Room & Board ASHBY User manual

CRIB ASSEMBLY INSTRUCTIONS
For ASHBY Crib
DO NOT USE POWER TOOLS!
Step 1: Lay the Base Frame on top of the Feet, and secure using 4
Decorative Nickel Bolts and Lock Washers. (Base Frame should be
oriented so that the countersunk holes face the floor.)
Step 2: Place one of the End Panels on the left side of the Base Panel
so that the silver metal inserts are facing inward. Use 2 Decorative
Nickel Bolts and Lock Washers to secure the End Panel to the Base
from underneath the Base Frame, but DO NOT tighten the Bolts
completely yet. Repeat this procedure on the right.
Step 3: Attach one of the Sides to the End Panels with 4 Decorative
Nickel Bolts and Lock Washers using the enclosed Z Wrench. Place
the Bolts through the end slat of the Side and into the End Panel, but DO
NOT tighten completely.
Step 1: Attach Feet to Base
Step 2: Attach End Panels to Base
Step 3: Attach Side to End Panels
Step 4: Screw a Bronze Bolt and Lock Washer in each of the top
holes of the center columns of inserts on the End Panels. Leave the bolts
sticking out about an inch. This configuration puts the Mattress in the highest
position, which is the height recommended for newborns. To select a lower
position, place the bolts in lower holes. Place the Mattress Support
Platform over the Bolts. The notches in the Platform fit snugly over the
Bolts.
Step 5: Attach the other Side to the End Panels as in step 2. Now tighten
all 16 Bolts on crib completely.

Conversion to Toddler Bed: The crib mattress should be in lowest
position (Bolts in the lowest holes.) Remove the front Side by undoing
what you did in Step 4. Remember to loosen ALL Decorative Bolts
before attempting to remove the Side. Use the bolts and lock washers
you removed to attach the Toddler Rail as in Step 4.
For Toddler Bed use, the minimum age shall be no less than 15
months and the maximum weight shall not be greater than 50 lbs
(22.7kg). The mattress used on the toddler bed shall be a full-size crib
mattress at least 27 ¼ (131cm) by 51 5/8 in (69cm) with a thickness of
no less than 4 in. (11cm) and not exceeding 6 in. (15cm).
Maintenance: Periodically check to make sure all screws, bolts and
fastening devices are tight. Before each usage or assembly, inspect crib
for damaged hardware, loose joints, missing parts or sharp edges. DO
NOT use crib if parts are missing or broken. DO NOT substitute
parts. DO NOT make any alteration to this crib.
Cleaning: Mix a mild solution of gentle dishwashing liquid and water,
apply to crib surface using a soft, clean cloth, then dry all surfaces with
a soft, dry cloth. NO ABRASIVES, SCOURING PADS, STEEL WOOL,
OR COARSE RAGS should be used to clean this fine furniture.
Storage: A Plastic Pouch is attached to the crib spring for storage
of the assembly instructions for future referral. After completing the
assembly, you are advised to read and be aware of all WARNINGS,
CAUTIONS, CLEANING, STORAGE AND MAINTENANCE notices
contained herein. We caution you not to place excess hardware in the
plastic pouch as it could present danger to a child if retrieved and it
could also puncture the crib mattress. When storing crib, use
CAUTION as extreme temperature or humidity changes could be
harmful.
PARTS INCLUDED IN CARTON
1 –BASE FRAME AND 2 FEET 2 –END PANELS 2 –SIDES 1 –MATTRESS SUPPORT PLATFORM
PARTS INCLUDED IN HARDWARE BAG
16 –DECORATIVE NICKEL BOLTS (50mm) 1 –BALL END ALLEN WRENCH 1 –Z-WRENCH 20 –LOCK WASHERS
4 –DECORATIVE BRONZE BOLTS (35mm)

CRIB ASSEMBLY INSTRUCTIONS
For Ashby Crib
•Read all instructions before assembling crib.
•Keep instructions for future use.
WARNING: INFANTS CAN SUFFOCATE
ON SOFT BEDDING. NEVER ADD A PILLOW OR
COMFORTER. NEVER PLACE ADDITIONAL
PADDING UNDER AN INFANT.
•To reduce the risk of SIDS, pediatricians recommend healthy
infants be placed on their backs to sleep, unless otherwise
advised by your physician.
Strangulation Hazard:
•Strings can cause strangulation! DO NOT place items with a
string around a child’s neck, such as hood strings or pacifier
cords. DO NOT suspend strings over a crib or toddler bed
or attach strings to toys.
•To help prevent strangulation tighten all fasteners. A child can
trap parts of the body or clothing on loose fasteners.
•DO NOT place crib or toddler bed near window where cords
from blinds or drapes may strangle a child.
Fall Hazard:
•When child is able to pull to a standing position, set mattress
to lowest position and remove bumper pads, large toys and
other objects that could serve as steps for climbing out.
•Stop using crib when child begins to climb out or reaches the
height of 35 in. (89cm).
CAUTION: ANY MATTRESS USED IN THIS CRIB
SHALL BE AT LEAST 27 ¼ INCHES (69 CM) BY 51 5/8 INCHES
(131 CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15
CM).
•Check this product for damaged hardware, loose joints, loose
bolts or other fasteners, missing parts, or sharp edges before and
after assembly and frequently during use. Securely tighten loose
bolts and other fasteners. DO NOT use crib if any parts are
missing, damaged or broken. Contact your ROOM & BOARD®
STORE or EL GRECO WOODWORKING for replacement
parts and instructional literature if needed. DO NOT substitute
parts.
•If refinishing, use a non-toxic finish specified for children’s
products.
•Follow warnings on all products in a crib.
•Never use plastic shipping bags or other plastic film as a mattress
covers because they can cause suffocation.
•Infants can suffocate in gaps between crib sides and a mattress that
is too small.
•PERIODICALLY CHECK TO SEE THAT ALL BOLTS ARE
SECURELY TIGHTENED.
WARNING: FAILURE TO FOLLOW
THESE WARNINGS AND ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.