Rosemount 702 User manual

www.rosemount.com
Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702 Wireless Discrete Transmitter

Reference Manual
00809-0200-4702, Rev BA
June 2010 Rosemount 702
Rosemount 702 WirelessHART
Discrete Transmitter
Rosemount 702 Hardware Revision
HART®Device Revision
Field Communicator Field Device Revision
1
1
Dev v1, DD v4
NOTICE
Read this manual before working with the product. For personal and system safety, and for
optimum product performance, make sure to thoroughly understand the contents before
installing, using, or maintaining this product.
The United States has two toll-free assistance numbers and one international number.
Customer Central
1 800 999 9307 (7:00 a.m. to 7:00 p.m. CST)
National Response Center
1 800 654 7768 (24 hours a day)
Equipment service needs
International
1 952 906 8888
The products described in this document are NOT designed for nuclear-qualified
applications.
Using non-nuclear qualified products in applications that require nuclear-qualified hardware
or products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact an Emerson Process
Management Sales Representative.

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
The power module with the wireless unit contains two “C” size primary lithium/thionyl chloride
batteries. Each battery contains approximately 2.5 grams of lithium, for a total of 5 grams in each
pack. Under normal conditions, the battery materials are self-contained and are not reactive as
long as the batteries and the pack integrity are maintained. Care should be taken to prevent
thermal, electrical or mechanical damage. Contacts should be protected to prevent premature
discharge.
Battery hazards remain when cells are discharged.
Power modules should be stored in a clean and dry area. For maximum battery life, storage
temperature should not exceed 30° C.
The power module has surface resistivity greater than one gigaohm and must be properly
installed in the wireless device enclosure. Care must be taken during transportation to and from
the point of installation to prevent electrostatic charge build-up.
Explosions could result in death or serious injury:
Installation of this transmitter in an explosive environment must be in accordance
with the appropriate local, national, and international standards, codes, and
practices. Please review the approvals section of the 702 Reference Manual for any
restrictions associated with a safe installation.
• Before connecting a Field Communicator in an explosive atmosphere, ensure the
instruments are installed in accordance with intrinsically safe or non-incendive
field wiring practices
Process leaks may cause harm or result in death:
• Install and tighten process connectors before applying pressure
Electrical shock can result in death or serious injury:
• Avoid contact with the leads and terminals. High voltage that may be present on
leads can cause electrical shock
NOTICE
The Rosemount 702 and all other wireless devices should be installed only after the
Smart Wireless Gateway has been installed and is functioning properly. Wireless
devices should also be powered up in order of proximity from the Smart Wireless
Gateway, beginning with the closest. This will result in a simpler and faster network
installation.
NOTICE
Shipping considerations for wireless products:
The unit was shipped to you without the power module installed. Please remove the power
module prior to shipping.
Each power module contains two “C” size primary lithium batteries. Primary lithium batteries
are regulated in transportation by the U. S. Department of Transportation, and are also
covered by IATA (International Air Transport Association), ICAO (International Civil Aviation
Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the
responsibility of the shipper to ensure compliance with these or any other local
requirements. Please consult current regulations and requirements before shipping.

Reference Manual
00809-0200-4702, Rev BA
June 2010 Rosemount 702
1
SECTION 1
Overview Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
702 Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Wireless Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Mechanical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Product Recycling/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
SECTION 2
Configuration Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Switch Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Device Sensor Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Device Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Dry Contact Inputs, Measurement Option Code 22. . . . . . . . . . . . 2-3
Liquid Hydrocarbon Detection, Measurement Option Code 61 . . . 2-4
HART Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Dry Contact Inputs, Measurement Option Code 22. . . . . . . . . . . . 2-5
Liquid Hydrocarbon Detection, Measurement Option Code 61 . . . 2-6
Fast Key Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Remove Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
SECTION 3
Mounting, Wiring
Switches, and
Sensors
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Direct Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Remote Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Wiring Switches and Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Dry Contact Inputs, Measurement Option Code 22. . . . . . . . . . . . 3-5
Wireless Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Liquid Hydrocarbon Detection, Measurement Option Code 61 . . . 3-7
LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Ground the Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
SECTION 4
Commissioning Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Verify Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
AMS Wireless Configurator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Table of Contents

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
2
SECTION 5
Operation and
Maintenance
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Wireless Discrete Output from Switches and Sensors. . . . . . . . . . . . . 5-2
Dry Contact Inputs, Measurement Option Code 22. . . . . . . . . . . . 5-2
Wireless Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Liquid Hydrocarbon Detection, Measurement Option Code 61 . . . 5-5
LCD Screen Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Startup Screen Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Diagnostic Button Screen Sequence . . . . . . . . . . . . . . . . . . . . . . 5-10
Network Diagnostic Status Screens. . . . . . . . . . . . . . . . . . . . . . . 5-11
Device Diagnostic Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Power Module Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
APPENDIX A
Specifications and
Reference Data
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Physical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Wireless Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Other Options (Include with selected model number) . . . . . . . . . . A-4
APPENDIX B
Product
Certifications
Approved Manufacturing Locations . . . . . . . . . . . . . . . . . . . . . . . . B-1
Telecommunication Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
European Union Directive Information. . . . . . . . . . . . . . . . . . . . . . B-1
Ordinary Location Certification for FM . . . . . . . . . . . . . . . . . . . . . . B-1
Hazardous Locations Certificates . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Reference Manual
00809-0200-4702, Rev BA
June 2010
1-1
Rosemount 702
Section 1 Overview
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1-1
702 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1-1
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1-2
Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1-5
Product Recycling/Disposal . . . . . . . . . . . . . . . . . . . . . . .page 1-5
SAFETY MESSAGES Instructions and procedures in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
Warnings
702 TRANSMITTER Features of the Rosemount 702 include:
• An installation-ready solution that provides a variety of mounting
options, transmitter configurations, and switches
• Flexibility to meet your most demanding applications
• Wireless output with >99% data reliability delivers rich HART®data,
protected by industry leading security
• Single or dual switch input with logics for limit contact and opposing
contact applications
• The integral LCD conveniently displays the primary switch input and
diagnostics of the transmitter
• Simple and easy installation practices currently being used for robust
installations
Failure to follow these installation guidelines could result in death or serious injury:
• Only qualified personnel should perform the installation
Explosions could result in death or serious injury.
• Before connecting a Field Communicator in an explosive atmosphere, make
sure that the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications
Process leaks could result in death or serious injury.
• Do not remove the switch while in operation
• Install and tighten switches before applying pressure
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
1-2
CONSIDERATIONS
General Switches produce either an open or closed signal. By using simple HART
configuration, the Rosemount 702 converts the switch signal to a
wireless-enabled signal.
Wireless Considerations Power Up Sequence
The power module should not be installed on any wireless device until the
Smart Wireless Gateway (“Gateway”) is installed and functioning properly.
Wireless devices should also be powered up in order of proximity from the
Gateway, beginning with the closest. This will result in a simpler and faster
network installation. Enable Active Advertising on the Gateway to ensure that
new devices join the network faster. For more information see the Smart
Wireless Gateway Manual (Document Number 00809-0200-4420).
Antenna Position
The antenna should be positioned vertically, either straight up or straight
down, and it should be approximately 3 ft. (1 m) from any large structure,
building, or conductive surface to allow for clear communication to other
devices.
Figure 1-1. Antenna Position
Conduit Entries
Upon installation, ensure that each conduit entry is either sealed with a
conduit plug with appropriate thread sealant, or has an installed conduit fitting
or cable gland with appropriate thread sealant.

Reference Manual
00809-0200-4702, Rev BA
June 2010
1-3
Rosemount 702
Figure 1-2. Conduit Entries
Field Communicator Connections
The Power Module needs to be connected for the Field Communicator to
interface with the 702.
Figure 1-3. Field Communicator
Connections
Mechanical Location
When choosing an installation location and position, take into account access
to the transmitter. For best performance, the antenna should be vertical with
space between objects in a parallel metal plane, such as a pipe or metal
framework, as the pipes or framework may adversely affect the antenna’s
performance.
Conduit Entry
Conduit Entry
COMM
P/N00753-9200-0020
1
2
3
4

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
1-4
Electrical Power Module
The Rosemount 702 WirelessHART™ transmitter is self-powered. The
included power module contains two “C” size primary lithium/thionyl chloride
batteries. Each battery contains approximately 2.5 grams of lithium, for a total
of 5 grams in each pack. Under normal conditions, the battery materials are
self-contained and are not reactive as long as the batteries and the power
module are maintained. Care shouldbe taken to prevent thermal, electrical, or
mechanical damage. Contacts should be protected to prevent premature
discharge.
Use caution when handling the power module, it may be damaged if dropped
from heights in excess of 20 feet (6.10 m).
Switch
Make switch connections through the cable entry in the side of the connection
head. Be sure to provide adequate clearance for cover removal.
Environmental Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Temperature Effects
The transmitter will operate within specifications for ambient temperatures
between -40 and 185 °F (-40 and 85 °C). Heat from the process is transferred
from the switch to the transmitter housing. If the expected process
temperature is near or beyond specification limits, consider using an
extension, or remote mount the transmitter to thermally isolate it from the
process.
Figure 1-1 provides an example of the relationship between the transmitter
housing temperature rise and the extension length.
Figure 1-4. Figure 1-1.
Rosemount 702 Transmitter
Connection Head Temperature
Rise vs. Extension Length
Housing Temperature Rise, Above
Ambient °C (°F)
3 4 5 6 7 8 9
0
60 (108)
50 (90)
40 (72)
30 (54)
20 (36)
10 (18)
4.2
55
Extension Length (in.)
815 °C (1500 °F) Process Temperature
540 °C (1000 °F) Process Temperature
250 °C (482 °F) Process Temperature

Reference Manual
00809-0200-4702, Rev BA
June 2010
1-5
Rosemount 702
Example
The transmitter specification limit is 185 °F (85 °C). If the ambient temperature
is 131 °F (55 °C) and the maximum process temperature to be measured is
1500 °F(815 °C), the maximum permissible connection head temperature rise
is the transmitter specification limit minus the ambient temperature (moves
185 °F to 131°F [85 to 55 °C]), or 86 °F (30°C).
In this case, an extension of 5-in. (0.13 m) meets t his requirement, but 6-in.
(0.15 m) provides an additional margin of protection, thereby reducing risk of
ambient thermal damage.
Temperature Limits
SERVICE SUPPORT To expedite the return process outside of North America, contact your
Emerson Process Management representative,
Within the United States, call the Emerson Process Management Response
Center toll-free number 1 800 654 7768. The center, which is available 24
hours a day, will assist you with any needed information or materials.
The center will ask for product model and serial numbers, and will provide a
Return Material Authorization (RMA) number. The center will also ask for the
process material to which the product was last exposed.
SHIPPING CONSIDERATIONS FOR WIRELESS PRODUCTS (LITHIUM
BATTERIES):
The unit was shipped with the Power Module not installed. Please remove the
Power Module from the unit before shipping.
Primary lithium batteries (charged or discharged) are regulated during
transportation by the U.S. Department of Transportation. They are also
covered by IATA (International Air Transport Association), ICAO (International
Civil Aviation Organization), and ARD (European Ground Transportation of
Dangerous Goods). It is the responsibility of the shipper to ensure compliance
with these or any other local requirements. Consult current regulations and
requirements before shipping.
PRODUCT
RECYCLING/DISPOSAL Recycling of equipment and packaging should be taken into consideration
and disposed of in accordance with local and national legislation/regulations.
Operating Limit Storage Limit
With LCD Display -4 to 175 °F
-20 to 80° C -40 to 185 °F -40 to 85 °C
Without LCD Display -40 to 185 °F
-40 to 85° C -40 to 185 °F -40 to 85 °C
Individuals who handle products exposed to a hazardous substance can avoid injury if they
are informed of, and understand, the hazard. If the product being returned was exposed to a
hazardous substance as defined by OSHA, a copy of the required Material Safety Data
Sheet (MSDS) for each hazardous substance identified must be included with the returned
goods.

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
1-6

Reference Manual
00809-0200-4702, Rev BA
June 2010
2-1
Rosemount 702
Section 2 Configuration
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2-1
Device Sensor Configuration . . . . . . . . . . . . . . . . . . . . . .page 2-2
Device Network Configuration . . . . . . . . . . . . . . . . . . . . .page 2-3
Remove Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2-7
SAFETY MESSAGES Instructions and procedures in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
Warnings
Failure to follow these installation guidelines could result in death or serious injury:
• Only qualified personnel should perform the installation
Explosions could result in death or serious injury.
• Before connecting a Field Communicator in an explosive atmosphere, make
sure that the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications
Process leaks could result in death or serious injury.
• Do not remove the switch while in operation
• Install and tighten switches before applying pressure
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
2-2
Switch Connections The 702 is compatible with a number of simple switches. When ordered in the
optional configuration for Liquid Hydrocarbon Detection, option code 61, the
702 is compatible with Tyco®TraceTek®Fast Fuel Sensors and TraceTek
sensing cable. Figure 2-1 on page 2-3 shows the correct input connections to
the switch terminals on the transmitter. To ensure a proper switch connection,
anchor the switch lead wires into the appropriate compression terminals and
tighten the screws.
Switch Leads
If the switch is installed in a high-voltage environment and a fault condition or
installation error occurs, the sensor leads and transmitter terminals could
carry lethal voltage. Use extreme caution when making contact with the leads
and terminals.
Use the following steps to wire the sensor and power supply to the
transmitter:
1. Remove the transmitter enclosure cover (if applicable).
2. Attach the sensor leads according to the wiring diagram Figure 3-3 on
page 3-4.
3. Connect the power module.
4. Verify the connection by viewing the LCD.
5. Replace the cover and tighten (if applicable).
DEVICE SENSOR
CONFIGURATION Remove the power module-side housing cover to expose the terminal block
and HART communication terminals, then connect the power module to
power the unit for configuration.
The Rosemount 702 will receive any HART communication from a handheld
Field Communicator, or AMS Wireless Configurator. When using a Field
Communicator, any configuration changes must be sent to the transmitter
using the Send key (F2). AMS Wireless Configurator configuration changes
are implemented when the Apply button is clicked.
AMS Wireless Configurator
AMS Wireless Configurator is capable of connecting to devices directly, using
a HART modem, or with the Gateway. When configuring on the bench with a
HART modem, double click the device icon, then choose the Configure/Setup
tab (or right click and select Configure/Setup). Configure the device settings
using the Direct Connection menu. When configuring with the Gateway,
double click the device icon then choose the Configure/Setup tab (or right
click and select Configure/Setup). Configure the device settings using the
Wireless Connection menu.
To check or change sensor configuration using a Field Communicator, enter
the following Fast Key Sequence: 2, 2, 2.

Reference Manual
00809-0200-4702, Rev BA
June 2010
2-3
Rosemount 702
DEVICE NETWORK
CONFIGURATION To communicate with the Gateway, and ultimately the Information System, the
transmitter must be configured to communicate with the wireless network.
Using a Field Communicator or AMS Wireless Configurator, enter the
Network ID and Join Key so they match the Network ID and Join Key of the
Gateway and the other devices in the network. If the Network ID and Join Key
are not identical, the transmitter will not communicate with the network. The
Network ID and Join Key may be obtained from the Gateway on the
Setup>Network>Settings page on the web server. Using a Field
Communicator, the Network ID can be configured by entering the Fast Key
Sequence: 2, 2, 1, 1. The Join Key can also be configured using a Field
Communicator with the Fast Key Sequence: 2, 2, 1, 2.
The final device network configuration piece is the Update Rate which, by
default, is 1 minute. It can be changed at commissioning, or at any time, by
using AMS Wireless Configurator or the Gateway’s web server. The Update
Rate should be between 8 seconds and 60 minutes. To change the Update
Rate with a Field Communicator, use the Fast Key Sequence: 2, 2, 1, 3.
If doing a bench top initial configuration, after completion remove the power
module until installation. When the device is installed, insert he power module
and close the housing cover securely. Always ensure a proper seal so that
metal touches metal, but do not over tighten.
Dry Contact Inputs,
Measurement Option
Code 22
Figure 2-1. 702 Terminal Block
Connect the HART communication leads to the COMM terminals on the
terminal block.
1
2
4
3

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
2-4
Liquid Hydrocarbon
Detection, Measurement
Option Code 61
Terminal Block Connections
Figure 2-2. Fuel Sensor
Terminal Diagram
Connect Tyco TraceTek and Fast Fuel sensor lead wires by matching the
colors of wires to colors on terminal block.
Figure 2-3. Field Communicator
Connections
For HART communication, a 702 DD is required.
COMM
P/N00753-9200-0020
1
2
3
4

Reference Manual
00809-0200-4702, Rev BA
June 2010
2-5
Rosemount 702
HART MENU TREE For ease of operation, changing setup, such as switch type, can be completed
in several locations.
Dry Contact Inputs, Measurement Option Code 22
Figure 2-4. Field Communicator Menu Tree, DD Revision 2
1. Overview
2. Configure
3. Service Tools
1. Active Alerts
2. Communication Status
3. Discrete Input 1
4. Discrete 1 Status
5. Discrete Input 2
6. Discrete 2 Status
7. Last Update Time
8. DD Version
1. Guided Setup
2. Manual Setup
1. Alerts
2. Variables
3. Communications
4. Maintenance
5. Simulate
1. Join Device to Network
2. Configure Update Rate
3. Configure Discrete Application
4. Configure Device Display
1. Wireless
2. Discrete Sensors
3. Electronics Temperature
4. Device Information
5. Device Display
6. Other
1. Active Alerts
2. History
1. Discrete Input 1
2. Discrete 1 Status
3. Discrete Input 2
4. Discrete 2 Status
5. Electronics Temperature
6. Electronics Temperature Status
7. Supply Voltage
8. Supply Voltage Status
9. Last Update Time
1. Join Status
2. Communication Status
3. Join Mode
4. Number of Available Neighbors
5. Number of Advertisements Heard
6. Number of Join Attempts
1. Sensor Calibration
2. Other
1. Discrete 1
2. Discrete 2
3. Ambient Temperature
4. Supply Voltage
1. Clear Alert History
1. Discrete Input 1 Sensor Wiring Offset
2. Discrete Input 2 Sensor Wiring Offset
1. Perform Master Reset
2. Measurement History
3. Advertise to New Devices
4. Install New Power Module
1. Network ID
2. Join Device to Network
3. Broadcast Rates
4. Power Mode
5. Power Source
1. Configure Discrete Application
2. Discrete Input 1
3. Discrete Input 2
1. Electronics Temperature
2. Electronics Temperature Status
3. Unit
4. Maximum
5. Minimum
1. Tag
2. Long Tag
3. Device
4. Discrete Input 1
5. Discrete Input 2
6. Wireless
7. Write Protect
8. Poll Address
1. Mode
1. Write Protect
2. AC Power Filter
3. Measurement and Status Log
1. Configure Update Rate
2. Message 1
3. Message 2
4. Message 3
1. Discrete State
2. Invert Option
3. Sensor Serial Number
1. Discrete State
2. Invert Option
3. Sensor Serial Number
1. Manufacturer
2. Model
3. Final Assembly Number
4. Universal
5. Field Device
6. Software
7. Hardware
8. Descriptor
9. Message
10 Date
11 Model Number I
12 Model Number II
13 Model Number III
14 SI Unit Restriction
15 Country
16 Device ID
1. Sensor Serial Number
1. Sensor Serial Number
1. Manufacturer
2. Device Type
3. Device Revision
4. Software Revision
5. Hardware Revision

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
2-6
Liquid Hydrocarbon Detection, Measurement Option Code 61
Figure 2-5. Field Communicator Menu Tree, DD Revision 1, for Leak Detection
1. Overview
2. Configure
3. Service Tools
1. Device Status
2. Communication Status
3. Sensor State
4. Sensor Status
5. Update Rate
6. DD Revision
1. Guided Setup
2. Manual Setup
1. Alerts
2. Variables
3. Communications
4. Routine Maintenance
5. Simulate
1. Join Device to Network
2. Configure Update Rate
3. Configure Sensor
1. Wireless
2. Leak Sensor
3. Electronics Temperature
4. Device Information
5. Other
1. Refresh Alerts
2. History
1. Sensor State
2. Sensor Status
3. Electronics Temperature
4. Electronics temperature Status
5. Supply Voltage
6. Supply Voltage Status
7. Last Update Time
1. Join Status
2. Communication Status
3. Join Mode
4. Number of Available Neighbors
5. Number of Advertisements Heard
6. Number of Join Attempts
1. Other
1. Input
2. Electronics Temperature
3. Supply Voltage
1. Perform Master Reset
2. Measurement History
3. Advertise to New Devices
4. Install New Power Module
1. Network ID
2. Join Device to Network
3. Broadcast Rates
1. Configure Sensor
2. Sensor State
3. Sensor Status
4. Sensor Serial Number
1. Electronics Temperature
2. Electronics Temperature Status
3. Unit
4. Maximum
5. Minimum
1. Tag
2. Long Tag
3. Device
4. Leak Sensor
5. Wireless
6. Write Protect
7. Polling Address
1. Write Protect
2. AC Power Filter
3. Measurement and Status Log
4. Power Mode
5. Power Source
1. Configure Update Rate
2. Message 1
3. Message 2
4. Message 3
1. Manufacturer
2. Model
3. Final Assembly Number
4. Universal
5. Field Device
6. Software
7. Hardware
8. Descriptor
9. Message
10 Date
11 Model Number I
12 Model Number II
13 Model Number III
14 SI Unit Restriction
15 Country
16 Device ID
1. Sensor Serial Number
1. Manufacturer
2. Device Type
3. Device Revision
4. Software Revision
5. Hardware Revision
6. Transmit Power Level

Reference Manual
00809-0200-4702, Rev BA
June 2010
2-7
Rosemount 702
Fast Key Sequence Table 2-1 lists the fast key sequence for common transmitter functions.
NOTE:
The fast key sequences assume that a current DD is being used: DD Rev 2
for dry contact inputs, and DD Rev 1 for leak detection.
Table 2-1. 702 Fast Key
Sequence
REMOVE POWER
MODULE After the sensor and network have been configured, remove the power
module and replace the transmitter cover. The power module should be
inserted only when the device is ready for commissioning
Function Key Sequence Menu Items
Device Information 2, 2, 4, 3 Manufacturer, Model, Final Assembly Number,
Universal, Field Device, Software, Hardware
Descriptor, Message, Date, Model Number, I, II,
III, SI Unit Restriction, Country
Guided Setup 2, 1 Join Device to Network, Configure Update Rate,
Configure Sensor, Calibrate Sensor, Configure
Display, Configure Process Alarms
Manual Setup 2, 2 Wireless, Process Sensor, Percent of Range,
Device Temperature, Device Information,
Device Configure, Other
Wireless 2, 2, 1 Network ID, Join Device to Network, Configure
Update Rate, Configure Broadcast Power Level,
Power Mode, Power Source
Discrete Input
Configuration 2, 2, 2 Discrete Input Configuration

Reference Manual
00809-0200-4702, Rev BA
June 2010
Rosemount 702
2-8