Rosewill RC-110 User manual

USB 2.0 + 1394a PCI Adapter RC110
User Manual

1
User Manual
USB 2.0 + 1394a PCI Adapter RC110
Overview
The IEEE1394 multimedia connection (also known as Fire Wire by Apple Computer, and iLink by
Sony) features hot swapping, high-speed performance, peer to peer communication and daisy
chained which can accept up to 63 devices connected simultaneously.
The idea of IEEE1394 standard is all other devices and peripherals that connected outside of PC
can simply plug into 1394 port instead of opening case and adding a circuit board. IEEE1394
standard is an important enabling technology for the emerging multimedia market.
Features
• Chipset: NEC 720101
• Data Transfer Rate: USB 1.1 OHCI 1.5Mbps, 12Mbps
USB 2.0 EHCI 480Mbps
• Bus: PCI 2.2 32-bit, 33MHz,5V
• Connector: NEC USB2.0 4+1PORT 4 external Type A USB ports and 1
internal Type A USB port
• Chipset: NEC single-chip uPD72873 (IEEE 1394 Controller)
VIA VT6212 (USB 2.0 Controller)
• Data Transfer Rate: 1394a 100/200/400Mbps, OHCI 1.1.
USB 1.1 OHCI 1.5Mbps, 12Mbps
USB 2.0 EHCI 480Mbps
• Bus: PCI 2.2 32 bit, 33MHz, 3.3V.
• Connector: 2 external 1394 6-pin connectors.
3 external Type A USB ports and 1 internal Type A USB port
IEEE 1394 Features
• Supports up to 63 devices.
• Supports devices hot swap.
• Supports Power class 0012(1).
• Auxiliary power connector J2/J2-A to increase the power available to 1394a bus to up to
15W.
• MS Windows compatible including DV and SBP-2 drivers, supports all common

2
User Manual
USB 2.0 + 1394a PCI Adapter RC110
camcorders, disk drives, printers and scanners with 1394 interfaces.
• Supports Windows 98, Windows 98SE, Windows ME, Windows 2000 & Windows XP
USB 2.0 Features
• Supports up to 127 devices
• Supports devices hot swap and wake-up
• Output current per port = 500mA (max)
• Supports Windows 98, Windows 98SE, Windows ME, Windows 2000 & Windows XP
Troubleshooting
If your system doesn’t work properly after connecting to a 1394 device, please turn off your
computer. Connect the auxiliary power connector (J2/J2-A) to power supply and then restart
again. If it still doesn’t solve the problem, please refer to the specifications of your 1394 device.
Check the power consumption and make sure it doesn’t exceed 15W.
Driver Installation
Windows ME
Once the IEEE1394 + USB 2.0 Host Adaptor is installed and the computer is restarted, Windows
will detect the board and automatic find the new hardware and install driver for it.
devices in Device Manager.
1. Windows has found new hardware “NEC Firewarden OHCI Compliant IEEE 1394 Host
Controller” and click Next to continue

3
User Manual
USB 2.0 + 1394a PCI Adapter RC110
2. Click “Finish” to continue.
3. Click “Yes” to restart computer.
4. Open the Device Manager and there is a yellow exclamation mark on one of the “VIA Tech
3038 PCI to USB Universal Host Controller” item, then install the driver from the CD-ROM.

4
User Manual
USB 2.0 + 1394a PCI Adapter RC110
5. Insert the driver CD into the CD-ROM drive and select “F:\PCI_IO\VIAUSB20\” (where F is
CD-ROM drive) and run the setup program by double clicking on the “setup.exe” file in this CD.
6. Click Next.

5
User Manual
USB 2.0 + 1394a PCI Adapter RC110
7. Select “Install USB 2.0 Driver” and click Next. Select “Install USB 2.0 Driver” and click
Next.

6
User Manual
USB 2.0 + 1394a PCI Adapter RC110
8. Click Finish to restart the computer.
Thank you for purchasing Rosewill Product.
Please register your product at www.rosewill.com for complete warranty information and future
support for your product.