructions for satisfying RF exposure
compliance.
EU eclaration of conformity
Ron ish Co. Lt hereby eclares that the evice is in compliance with the
essential requirements an other relevant provisions of irectives
2014/53/EU, 2014/35/EU & 2014/30/EU .
Operate Frequency Ban s : 433.92MHz
Max. output power: 10mW