Rose electronics ORION lc User manual

ORI
ORIORI
ORION™ LC
ON™ LC ON™ LC
ON™ LC Multifunction DVI KVM Switch
10707 Stancliff Road
Houston, Texas 77099 800-333-9343
www.rose.com
INSTALLATION
AND
OPERATIONS MANUAL

LIMITED WARRANTY
Copyright Rose Electronics 2008. All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any
means, electronic or mechanical, including photocopying and recording, without the prior written permission
of Rose Electronics.
Rose Electronics Part # MAN-OR-DVI
Printed In the United States of America – Revision 1.7
Rose Electronics
®
warrants the ORION LC™ to be in good working order for one year from the date
of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good
working order at any time during this one-year warranty period, Rose Electronics will, at its option,
repair or replace the Unit as set forth below. Repair parts and replacement units will be either
reconditioned or new. All replaced parts become the property of Rose Electronics. This limited
warranty does not include service to repair damage to the Unit resulting from accident, disaster,
abuse, or unauthorized modification of the Unit, including static discharge and power surges.
Limited Warranty service may be obtained by delivering this unit during the one-year warranty period
to Rose Electronics or an authorized repair center providing a proof of purchase date. If this Unit is
delivered by mail, you agree to insure the Unit or assume the risk of loss or damage in transit, to
prepay shipping charges to the warranty service location, and to use the original shipping container or
its equivalent. You must call for a return authorization number first. Under no circumstances will a unit
be accepted without a return authorization number. Contact an authorized repair center or Rose
Electronics for further information.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE, AND NO
WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTIED ABOVE, YOUR SOLE
REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE. IN NO EVENT WILL
ROSE ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING ANY LOST
PROFITS, LOST SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OF OR THE INABILITY TO USE SUCH PRODUCT, EVEN IF ROSE
ELECTRONICS OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE MAY NOT APPLY
TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
IBM, AT, and PS/2 are trademarks of International Business Machines Corp. Microsoft and Microsoft
Windows are registered trademarks of Microsoft Corp. Any other trademarks mentioned in this
manual are acknowledged to be the property of the trademark owner.

EUROPEAN UNION DECLARATION OF CONFORMITY
ACCORDING TO COUNCIL DIRECTIVE 89/336EEC
This equipment is in conformity with the
protection requirements of the following
Council Directives:
The Declaration of Conformity is based upon
compliance of the product with the following
harmonized standards:
EN 55022: 1999 Class A
EN 55024: 1999
IEC 61000-4-2: 2001
IEC 61000-4-3: 2001
IEC61000-4-4: 2001
EN 61000-3-2 2001
EN 61000-3-3: 2002
This equipment has been found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

TABLE of CONTENTS
Contents Page #
Disclaimer ...................................................................................................... 1
System introduction ....................................................................................... 1
Features......................................................................................................... 2
Compatibility .................................................................................................. 2
DDC Information............................................................................................ 3
Next Frame Switching.................................................................................... 3
KVM Transmitter and Receiver information................................................... 3
Installation Selection...................................................................................... 4
Multiplex Repeater ..................................................................................... 4
Multiplex Repeater Installation 1 x 7 .......................................................... 4
Multiplex Repeater Installation 2 x 3 .......................................................... 5
Multiplex Repeater Installation 4 x 4 .......................................................... 6
Multiplex Repeater Operation .................................................................... 8
Crosspoint-Switch Installation.................................................................... 9
Crosspoint-Switch Installation – 1 x 7........................................................ 9
Crosspoint-Switch Installation – 2 x 6...................................................... 10
Crosspoint-Switch Installation – 3 x 5...................................................... 11
Crosspoint-Switch Installation – 4 x 4...................................................... 12
Crosspoint-Switch Installation – 5 x 3...................................................... 13
Crosspoint-Switch Installation – 6 x 2...................................................... 14
Crosspoint-Switch Installation – 7 x 1...................................................... 15
Crosspoint Switch Operation.................................................................... 16
KVM Switch.............................................................................................. 18
Single Head KVM Switch Installation ................................................... 18
Dual Head KVM Switch Installation...................................................... 19
Single Head KVM Switch Installation (Cascaded System) ..................20
KVM Switch Operation (All configurations).............................................. 21
Operation by Push Button .................................................................... 21
Operation by Keyboard commands......................................................21
Keyboard Commands............................................................................... 23
Serial switching operation ........................................................................ 24
Service Information...................................................................................... 25
Maintenance and Repair.......................................................................... 25
Technical Support .................................................................................... 25
Troubleshooting - Monitor............................................................................ 28
Troubleshooting - Keyboard ........................................................................ 28
Troubleshooting – USB- Keyboard/ Mouse................................................. 29

Figures Page #
Figure 1. 1x7 Multiplex Receiver................................................................... 4
Figure 2. Multiplex Repeater 2x3................................................................... 5
Figure 3. Multiplex Repeater 4x4................................................................... 6
Figure 4. Multiplex Repeater (Cascaded configuration)................................ 7
Figure 5. Crosspoint-Switch 1 x 7.................................................................. 9
Figure 6. Cross Point Switch - 2 x 6............................................................ 10
Figure 7. Cross Point Switch - 3 x 5............................................................ 11
Figure 8. Cross Point Switch - 4 x 4............................................................ 12
Figure 9. Cross Point Switch - 5 x 3............................................................ 13
Figure 10. Cross Point Switch - 6 x 2.......................................................... 14
Figure 11. Cross Point Switch - 7 x 1.......................................................... 15
Figure 12. Serial switching........................................................................... 16
Figure 13. Single Head KVM Switch ........................................................... 18
Figure 14. Dual Head KVM Switch.............................................................. 19
Figure 15. Single Head KVM Switch (Cascaded)........................................ 20
Appendices Page #
Appendix A – General specifications........................................................... 30
Appendix B – Part numbers......................................................................... 31
Appendix C – Serial / Audio set-up.............................................................. 31
Appendix D Serial command functions........................................................ 32
Appendix E – Serial command protocol ...................................................... 33
Appendix F – Rack mount ........................................................................... 33
Appendix G – DDC / Color Depth / Moment of Switching........................... 34

INTRODUCTION
ORION LC Installation and Operations Manual 1
Disclaimer
While every precaution has been taken in the preparation of this manual, the
manufacturer assumes no responsibility for errors or omissions. Neither
does the manufacturer assume any liability for damages resulting from the
use of the information contained herein. The manufacturer reserves the
right to change the specifications, functions, or circuitry of the product
without notice.
The manufacturer cannot accept liability for damages due to misuse of the
product or other circumstances outside the manufacturer’s control. The
manufacturer will not be responsible for any loss, damage, or injury arising
directly or indirectly from the use of this product.
System introduction
Thank you for choosing the Rose Electronics

ORIONLC switch. The
Orion LC is the result of Rose Electronics commitment to providing state-of-
the-art solutions for today’s demanding workplace. The Orion LC has
proven to be a valuable investment for any business, big or small, that has a
need to switch and extend single or multiple DVI signals to a single or
multiple displays. The ORION LC’s flexibility allows you to switch and
extend 1 DVI video input signal to 7 outputs, 2 inputs to 6 outputs, 3 to 5, 4
to 4, 5 to 3, 6 to 2, or 7 DVI inputs to 1 output over CATx or fiber cable.
The ORION LC’s versatility makes it the perfect addition for selecting,
switching, or distributing video to a single or multiple stations. The unit can
be cascaded other units, increasing the capability to 49 accessible
computers.
The ORION LC unit can be configured to perform one of three different
functions. It can be configured as a Multiplex Repeater, a Crosspoint Switch
or a KVM switch.
As a Multiplex Repeater, the DVI video signals plus optional serial and audio
(See appendix C for serial / audio features) are equalized and distributed to
the video outputs. A single DVI source can be distributed to 7 screens, two
DVI sources to 3 screens, and 4 DVI sources to 4 screens.
The Crosspoint Switch feature allows you to switch each port as an input or
output port. For example you can distribute 3 video sources to 5 displays or
7 video sources can be switched in turn to 1 display.
The KVM Switch feature can be set-up to select and control up to 7 remote
computers from a single workstation; 49 remote computers in an expanded
system.

2 ORION LC Installation and Operations Manual
Features


 Dip switch settings easily configured the unit to operate as a:
7-port repeater
8-port Cross-point switch
7:1 KVM switch


 Port switching is performed using commands to the serial port or the
push-button on the unit (Cross-point and KVM switch)


 Supports
DVI-D graphic cards / monitors
USB keyboard (KVM transmitter and receiver units)
USB mouse (KVM transmitter and receiver units)
Serial and audio options available
18 or 24 Bit color


 Extends distance up to 460 feet (140m) using CATx cable
650 feet (200m) using 62.5µ Multimode fiber cable
1,312 feet (400m) using 50µ Multimode fiber cable
32,800 feet (10km) using 9µ Singlemode fiber cable


 (KVM transmitter to Orion LC = 400’ /
Orion LC to KVM receiver = 400’)


 Uses CATx or fiber cabling for all connections


 Maximum DVI resolution 1920 x 1200 @ 60Hz


 LED indicators show link and power status


 Rack mount kits available for mounting in a 19” rack
Compatibility


 Video – Digital Video (DVI-D)


 Keyboard – All USB standard keyboards. Keyboards with built-in USB
hubs are also supported (maximum of two HID devices supported)


 Mouse – USB 2-button, 3-button, and wheel
The Orion LC, when used with USB transmitters and receivers only supports
USB keyboards and mice. Other USB HID devices such as touch screens,
graphic tablets, barcode readers, or other similar devices may function
properly, but are not guaranteed. Only two USB devices are simultaneously
supported. A USB hub is supported but still only two devices are supported.

ORION LC Installation and Operations Manual 3
DDC Information
The Orion LC uses an internal DDC table that is compatible with the majority
of the connected monitors. This table normally does not need changing for
proper operation. It the default setting does not satisfy your system
requirements, the DDC information can be obtained from either the local or
remote monitor. See Appendix G for instructions.
Next Frame Switching
The transmission of screen data is not synchronous to the screen changes
of the graphic card. Normally, the transmission is terminated during the
display of a frame on the screen (at the remote unit). If the device switches
to the new frame during the displaying period of the old frame (somewhere
on the screen), it is possible that you will see horizontal screen breaks at the
moment of switching (default). On the other hand, if the device idles until the
actual frame is displayed completely (until VSYNC) then the number of
frames per second transmitted reduces. To modify the switching behavior,
refer to Appendix G.
KVM Transmitter and Receiver information
The configuration of the CATx or fiber extender transmitters and receivers
used will depend on the application.
Standard Models
Local Remote
Serial / Audio Models
Local Remote Description
USB local
access
CRK-2DTXUD1D CRK-2DTXUD1D/AUD
USB Dual head
Local access
CRK-2DTXUD2D CRK-2DTXUD2D/AUD
The KVM extenders to use with each Orion LC application
(Multiplex Repeater, Cross-point switch, or KVM switch)
will depend on the application and if serial and audio are needed.

Installation
4 ORION LC Installation and Operations Manual
Installation Selection
The Orion LC can be configured to perform three different functions: a
multiplex repeater, a cross-point switch, or a KVM switch. Refer to the
appropriate section for your installation. Use care when connecting the
CATx or fiber cables and do not connect an output to another output.
NOTE: Installation diagrams show CATx models only, fiber installation is
performed the same as the CATx installation.
Multiplex Repeater
Multiplex Repeater Installation 1 x 7
The 1 x 7 configuration allows you to connect one computer to the Orion LC
and display the video on up to 7 DVI monitors.
Set the dip switches and CATx or fiber cabling as shown below.
Set the dip switches so that switch
1, 2, 3, 4, and 5 are all in the
“OFF” position.
Connector labeled “T” connects to
a KVM CATx or fiber transmitter.
Connectors labeled “R” connect to
a KVM CATx or fiber receivers.
(Local keyboard, monitor, and mouse not shown)
Connect a DVI MM cable from the
CPU DVI graphic card to the DVI-
In port on the transmitter
Connect a single CATx or fiber
cable from the transmitter to the
Orion LC port labeled “T”.
Connect up to 7 CATx or fiber
cables from the Orion LC ports
labeled “R” to the receivers.
Connect a DVI monitor to each
receiver’s DVI output
Figure 1. 1x7 Multiplex Receiver
Set Dip switch 1 and 2 to the “OFF” position
to function as a Multiplex Repeater
Receivers
Orion LC
Transmitter
DVI Video Cable
CATx or fiber Cable

ORION LC Installation and Operations Manual 5
Multiplex Repeater Installation 2 x 3
The 2 x 3 configuration allows you to connect two computers to the Orion
LC and display the video of each to 3 DVI monitors.
To configure Orion LC for a 2 input, 3 output Multiplex Repeater, set the dip
switches and CATx or fiber cabling as shown below. Video received at the
T1 input is transmitted out of the three R1 outputs, T2 input out the R2
outputs.
Set the dip switches so that switch
1, 2, 4, and 5 are all in the “OFF”
position, switch 3 in the “ON”
position.
Each connectors labeled “T” (2)
connects to a KVM CATx or fiber
transmitter.
Connectors labeled “R” (6)
connect to KVM CATx or fiber
receivers.
(Local keyboard, monitor, and mouse not shown)
Connect a DVI MM cable from the
each CPU DVI graphic card to the
DVI-In port on the transmitters
Connect a single CATx or fiber
cable from the transmitters to the
Orion LC ports labeled “T1” and
“T2”.
Connect up to 3 CATx or fiber
cables from the Orion LC ports
labeled “R1” and 3 from “R2” to
the receivers.
Connect a DVI monitor to each
receiver’s DVI output.
Figure 2. Multiplex Repeater 2x3
The video source can be from two computers as shown or from a single
computer with a dual video card. The Transmitters can be two single video
models as shown or one dual video model.
Receivers
Orion LC
Transmitters
DVI Video Cable
CATx or fiber Cable

6 ORION LC Installation and Operations Manual
Multiplex Repeater Installation 4 x 4
The 4 x4 configuration allows you to connect four computers to the Orion LC
and display the video of each on a DVI monitor.
To configure Orion LC for a 4 input, 4 output Multiplex Repeater, set the dip
switches and CATx or fiber cabling as shown below. Video received at the
T1 input is transmitted out the R1 output, T2 input out the R2 output, etc.
Set the dip switches so that switch
1, 2, 3, and 5 are all in the “OFF”
position, switch 4 in the “ON”
position.
Each CATx or fiber connector
labeled “T1-4” connects to a KVM
CATx or fiber transmitter.
Connectors labeled “R1-4”
connect to a KVM CATx or fiber
receiver.
(Local keyboard, monitor, and mouse not shown)
Connect a DVI MM cable from
each CPU DVI graphic card to the
DVI-In port on the transmitters
(1-4)
Connect a single CATx or fiber
cable from the transmitters to the
Orion LC ports labeled “T1-4”.
Connect a CATx or fiber cable
from the Orion LC ports labeled
“R1-4” to the receivers.
Connect a DVI monitor to each
receiver’s DVI output
Figure 3. Multiplex Repeater 4x4
The top row of RJ45 connectors has
two LEDs which indicate the LINK
status for the top and bottom RJ45
port. The left LED is for the bottom
RJ45 port status, the right LED is for
the top RJ45 port status.
Orange = Ok
Off = No link
Transmitters
Receivers
Orion LC
DVI Video Cable
CATX Cables

ORION LC Installation and Operations Manual 7
If additional remote displays are needed, the Orion LC, configured as a
Multiplex Repeater, can be cascaded to add up to a maximum of 49 remote
displays. Only one cascaded level is allowed.
The versatility of the Multiplex Repeater in a cascaded configuration allows
for arranging multiple displays in a variety of arrangements. In the below
example, the master unit is cascaded to two additional secondary units. The
remaining five unused outputs on the master can be connected to additional
receivers and displays or cascaded to other Orion LC units.
The primary master unit is set with dip switch #8 off and all cascaded
secondary units are set with dip switch #8 in the on position.
Figure 4. Multiplex Repeater (Cascaded configuration)
Master – Switch #8 OFF
Secondary #1 – Switch #8 ON Secondary #2 – Switch #8 ON
Transmitter
Receivers
DVI Video Cable
CATx or fiber Cable

8 ORION LC Installation and Operations Manual
CrystalView DVI CATx transmitter and receiver for use with the Multiplex
Repeater function.
Multiplex Repeater Operation
The operation of the Orion LC as a Multiplex Repeater is very easy. Once
all cabling is in place and the Orion LC units configured for your application,
the only operating procedure is selecting the video to present on all
monitors. In a 1 x 7 configuration, the single video source is displayed on all
monitors. A 2 x 3 configuration has two video sources, each displayed on
three monitors. A 4 x 4 configuration has four video sources, each
displayed on a single monitor. Cascading the system allows you to present
the video on additional monitors.
In the Multiplex Repeater mode, the push button has no effect. Video is
repeated from the source to the monitors.

ORION LC Installation and Operations Manual 9
Crosspoint-Switch Installation
The Crosspoint-switch feature allows you to route any input video signal to
any output. The unit is first configured to designate the number of video
inputs (+ audio option). If you have 1 video input, the unit is configured as a
1x7 Crosspoint switch; 2 video inputs as a 2x6, etc. As you can see the
RJ45 ports can be configured as either an input or an output. The Dip
switch settings configure the unit as a Crosspoint switch and define the
inputs and outputs. Switching the assigned input to an output is
accomplished using a serial communication program. See the end of this
section for examples. Use care when connecting the CATx or fiber cables
and do not connect an output to another output.
Crosspoint-Switch Installation – 1 x 7
The 1 x 7 configuration allows you to connect one computer to the Orion LC
and display the video on up to 7 DVI monitors.
To configure Orion LC for a 1 input, 7 output Crosspoint switch, set the dip
switches and CATx or fiber cabling as shown below.
The 1 x 7 configuration allows
you to connect 1 computer to the
Orion LC and display the video
(+audio option) on up to 7 DVI
monitors.
To configure Orion LC for a 1
input, 7 output Cross-Point
Switch, set the dip switch 1 ON
and 2-5 OFF and connect the
CATx or fiber cabling as shown.
Connect a DVI MM video cable from
the CPU’s DVI graphic card to the
DVI-In port on the transmitter.
Connect a single CATx or fiber cable
from the transmitter to the Orion LC
port labeled “T”.
Connect up to 7 CATx or fiber
cables from the Orion LC ports
labeled “R” to the receivers.
Connect a DVI monitor to each
receiver’s DVI output
Figure 5. Crosspoint-Switch 1 x 7

10 ORION LC Installation and Operations Manual
Crosspoint-Switch Installation – 2 x 6
The 2 x 6 configuration allows you to connect two computers to the Orion
LC and display the video on up to 6 DVI monitors.
To configure Orion LC for a 2 input, 6 output Crosspoint switch, set the dip
switches and CATx or fiber cabling as shown below.
The 2 x 6 configuration allows
you to connect 2 computer to
the Orion LC and display the
video (+audio option) on up to
6 DVI monitors.
To configure Orion LC for a 2
input, 6 output Cross-Point
Switch, set the dip switch 1 and
3 ON and 2, 4, and 5 OFF and
connect the CATx or fiber
cabling as shown.
Connect a DVI MM video cable
from the CPU’s DVI graphic cards
to the DVI-In ports on the
transmitter.
Connect 2 CATx or fiber cables
from the transmitters to the two
Orion LC port labeled “T”.
Connect up to 6 CATx or fiber
cables from the Orion LC ports
labeled “R” to the receivers.
Connect a DVI monitor to each
receiver’s DVI output
Figure 6. Cross Point Switch - 2 x 6
The 2 x 6 configuration allows you to route the video from either computer to
any connected monitor. In the above example, computer #1’s video is
displayed on 4 monitors and computer #2’s video is displayed on 2
monitors.
The serial switching command for this configuration is:
0x02, 0x47, 0x81, 0x81, 0x03 (Switch output 1 to input 1)
0x02, 0x47, 0x83, 0x81, 0x03 (Switch output 3 to input 1)
0x02, 0x47, 0x82, 0x82, 0x03 (Switch output 2 to input 2)
0x02, 0x47, 0x84, 0x82, 0x03 (Switch output 4 to input 2)
0x02, 0x47, 0x85, 0x82, 0x03 (Switch output 5 to input 2)
0x02, 0x47, 0x86, 0x82, 0x03 (Switch output 6 to input 2)

ORION LC Installation and Operations Manual 11
Crosspoint-Switch Installation – 3 x 5
The 3 x 5 configuration allows you to connect three computers to the Orion
LC and display the video on up to 5 DVI monitors.
To configure Orion LC for a 3 input, 5 output Crosspoint switch, set the dip
switches and CATx or fiber cabling as shown below.
The 3 x 5 configuration allows
you to connect 3 computers to
the Orion LC and display the
video (+audio option) on up to 5
DVI monitors.
To configure Orion LC for a 3
input, 5 output Cross-Point
Switch, set the dip switch 1 and
4 ON and 2, 3, and 5 OFF and
connect the CATx or fiber
cabling as shown.
Connect a DVI MM video cable from
the CPU’s DVI graphic cards to the
DVI-In ports on the transmitters.
Connect 3 CATx or fiber cables from
the transmitters to the three Orion
LC port labeled “T”.
Connect up to 5 CATx or fiber
cables from the Orion LC ports
labeled “R” to the receivers.
Connect a DVI monitor to each
receiver’s DVI output.
Figure 7. Cross Point Switch - 3 x 5
The 3 x 5 configuration allows you to route the video from either computer to
any connected monitor. In the above example, computer #1’s video is
displayed on 3 monitors and computer #2’s video is displayed on 1 monitor
and computer #3’s video is displayed on 1 monitor.
The serial switching commands for this configuration is:
0x02, 0x47, 0x82, 0x81, 0x03 (Switch output 2 to input 1)
0x02, 0x47, 0x84, 0x81, 0x03 (Switch output 4 to input 1)
0x02, 0x47, 0x85, 0x81, 0x03 (Switch output 5 to input 1)
0x02, 0x47, 0x81, 0x82, 0x03 (Switch output 1 to input 2)
0x02, 0x47, 0x83, 0x83, 0x03 (Switch output 3 to input 3)

12 ORION LC Installation and Operations Manual
Crosspoint-Switch Installation – 4 x 4
The 4 x 4 configuration allows you to connect four computers to the Orion
LC and display the video on up to 4 DVI monitors.
To configure Orion LC for a 4 input, 4 output Crosspoint switch, set the dip
switches and CATx or fiber cabling as shown below.
The 4 x 4 configuration allows
you to connect 4 computers to
the Orion LC and display the
video (+audio option) on up to 4
DVI monitors.
To configure Orion LC for a 4
input, 4 output Cross-Point
Switch, set the dip switch 1, 3,
and 4 ON and 2 and 5 OFF and
connect the CATx or fiber
cabling as shown.
Connect a DVI MM video cable from
the CPU’s DVI graphic cards to the
DVI-In ports on the transmitters.
Connect 4 CATx or fiber cables from
the transmitters to the 4 Orion LC
port labeled “T”.
Connect up to 4 CATx or fiber
cables from the Orion LC ports
labeled “R” to the receivers.
Connect a DVI monitor to each
receiver’s DVI output.
Figure 8. Cross Point Switch - 4 x 4
The 4 x 4 configuration allows you to route the video from any computer to
any connected monitor. In the above example, computer #1’s video is
displayed on 1 monitor, computer #2’s video is displayed on 1 monitor,
computer #3’s video is displayed on 1 monitor, and computer #4’s video is
displayed on 1 monitor.
The serial switching commands for this configuration is:
0x02, 0x47, 0x81, 0x81, 0x03 (Switch output 1 to input 1)
0x02, 0x47, 0x82, 0x82, 0x03 (Switch output 2 to input 2)
0x02, 0x47, 0x83, 0x83, 0x03 (Switch output 3 to input 3)
0x02, 0x47, 0x84, 0x84, 0x03 (Switch output 4 to input 4)

ORION LC Installation and Operations Manual 13
Crosspoint-Switch Installation – 5 x 3
The 5 x 3 configuration allows you to connect five computers to the Orion
LC and display the video on up to 3 DVI monitors.
To configure Orion LC for a 5 input, 3 output Crosspoint switch, set the dip
switches and CATx or fiber cabling as shown below.
The 5 x 3 configuration allows
you to connect 5 computers to
the Orion LC and display the
video (+audio option) on up to 3
DVI monitors.
To configure Orion LC for a 5
input, 3 output Cross-Point
Switch, set the dip switch 1and 5
ON and 2, 3, and 4 OFF and
connect the CATx or fiber
cabling as shown.
Connect a DVI MM video cable from
the CPU’s DVI graphic cards to the
DVI-In ports on the transmitters.
Connect 5 CATx or fiber cables from
the transmitters to the five Orion LC
port labeled “T”.
Connect up to 3 CATx or fiber
cables from the Orion LC ports
labeled “R” to the receivers.
Connect a DVI monitor to each
receiver’s DVI output.
Figure 9. Cross Point Switch - 5 x 3
The 5 x 3 configuration allows you to route the video from any of the 5
computers to any connected monitor. In the above example, computer #1’s
video is displayed on 1 monitor, computer #2’s video is displayed on 1
monitor, computer #3’s video is displayed on 1 monitor, and computer #4
and #5 are not connected to a monitor. Issuing serial commands can route
any selected computer to any of the connected monitors.
The serial switching commands for this configuration is:
0x02, 0x47, 0x81, 0x81, 0x03 (Switch output 1 to input 1)
0x02, 0x47, 0x82, 0x82, 0x03 (Switch output 2 to input 2)
0x02, 0x47, 0x83, 0x83, 0x03 (Switch output 3 to input 3)
(Input 4 and 5 are not displayed)

14 ORION LC Installation and Operations Manual
Crosspoint-Switch Installation – 6 x 2
The 6 x 2 configuration allows you to connect six computers to the Orion LC
and display the video on up to 2 DVI monitors.
To configure Orion LC for a 6 input, 2 output Crosspoint switch, set the dip
switches and CATx or fiber cabling as shown below.
The 6 x 2 configuration allows
you to connect 6 computers to
the Orion LC and display the
video (+audio option) on up to 2
DVI monitors.
To configure Orion LC for a 6
input, 2 output Cross-Point
Switch, set the dip switch 1, 3,
and 5 ON and 2 and 4 OFF and
connect the CATx or fiber
cabling as shown.
Connect a DVI MM video cable from
the CPU’s DVI graphic cards to the
DVI-In ports on the transmitters.
Connect 6 CATx or fiber cables from
the transmitters to the six Orion LC
port labeled “T”.
Connect up to 2 CATx or fiber
cables from the Orion LC ports
labeled “R” to the receivers.
Connect a DVI monitor to each
receiver’s DVI output.
Figure 10. Cross Point Switch - 6 x 2
The 6 x 2 configuration allows you to route the video from any of the 6
computers to any connected monitor. In the above example, computer #1’s
video is displayed on 1 monitor, computer #2’s video is displayed on 1
monitor, and computer #3, #4, #5, and #6 are not connected to a monitor.
Issuing serial commands can route any selected computer to any of the
connected monitors.
The serial switching commands for this configuration is:
0x02, 0x47, 0x81, 0x81, 0x03 (Switch output 1 to input 1)
0x02, 0x47, 0x82, 0x82, 0x03 (Switch output 2 to input 2)
(Inputs 3, 4, 5, 6, and 7 are not displayed)