Roper Roper FEP210VL0 User manual

Before you start...
Proper installation is the insmlleis
responsibility. A qualified teclmiclsn
should install this range. Make sure you
have everythhg necesssIy for correct
installation. It is the responsibility of tbe
lr!stier to comply with the installation
clearances specified on the serlalfrating
plate. The sewrating plate is located
under the cooktop.
Check location where range will be
installed The range should be located for
convenient use in kitchen
ALL OPENINGSIN THE WALL OR
FLOORWHERERANGE ISTO BEIN-
STALLEDMUST
BESEALED.
\ \ \
Important: Observe all ‘\,
governing codes and
ordinances.
Mobile home installation
The installation of tbis range must
conform to the Manufactured Home
Corshuction end Safety Standards, Title
24CFR,Part 3280(formerly the Federal
Standard for Mobile Home Conshuction
and Safely. Title 24.HUD, Part 280); or
when such standard is not appltcable.
the Standard for Manufactured Home
Installation 1982(Manufactured Home
Sites. Communities and Setups),ANSI
A225, l-1987, orlatest edItIon. or with
local codes.
When this range Is installed in a mobile
home, it must be secued to the floor
during trsnslt. Any method of securing
the range is adequate aslong as it
conform to the standards listed above.
Four-wire power supply cord must be
used in a mobile home installation The
appliance wiring will need to be revised
SeeElectrical requirements.
Copies of the standards
listed may be obtained from:
l National Fire Protection Association
Batterymarch Park
Cluincy, Massachusetts 02269
Avold cabinet f&g; above the
cooking surface. If wbfnets 6re
shady histalled, reduce the hazard
of reaching over a heated cooking
surface by InsmIlIng e range hood
The range hood should extend a
minlmnm o! 5inches out from the
bottom of the cabfneta.
Tools needed
for installation:
Panel A
Electrical ’
requirements
Save Installation Instructions for
electrical inspector’s use.
A power supply cord is not supplled
with thin producl. but is available
Eouih your local elecuical supply
Electrical Shock Hazard
1Electrical ground is rewed on
this appliance.
1Improper connection of the
equipment-gounding conductor
can result in elecuicsl shock.
1Check with a qualified elect&Ian
if you are in doubt as to whether
the appliance is properly
arounded.
I only a power supply cord kit rated
at 250volts. 40 ammeresend
investigated for use with ranges
should be used.
1Do Not use an extension cord with
this appliance. Suchuse may result
in a fire. electrical shock or other
personal injury.
.~
mDo Not have a fuse in the neutral 01
woundJng cimdt. A fuse in the
neutral or grounding circuit could
result in electrical shock.
1Do Not plug the “pigtail” power
cord into a live well receptacle
Wore the cord la permanently
connected to the terminal block To
do somay result in pereonal injury
horn elecvical shock.
Failure to follow these fustructions
could result ia an electrical rho& or
personal injury.
Reachiug over a heated cooking
surface could result in a serious burn
or other pe~~cml injuy.
Electrical Shock Hazard
It is the customer’s responsibility:
~TOcontact a quaIified eleceical
Installer.
#Toassure that electrical
installation is adequate end in
conformance with National
Elect&al Code, ANSWWPA ‘70.
lateat edition’. and all local codee
and ordinances.
Failure to do so could result In fire.
elechicd ahock or other personal
injury.
A
A threewIre or four-wire, single
n phase, 120/240-volt. GO-Hz,AC
only electrical supply (or tbreewire
or four-wire 120/2O&volt if specified
onseti plate)isrequkedona
separate,IO-amperecircuit, fused
on both sides of the line. A time-delay or
circuit breaker Isrecommended
B
THE RANGE MUST BECONNECTED
n WfTH COPPERWIREONLY.
C
Local codesmay permit the
s use of aU.L.-lIsted 250-volt, 40.
ampere range power supply cord (pigtail).
This cord contains three, No.-10copper
wires and matches a three-wire receptacle
of NEMA Type lo-50R, shown in Figure 1.
Connectors on the appUanceend must be
rinQ terminals. A U.L.-listed strain relief
must be provided at tbe point the power
supply cord enters the appliance.
D
The appliance may be connected
n drectlv to the fused disconnect or
circuit brake; box through flexible,
armored or non-metallic sheathed, copper
cable. Allow two or three feet of slack in
theUnesothatitcanbemovedlf
servicing is ever necessary. A IJ.L.-listed
conduit connector must be provided at
each end of the power supply cable (at
the appliauce and at the junction box).
Wire sizes (COPPERWIREONLY) end
conuecUon6mwt conform with the rating
of the appliance (40emperes).

E
IF CONNECTING TO A 4-WIFtE
. ELECTRICAL SYSTEM:This
appliance is msnufactured with ground
connected to cabinet. The ground must
be revised so the green grounding wire
of the I-wire power cord is connected to
the osbklet. See4-w&e elect&al
connection section, Panel c.
When a I-wire receptaole of NEMA type
14-60Ris used (SeeFigure 2) a matching
U.L.-listed, I-wire, 250~volt,IO-ampere.
range power supply cord (pigtall) must be
used. This cord conteins four copper
conductors with ring terminals on the
appliance end, terminating in a NEMA
Type 14.50Pplug on the supply end. The
fourth (grounding) conductor roust be
identified by a green or green/yellow
cover and the neu&al conductor by a
white cover. Cord should be Type SPDor
SFlDTwith aU.L.-listed snain relief and
he aleast four feet long.
The IvXWMUM conductor sizes for
the copper I-wire power cord are:
IO-ampere cfrcult
2.No.-8 conductors
1,No.-10white neutral
1,No.-8 green grounding
F
The wiring diagram L also
. located on the back of the range.
Now start...
With range in kitchen.
1 Removeracks
and other parts from
. inside oven
2
.
Placeone foot on the shi~~ina base. Tilt
range forward slightly tdfee-rear legs.
Gently lower range to floor. Tilt range
backwards until front legs ere free.
3
Remove shipping materiels,
. tape and protective film from range.
Donot remove cardboard shipping base
at tbis the.
4
Adjust the levehng legs
. approximately l/4’ or to a point
where the range base does not touch the
iloor. (If model is so equipped.)
Persona3lniurv Hazard
Carefully remove he-rear access
nanel when attaching the newer
eupply cord. The rear-acceia panel
contains a counterweight bon
making it heavier than it appears.
Faflure to follow this hast.rnction
may result in personal injury.
J
3-wire electrical connection
SeePanel Cfor I-wire electrical
connection
Take the strsjn relief from the power
supplycordkitandfnsertitintothehole
MOWtbteIUlblblock.hlSertthe
power cord through the snalu relief
allowinuenouahslacktoeasfivattachto
tetminr;ihlook-
Useonly r&~-type tetmbds to oouneu
power supply cord Use3/V Imassnuul
(provided with the range) to seam the
~~w.‘erm&y cord. DoNot loostm
factory-bstelled nuta already hmtalled
on the t6mnhaL Besue factory
instelled nuta are tight.
sil”,
tern
nu*
ef md IO-am~ore
This appllauca Ismauufachxed with
neutIal tmlninal wnuected to the frame.
If local ocdw and ordinancw Do Not
pmmit grounding through the neutral. a
four-wire powar supply oord.rated 250
volts, 40amperes and investigated for use
with ranges must he used.SeeI-wire
elechicel wnnection, Panel C.
7
Connectthe neunal (white)
. wire to the center silver-colored
terminal mew onthe terminal block
Connectthe other two wires to the outer
Wminalscrewsontheterminalhlo&
Att8ch washers endhex nuts supplied in
the parts packege.Checkthat nuts are
tight t0 irwJe proper eleceical COM~OUOKL
8
Tighten the stmin relief screws or
mconduit connector clamping
screws. Replazeeccesspanel
aTo prevent tipping, install range
anti-Up bracket.
n Save thew hatallation
Instrwtlons. If range in moved to a
new locatlos the anti-tip bracket
must he removed and reinstalled
In thenew location.
9 ill0 anti-tip bracket must be
. installed. Anti-tip bracket may
befestenedtothefloorundertherangeor
wall ldind tile range.
-
To Install antl-tip bracket on wall:
mMeasure and mark a line at the center
of the cabinet opening o* the rear wall.
Measure end mark lines 7-13116’and
S-16/16’from either the left (shown) or
right side of the centerbne on the rear
wall Measure and mark on the rear wall
aline 3/E’ from the floor.
To InstaIl anti-tip bracket on flooc
l Measure and mark a line at the center
of the cabinet opening on the Soor.
Measure and mark lines 7-13/W and
&36/16’from either the left (shown) or
right side of the centerline on the floor.
Measure and mark on the floor aline 1’
from the rear wall
Note: If there is a cabinet on only one
side, install the autl-Up bracket next to
the cabinet. using the measurements
given
Propeay Damage
1Contact a qualified insteller for the
best procedure to drill mounting
holes through your type of floor
covering.
1Before moving range across floor,
check that range is on shipping
base or slide renae onto cardboard
orhardboard. -
Failure to follow these instructions
may result in damage to floor
covering.
bracket to wood
floor or wall, driJl l/3’
holes at the two motmtmg
screw locations where the two bnes
ere crossed by the third line. ,,
To mount sntl-tip
bracket to concrete or
ceradc floor or wall,
use a masonry drill bit to
ddl l/4’ holes at each
mounting screw
location Tap plastic
anchors km mounting
holes in floor or wall with
a hammer,
11.
Line up holes in
anti-tip bracket
with holes In floor
or wall Use the
screws provided to
mount the anti-tip
bracket to the floor
or wall
12
Move range close to fineI
n position. Remove shipping base,
cardboard or herdboard horn under the
range. Plug power supply cord into
grounded outlet.
I II I Ill
13.
Carefully move range
final position Pull bottom of front panel
out and lift up to remove penel. Look
under range (a Saahlight may be needed)
to check that anti-tip bracket overlaps
range base. If anti-tfp bracket does not
overlap base, remove range and
reposition bracket to insure that range
base will fit properly under bracket.
the range to the floor.‘Any method of
securing the range is ad&ate aslong
asit conforms to the stauderds l&ted io
the Mobile home installation
instructions, Panel A.

Range must be secured when mobile
home is moved and at all times in a RV.
recreational vehicle using the method
descrlhed.
Pull bottom of front Dane1out end lift UD
to remove panel. Removing levehng -
legs.
16
Securebe range using 6/16”bolts,
washers andnuts through the leveling
leg holes. Replacelower accesspanel.
Skipstep 17.
Placerack in oven. Place
n level on rack, first side to side;
then front to back If range is not level at
the tiont, adjust the leveling legs up or
down until the range is level. If reer of
range needs adjusting, adjust rear
leveling legs up or down until range is
level. If rear legs sre adjusted downward
more than l/8”. add shims under anti-tip
bracket. Replacefront panel.
Note: Oven must be level for satisfactory
baking conchtlons.
4-wire electrical connection
Use this wirhg method for mobile homes
and whenever 4-wire installation Fs
required
Personal Injury Hazard
Carefully remove the rear access
panel when attaching the power
supply cord. The rear accesspanel
contains a counterweight box
making it heavier than it appears.
Failure to follow this h~truction
may result in penonal Lniury.
Take the strain relfef from the
power supply cord kit end insert it
into the hole below the terminal block.
Insert the power supply cable through
the strah relief ellowhg enough slack to
easily attach to the terminal block.
B
Remove the grounding link from
. the terminal block. Removethe
green grounding screw and place it with
your other parts.
To get the most efficient
use from your new Roper range,
read your Roper Use and Care
Guide. KeepInstallation
lnatrucrione and Guide close to the
range for easy reference.
5. 6.
7. 8.
--
C
Connect the green grounding
n wiretotherangeusfngthe
grounding screw removed in StepB.The
green growding wire must be attached
first and must not contact any other
.--
D connecttheneutral
(white)
. wire to the center, silver-colored
tmminal screw on the termhal block.
Connect the other two wires to the outer
terminals on the terraInal block. Use ring
type tembals only. Attach washers and
hex nuts aUDDlied in the PUtS Packaee.
Check that dirts ere tight-to tn.&e proper
electrical connection
E
Tighten the strain relief screws.
mReplace accesspanel.
F
Contluue hstallatIon at Step 9,
mPanelB.
Numbers
correspond
to steps.
13. 14. 15. 16. 17.
Panel C

If range does not
operate...
. Check that the circuit breaker is not
tripped or the fuse blown.
mCheck that power supply cord is
plugged into wall receptacle.
I
NOTE: I
Refer to Use and Care Guide for
operating instructiona and cleaning
iILmuctiolls.
Part No. 76409-W/4315463 Rev. A
&, 1991
For cleaning and
maintenance...
If removing the range is necessary for
deerhgandmaintenan0e,disconnect
elecmd SuPplY.
If ekctdcal supply is inaccessible, lift the
range slightly at the front and pull the
range away from the wall. Pun tb13range
outonlyasfsras neoessaIytodisoomlect
the eleohic supply line.
$zz.ge to complete cleaning
Move range back into operating position
Level the range. Reoonneot the eleotdoal
supply. Make sure that anti-tip bracket
Personal ti]urymmduct
Damage Hazard
Do Not step, lean or sit on the range
drawer or door.
Failure to follow these instruction9
could result in personal injuxy and/or
product damage.
Benton Harbor, IvWhigau 49022
If you need
assistance...
Call your dealer or local authorized
sexvloe campany. when you oau you will
need the range model number and serial
number. Both numbers can be found on
the sw-ialhting plate located under the
cooktoP.
PrhltedinU.S.A.