Room & Board Nest Crib User manual

CRIB ASSEMBLY INSTRUCTIONS
for Nest Crib
PARTS INCLUDED IN CARTON
2 –HEADBOADS 2 –SIDES 1 –MATTRESS SUPPORT PLATFORM
PARTS INCLUDED IN HARDWARE BAG
8 –DECORATIVE BOLTS (50mm) 8 –LOCK WASHERS 4 –SERRATED BOLTS (20mm)
1 –BALL END ALLEN WRENCH

CRIB ASSEMBLY INSTRUCTIONS
For Nest Crib
•Read all instructions before assembling crib.
•Keep instructions for future use.
WARNING: INFANTS CAN SUFFOCATE
ON SOFT BEDDING. NEVER ADD A PILLOW OR
COMFORTER. NEVER PLACE ADDITIONAL
PADDING UNDER AN INFANT.
•To reduce the risk of SIDS, pediatricians recommend healthy
infants be placed on their backs to sleep, unless otherwise
advised by your physician.
Strangulation Hazard:
•Strings can cause strangulation! DO NOT place items with a
string around a child’s neck, such as hood strings or pacifier
cords. DO NOT suspend strings over a crib or toddler bed
or attach strings to toys.
•To help prevent strangulation tighten all fasteners. A child can
trap parts of the body or clothing on loose fasteners.
•DO NOT place crib or toddler bed near window where cords
from blinds or drapes may strangle a child.
Fall Hazard:
•When child is able to pull to a standing position, set mattress
to lowest position and remove bumper pads, large toys and
other objects that could serve as steps for climbing out.
•Stop using crib when child begins to climb out or reaches the
height of 35 in. (89cm).
CAUTION: ANY MATTRESS USED IN THIS CRIB
SHALL BE AT LEAST 27 ¼ INCHES (69 CM) BY 51 5/8 INCHES
(131 CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15
CM).
•Check this product for damaged hardware, loose joints, loose
bolts or other fasteners, missing parts, or sharp edges before and
after assembly and frequently during use. Securely tighten loose
bolts and other fasteners. DO NOT use crib if any parts are
missing, damaged or broken. Contact your ROOM & BOARD®
STORE or EL GRECO WOODWORKING for replacement
parts and instructional literature if needed. DO NOT substitute
parts.
•If refinishing, use a non-toxic finish specified for children’s
products.
•Follow warnings on all products in a crib.
•Never use plastic shipping bags or other plastic film as a mattress
covers because they can cause suffocation.
•Infants can suffocate in gaps between crib sides and a mattress that
is too small.
•PERIODICALLY CHECK TO SEE THAT ALL BOLTS ARE
SECURELY TIGHTENED.
WARNING: FAILURE TO FOLLOW
THESE WARNINGS AND ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.

CRIB ASSEMBLY INSTRUCTIONS
for Nest Crib
DO NOT USE POWER TOOLS!
STEP 1: Mount one Side to the rear posts of the Headboards.Use four Decorative Bolts and Lock Washers to fasten the side to the
posts. DO NOT tighten the bolts completely yet.
STEP 2: Install the Mattress Support Platform in the crib with the flat side up. Extend the mounting flange on each corner and attach the
spring to headboard and footboard at the desired level using four Serrated Bolts. The top position is recommended for
newborns. The bottom position must be used when the baby is able to kneel or stand in the crib.
STEP 3: Mount the other Side to the posts of the Headboards. Use four Decorative Bolts and Lock Washers to fasten the side to
the posts. Tighten all bolts, including the ones from the first side, with the Allen wrench provided.
STEP 4: Once the crib is in use, periodically check to make sure all bolts are tight, and tighten as necessary. For future use, keep these
instructions in the plastic bag attached to the mattress support spring.
Conversion to Toddler Bed: Mattress should be in lowest position. Remove one Side by unscrewing the 4 Decorative Bolts holding it in
place. Be sure to loosen all the other Decorative Bolts before attempting to remove the Side. Once removed, attach Toddler Rail (sold
separately) using three of the Decorative Bolts and Lock Washers you just removed, and retighten all remaining Decorative Bolts.
This crib may not be used as a toddler bed without a toddler rail.
For Toddler Bed use, the minimum age shall be no less than 15 months and the maximum weight shall not be greater than 50 lb (22.7kg). The
mattress used on the toddler bed shall be a full-size crib mattress at least 27 ¼ (131cm) by 51 5/8 in (69cm) with a thickness of no less than 4 in.
(11cm) and not exceeding 6 in. (15cm).
Maintenance: Upon completion of assembly be sure all screws, bolts and fastening devices have been tightened securely. Periodically repeat this
check to make sure all screws, bolts and fastening devices are tight. Before each usage or assembly, inspect crib for damaged hardware, loose
joints, missing parts or sharp edges. DO NOT use crib if parts are missing or broken. DO NOT substitute parts. DO NOT make any alteration to
this crib.
Cleaning: Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using a soft clean cloth lightly dampened in the
solution. Rinse with clean water again using a soft clean cloth, then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS,
SCOURING PADS, STEEL WOOL OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
Storage: A plastic pouch is attached to the crib for the storage of the assembly directions for future referral. After completing the assembly
process you are advised to read and beware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices
contained in these instructions. We caution you not to place excess hardware in the plastic pouch as it could present danger to a child if retrieved
and it could also puncture the crib mattress.

NEST CRIB ASSEMBLY INSTRUCTIONS