Rotel RC-1590 User manual

Owner’s Manual
Manuel de l’utilisateur
Bedienungsanleitung
Manual de Instrucciones
Gebruikershandleiding
Manuale di istruzioni
Instruktionsbok
Инструкция пользователя
RC‑1590
Stereo Control Amplier
Amplicateur de Contrôle Stéréo
Stereo‑Vorverstärker
Preamplicador Estereofónico
Stereo‑regelversterker
Preamplicatore Stereo
Stereokontrollförstärkare
Предварительный стерео усилитель
5V 2.1A
PHONO CD XLR TUNER AUX
OPT 1 COAX 1
USB PC-USB
PHONES
POWER
RC-1590
MENU ENTER
OPT 2 OPT 3 COAX 2 COAX 3 BT

2RC‑1590 Stereo Control Amplier
Notice
The RS232 connection should be handled by authorized persons only.
WARNING: There areno user serviceable parts inside.Refer all servicing
to qualified service personnel.
WARNING: Toreduce the risk of fireor electric shock, do not exposethe
unit to moisture or water. Do not expose the unit to dripping or splashing.
Do not place objects filled with liquids, such as vases, on the unit. Do
not allow foreign objects to get into the enclosure. If the unit is exposed
to moisture, or a foreign object gets into the enclosure, immediately
disconnect the power cord from the wall. Take the unit to a qualified
service person for inspection and necessary repairs.
Read all the instructions before connecting or operating the component.
Keep this manual so you can refer to these safety instructions.
Heed all warnings and safety information in these instructions and on
the product itself. Follow all operating instructions.
Clean the enclosure only with a dry cloth or a vacuum cleaner.
Do not use this unit near water.
Do not place the unit on a bed, sofa, rug, or similar surface that could
block the ventilation openings. If the unit is placed in a bookcase or
cabinet, there must be ventilation of the cabinet to allow proper cooling.
Keep the component away from radiators, heat registers, stoves, or any
other appliance that produces heat.
Rotel productsare designed tocomply with international
directives on the Restriction of Hazardous Substances
(RoHS) in electrical and electronic equipment and the
disposal of Waste Electrical and Electronic Equipment
(WEEE). The crossed wheelie bin symbol indicates
compliance andthat the products mustbe appropriately
recycledor processedin accordancewith thesedirectives.
This symbol means that this unit is double insulated.
An earth connection is not required.
Important Safety Instructions
WARNING: The rear panel power cord connector is the mains power
disconnect device. The device must be located in an open area that
allows access to the cord connector.
The unit must be connected to a power supply only of the type and
voltagespecifiedon the rearpanel. (USA: 120 V/60Hz,EC: 230V/50Hz)
Connect the component to the power outlet only with the supplied
power supply cable or an exact equivalent. Do not modify the supplied
cable. A polarized plug has two blades, with one wider than the other. A
grounding plug has two blades plus a third grounding prong. These are
provided for your safety. Do not defeat grounding and/or polarization
safety provisions. If the supplied plug does not fit your outlet, please
consult an electrician for replacement of the obsolete outlet. Do not
use extension cords.
The main plug of the power cordset is a disconnect device of the
apparatus. In order to completely disconnect the apparatus from the
supply mains, the main plug of the power cordset should be unplugged
from the mains (AC) outlet. The standby LED indicator will not be lit
up to show the power cord is unplugged. The disconnect device shall
remain readily operable.
Do not route the power cord where it will be crushed, pinched, bent,
exposed toheat, or damagedin any way. Payparticular attentionto the
power cord at the plug and where the cord exits the back of the unit.
The power cord should be unplugged from the wall outlet during a
lightning storm or if the unit is to be left unused for a long period
of time.
Use only accessories specified by the manufacturer.
Use onlywith a cart,stand, rack,bracket orshelf system
recommended by Rotel. Use caution when moving the
unit in a stand or rack to avoid injury from a tip‑over.
Immediately stop using the component and have it inspected and/
or serviced by a qualified service agency if:
•The power supply cord or plug has been damaged.
•Objects have fallen or liquid has been spilled into the unit.
•The unit has been exposed to rain.
•The unit shows signs of improper operation.
•The unit has been dropped or damaged in any way.
The batteries in theremote control should not be exposedto excessive
temperature such as sunshine, fire or other heat sources.
12
3
Pin Assignments
Balanced Audio (3 pole XLR):
Pin 1: Ground / Screen
Pin 2: In phase / +ve / Hot
Pin 3: Out of phase / ‑ve / Cold

3
English
L
R
L
R
PUSH PUSH
1 2
q=-0
9
i
76
43
8
o [ ] \ s
5
a
we r t
u
y
p
Figure 1: Controls and Connections
Commandes et Branchements
Bedienelemente und Anschlüsse
Controles y Conexiones
Bedieningselementen en aansluitingen
Controlli e connessioni
Kontroller och anslutningar
Органы управления и разъемы

4RC‑1590 Stereo Control Amplier
Figure 2: RR‑AX100 Remote Control
Télécommande infrarouge RR‑AX100
Fernbedienung RR‑AX100
Mando a Distancia RR‑AX100
Afstandsbediening RR‑AX100
Telecomando RR‑AX100
RR‑AX100 fjärrkontroll
Пульт ДУ RR-AX100
RR-AX100
SETUP
B
A
C
D
E
F
I
H
L
N
M
G
K
O
P

5
English
Figure 3: Analog Input and Output Connections
Branchements des entrées et sorties analogiques
Analoge Ein‑ und Ausgangsanschlüsse
Entradas y Salidas Analógicas
Analoge ingangen en uitgangen
Collegamenti ingressi ed uscite analogici
Anslutningar för analoga in‑ och utgångar
Аналоговые входы и выходы
POWER AMPLIFIER
MODEL NO. : RB -1590
POWER CONSUMPTION : 800W
BALANCED
UNBA LANCED
12V TR IGGER
ON
OFF IN OUT
UNBA LANCED U NBALANCED
RIGHT IN PUT LEFT INP UT
BALA NCED BAL ANCED
RIGH T SPEAKE R LEFT SPE AKER
RP-5 53
SPEAKER IMPEDANCE
COMBINED LOAD
4 OHMS MINIMUM
PUSH PUSH
L
R
L
R
PUSH PUSH
PH0N
O
R L GND
ROTEL RCD-1570
ROTEL RC-1590
ROTEL RB-1590

6RC‑1590 Stereo Control Amplier
Figure 4: Balanced (XLR) Input and Output Connections
Branchements des entrées et sorties symétriques (XLR)
Symmetrische Ein‑ und Ausgangsanschlüsse (XLR)
Entradas y Salidas Balanceadas (XLR)
Gebalanceerde ingangen (XLR) en uitgangen
Collegamenti ingressi ed uscite bilanciati (XLR)
Balanserade in‑ och utgångar (XLR)
Балансные (XLR) входы и выходы
POWER AMPLIFIER
MODEL NO. : RB -1590
POWER CONSUMPTION : 800W
BALA NCED
UNBALANCED
12V TRIGGER
ON
OFF IN OUT
UNBALANCED UNBAL ANCED
RIGHT IN PUT LEFT INPUT
BALANCED BALANCED
RIGHT SPEAK ER LEFT SPE AKER
RP-5 53
SPEAKER IMPEDANCE
COMBINED LOAD
4 OHMS MINIMUM
PUSH PUSH
L
R
L
R
PUSH PUSH
ROTEL RCD-1570
ROTEL RC-1590
ROTEL RB-1590

7
English
CD PLAYER
DIGITAL AUDIO OUTPUT
OPTICAL
COAXIAL
Computer
L
R
L
R
PUSH PUSH
ROTEL RCD-1570
ROTEL RC-1590
(Supplied)
Figure 5: Digital Inputs and 12V Trigger Output
Entrées numériques et Branchements des sorties trigger 12 V
Digitaleingänge und 12V TRIG‑Ausgang
Entradas Digitales y Salida para Señal de Disparo de 12V
Digitale ingangen en 12V trigger‑uitgang
Collegamenti ingressi digitali e segnali Trigger 12 V
Anslutningar för digitala ingångar och 12‑volts styrsignaler
Цифровые входы и 12-В триггерный выход

8RC‑1590 Stereo Control Amplier
iPhone
Figure 6: Front USB Input
Entrée USB en face avant
Frontseitiger USB‑Eingang
Entrada USB Frontal
USB‑ingang op het voorpaneel
Ingresso USB frontale
USB‑port på fronten
USB вход на передней панели

9
English
Important Notes
When making connections be sure to:
4Turn off all the components in the system before hooking up any components, including loudspeakers.
4Turn off all components in the system before changing any of the connections to the system.
It is also recommended that you:
4Turn the volume control of the amplier all the way down before the amplier is turned on or off.
Remarques importantes
Pendant les branchements, assurez-vous que :
4Tous les maillons sont éteints avant leur branchement, quels qu’ils soient, y compris les enceintes acoustiques.
4Éteignez tous les maillons avant de modier quoi que ce soit au niveau de leurs branchements, quels qu’ils soient.
Il est également recommandé de :
4Toujours baissez le niveau sonore via le contrôle de volume, avant d’allumer ou d’éteindre l’amplicateur.
Wichtige Hinweise
Achten Sie beim Herstellen der Verbindungen auf Folgendes:
4Schalten Sie alle Komponenten im System ab, bevor Sie Geräte (einschließlich Lautsprecher) anschließen.
4Schalten Sie alle Komponenten im System ab, bevor Sie Anschlüsse im System verändern.
Ferner empfehlen wir, dass
4Sie die Lautstärke herunterdrehen, bevor Sie die Endstufe ein- oder abschalten.
Notas Importantes
Cuando realice las conexiones, asegúrese de que:
4Desactiva todos los componentes del equipo, cajas acústicas incluidas, antes de conectar cualquier nuevo componente en el mismo.
4Desactiva todos los componentes del equipo antes de cambiar cualquier conexión del mismo.
También le recomendamos que:
4Reduzca el nivel de volumen de su amplicador a cero antes de activarlo o desactivarlo.
Héél belangrijk
Bij het maken van de verbindingen:
4Zorg dat niet alleen de RC-1590, maar de gehele installatie uitstaat, als nog niet alle verbindingen gemaakt zijn.
4Zorg dat niet alleen de RC-1590, maar de gehele installatie ook uitstaat, als u verbindingen gaat wijzigen.
Wij raden u ook aan om
4de volumeregelaar van de voorversterker geheel dicht te draaien (volkomen naar links) wanneer u uw eindversterker aan- of uitzet.
Note importanti
Quando effettuate i collegamenti assicuratevi di:
4Spegnere tutti i componenti del sistema prima di collegare qualsiasi componente, inclusi i diffusori.
4Spegnere tutti i componenti del sistema prima di modicare qualsiasi connessione nel sistema.
Vi raccomandiamo inoltre di:
4Portare il volume a zero prima di accendere o spegnere l’amplicatore.
Viktigt
Tänk på följande när du gör anslutningar:
4Stäng av alla komponenter i anläggningen innan du ansluter nya komponenter, inklusive högtalare.
4Stäng av alla komponenter i anläggningen innan du ändrar någon anslutning i anläggningen.
Vi rekommenderar också föjlande::
4Vrid ner volymen på förstärkaren helt och hållet innan förstärkaren slås på eller av.
Важные замечания
Перед подсоединением:
4Выключите все компоненты, включая колонки.
4Выключите все компоненты в вашей системе, прежде чем что-то в ней менять.
Рекомендуется также:
4Вывести громкость усилителя на минимум, перед тем как включать или выключать его.

10 RC‑1590 Stereo Control Amplier
About Rotel
Our story began over 50 years ago. Over the decades, we have received
hundreds of awards for our products and satised hundreds of thousands
of people who take their entertainment seriously - like you!
Rotel was founded by a family whose passionate interest in music led them
to manufacture high-delity components of uncompromising quality. Through
the years, that passion has remained undiminished and the family goal of
providing exceptional value for audiophiles and music lovers, regardless
of their budget, is shared by all Rotel employees.
Rotel’s engineers work as a close team, listening to, and ne tuning, each
new product until it reaches their exacting musical standards. They are
free to choose components from around the world in order to make that
product the best they can. You are likely to nd capacitors from the United
Kingdom and Germany, semiconductors from Japan or the United States,
while toroidal power transformers are manufactured in Rotel’s own factory.
We all have concerns about our environment. And, as more and more
electronics are produced it is especially important for a manufacturer to do all
it can to engineer products that have a minimum impact on the environment.
At Rotel, we are proud to do our part. We have reduced the lead content
in our products by using special lead-free ROHS solder and components.
Our engineers continually strive to improve power supply efciency without
compromise to quality. When in standby mode Rotel products use minimal
power to meet global Standby Power Consumption requirements.
The Rotel factory is also doing their part to help the environment through
constant improvements to product assembly methods for a cleaner and
greener manufacturing processes.
All of us at Rotel thank you for buying this product. We are sure it will bring
you many years of enjoyment.
Getting Started
Thank you for purchasing the Rotel RC-1590 Stereo Control Amplier. When
used in a high-quality music audio system, your Rotel product will provide
years of musical enjoyment.
The RC-1590 is a full featured, high performance component. All aspects
of the design have been optimized to retain the full dynamic range and
subtle nuances of your music. The RC-1590 has a highly regulated power
supply incorporating a Rotel custom-designed toroidal power transformer
and custom-made slit foil capacitors. This low impedance power supply has
ample power reserves, which enables the RC-1590 to easily reproduce the
most demanding audio signals. This type of design is more expensive to
manufacture, but it is better for the music.
The printed circuit boards (PCB) are designed with Symmetrical Circuit Traces.
This ensures that the precise timing of the music is maintained and faithfully
recreated. The RC-1590 circuitry uses metal lm resistors and polystyrene
or polypropylene capacitors in important signal paths. All aspects of this
design have been examined to ensure the most faithful music reproduction.
The main functions of the RC-1590 are easy to install and use. If you have
experience with other stereo systems, you shouldn’t nd anything perplexing.
Simply plug in the associated components and enjoy.
Contents
Important Safety Instructions ..........................................2
Figure 1: Controls and Connections 3
Figure 2: RR‑AX100 Remote Control 4
Figure 3: Analog Input and Output Connections 5
Figure 4: Balanced (XLR) Input and Output Connections 6
Figure 5: Digital Inputs and 12V Trigger Output 7
Figure 6: Front USB Input 8
Important Notes 9
About Rotel ......................................................10
Getting Started ...................................................10
A Few Precautions 11
Placement 11
Cables 11
The RR-AX100 Remote Control........................................11
Second Amplier Remote Code 11
Remote Control Batteries 11
AC Power and Control ..............................................11
AC Power Input s11
POWER Switch and Power Indicator 111
12V TRIGGER Connection t12
Input Signal Connections ............................................12
Phono Input iand Ground Connection (GND) u12
Line Level Inputs io 12
Balanced (XLR) Inputs \12
Digital Inputs -12
Output Connections ................................................12
Digital output =12
Line Output p12
MONO SUB Output [12
Preamp Output ]12
Balanced (XLR) Preamp Output a12
Headphone Output 5..............................................12
Remote Sensor 2................................................13
Display 3......................................................13
Front USB Input 6................................................13
APTX Bluetooth Connection 0........................................13
Audio Controls ...................................................13
Volume Control 4DE 13
Balance Control 9C13
Tone Control Bypass 9C13
Bass and Treble Controls 9C13
Function Control 8L13
Dimmer Control ...................................................13
Display Dimmer 9B13
Rotel Link e....................................................14
EXT REM IN Jack t...............................................14
RS232 y. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PC-USB Input w..................................................14
Network Connection q.............................................14
Setup Menu ......................................................14
Troubleshooting ...................................................16
Power Indicator Is Not Illuminated 16
Fuse Replacement 16
No Sound 16
Playable Audio Format 16
Specications ....................................................16

11
English
A Few Precautions
WARNING: To avoid potential damage to your system, turn off ALL
the components in the system when connecting or disconnecting the
loudspeakers or any associated components. Do not turn the system
components back on until you are sure all the connections are correct
and secure. Pay particular attention to the speaker wires. There must
be no loose strands that could contact the other speaker wires, or the
chassis of the amplier.
Please read this manual carefully. In addition to basic installation and
operating instructions, it provides valuable information on various RC-1590
system congurations as well as general information that will help you get
optimum performance from your system. Please contact your authorized
Rotel dealer for answers to any questions you might have. In addition, all
of us at Rotel welcome your questions and comments.
Save the RC-1590 shipping carton and all enclosed packing material for
future use. Shipping or moving the RC-1590 in anything other than the
original packing material may result in severe damage to your amplier.
If included in the box please ll out and send in the owner’s registration
card. Also be sure to keep the original sales receipt. It is your best record
of the date of purchase, which you will need in the event warranty service
is ever required.
Placement
Like all audio components that handle low-level signals, the RC-1590 can
be affected by its environment. Avoid placing the RC-1590 on top of other
components. Also avoid routing audio signal cables near power cords. This
will minimize the chance it will pick up hum or interference.
The RC-1590 is supplied with an RR-AX100 remote control and must be
placed where the infrared signal from the remote can reach the front panel
Remote Sensor.
Cables
Be sure to keep the power cords, digital signal cables and regular audio
signal cables in your installation away from each other. This will minimize
the chance of the regular audio signal cables picking up noise or interference
from the power cords or digital cables. Using only high quality, shielded
cables will also help to prevent noise or interference from degrading the
sound quality of your system. If you have any questions see your authorized
Rotel dealer for advice about the best cable to use with your system.
The RR‑AX100 Remote Control
Some functions can be done with either the front panel controls, or the
supplied RR-AX100 remote control. When these operations are described,
the square call out numbers refer to the main unit, while the encircled letters
refer to the remote control.
Second Amplifier Remote Code
The factory setting is remote code 1. If you nd that the remote is conicting
with other Rotel ampliers, you can change to remote code 2 with the
following steps.
1. From the remote control press Tuner Land 2 Mat the same time to set
the remote control to send Audio Code 2.
2. Point the remote at the unit and press 2 Mkey for 8 seconds. The unit
will show “Audio Custom Code 1 -> 2”.
3. Repeat the above procedure and press “1” key instead of “2” to change
the unit back to Code 1.
NOTE: The remote control can be used to operate the basic functions of
Rotel tuners and CD players. Remote control buttons labeled IKMN
can be used to operate CD or Tuner functions in your system. For the
remote control to operate properly, make sure both the remote control
and the CD or Tuner are both in same remote code. For more information
please contact your authorized Rotel dealer.
Remote Control Batteries
Two AA size batteries (supplied) must be installed before the remote control
can be used. To install the batteries, remove the cover on the back of the
RR-AX100. Install the batteries as shown in the illustration in the battery
well. Test the control for proper operation, then replace the cover. When
the batteries become weak the remote control won’t operate the RC-1590
consistently. Installing fresh batteries should eliminate the problem.
AC Power and Control
AC Power Input s
Your RC-1590 is congured at the factory for the proper AC line voltage in
the country where you purchased it (either 120 volts AC or 230 volts AC
with a line frequency of either 50 Hz or 60 Hz). The AC line conguration
is noted on a decal on the back panel.
NOTE: Should you move your unit to another country, it may be possible
to recongure it for use on a different line voltage. Do not attempt to
perform this conversion yourself. Opening the enclosure of the unit
exposes you to dangerous voltages. Consult a qualied service person
or the Rotel factory service department for information.
NOTE: Some products are intended for sale in more than one country
and as such are supplied with more than one AC cord. Please only use
the one appropriate for your country/region.
The RC-1590 should be plugged directly into a 2-pin polarized wall outlet.
Do not use an extension cord. A heavy duty multi-tap power outlet strip may
be used if it (and the wall outlet) is rated to handle the current demanded
by the RC-1590 and all the other components connected to it.
If you are going to be away from home for an extended period of time
such as a month long vacation, it is a sensible precaution to unplug the RC-
1590 (as well as other audio and video components) while you are away.
POWER Switch and Power Indicator 1
Press the front panel Power Switch button to turn the unit on. The Power
Indicator light is illuminated when the unit is on. Press the Power Switch
button again to turn the unit off.
When the power switch is in the ON position, the remote control ON and
OFF buttons may be used to activate the RC-1590. In Standby mode the
power LED remains illuminated, but the display is turned OFF.
NOTE: Place the self adhesive ring over the light surrounding the power
switch if the blue light is too bright.

12 RC‑1590 Stereo Control Amplier
12V TRIGGER Connection t
Some audio components can be turned on automatically when they receive a
12V turn on “signal”. The two12V Trigger Outputs on the RC-1590 provide
the required signal. Connect compatible components to the RC-1590 with
a conventional 3.5mm mini mono plug cable. When the RC-1590 is in
standby mode, the trigger signal is disabled, so the components controlled
by it will be turned off.
NOTE: Do not connect both the Rotel Link and 12V trigger cables at
the same time. The 12V trigger’s power on or off features will override
the Rotel Link features.
Input Signal Connections
See Figure 3
NOTE: To prevent loud noises that neither you nor your speakers will
appreciate, make sure the system is turned off when you make any
signal connections.
Phono Input iand Ground Connection (GND) u
See Figure 3
Plug the cable from the turntable into the appropriate left and right phono
inputs. If the turntable has a “ground” wire, connect it to the screw terminal
to the left of the Phono inputs. This will help prevent hum and noise.
Line Level Inputs io
See Figure 3
The CD, Tuner, and Aux inputs of the amplier are analog “line level” inputs.
These inputs are for connecting components such as CD players or other
audio playback devices with an analog audio output.
The left and right channels are clearly labeled and should be connected to
the corresponding channels of the source component. The Left connectors
are white, the Right connectors are red. Use high quality RCA cables for
connecting input source components to the RC-1590. Ask your authorized
Rotel dealer for advice about cables.
Balanced (XLR) Inputs \
See Figure 4
A pair of balanced XLR inputs accept audio signals from CD player, Blu-ray
player or other source components with XLR outputs.
NOTE: You should choose only one method of analog connection from
a source component to RC-1590. Do not connect both the RCA and
XLR outputs of a source component to the RC-1590 at the same time.
Digital Inputs -
See Figure 5
There are three sets of digital inputs labeled 1, 2 and 3, for COAXIAL and
OPTICAL respectively. Connect the COAXIAL or OPTICAL PCM outputs of
your source component into these sockets. The digital signals will be decoded
and played by the RC-1590. The unit is capable of decoding PCM signals
up to 24 bit, 192kHz.
Output Connections
Digital output =
If you are using an outboard D/A converter or other digital processor, you
will need an unprocessed digital data stream from the RC-1590. Using a
standard 75 ohm coax/optical digital cable, connect the RC-1590’s digital
output to the digital input connector on the outboard D/A converter.
Line Output p
The line output connectors can be used to send the analog audio to a separate
processor device. These outputs bypass the volume encoder and are full line
level output. They should be connected to the analog inputs of the processor.
As with other sources be sure to connect the Left and Right channels of each
device to the proper channels on the associated components. Use high
quality connecting cables to prevent loss of sound quality.
MONO SUB Output [
There are 2 connectors for mono subwoofer output to connect to a subwoofer.
These mono outputs are summed with both the left and right audio signal.
They are parallel outputs allowing 2 subwoofers to be connected to the
RC-1590.
Preamp Output ]
See Figure 3
The RC-1590 RCA-type output connectors are compatible with most power
ampliers. As always, select high quality audio interconnect cables. Connect
the left and right channel outputs of the RC-1590 to the corresponding inputs
on the amplier or other component.
NOTE: There are two sets of RCA outputs on the RC-1590. The second
set of outputs may be used in custom system congurations to drive
a second power amplier or to supply a signal to a special signal
processor.
Balanced (XLR) Preamp Output a
See Figure 4
Two pairs of XLR balanced connectors supply an analog output signal from
the RC-1590 to a power amplier with XLR balanced input connectors.
NOTE: Do not connect both the RCA and XLR to the same amplier
at the same time.
Headphone Output 5
The headphone output allows you to connect headphones for private listening.
This output accepts a standard 3.5mm (1/8”) mini stereo headphone
connector. Plugging in a set of headphones does not cut off the signal to the
preamp outputs. In most instances you should turn off the power amplier
when listening to headphones.

13
English
NOTE: Because the sensitivity of speakers and headphones can
vary widely, always reduce the volume level before connecting or
disconnecting headphones.
Remote Sensor 2
This remote sensor window receives IR commands from the remote control.
Please do not block this sensor.
Display 3
The front panel display shows the source selected, volume level and tone
settings. The display can be dimmed using the RC-1590 setup menu or the IR
remote controller. See the Dimmer Control section of this manual for details.
Front USB Input 6
See Figure 6
The front USB input can be connected to an iPod or iPhone. With iPod or
iPhones, simply plug the device into the front USB and select USB function
from the source selector. The iPod and iPhone remain active allowing search
and play functions.
APTX Bluetooth Connection 0
The Bluetooth Antenna 0on the RC-1590’s back panel is for wireless
streaming via Bluetooth, from your device (i.e. mobile phones). From your
mobile device, look for “Rotel Bluetooth” and connect to it. Connection is
normally automatic, but if prompted for a password, please press “0000”
on your device. The RC-1590’s supports both traditional Bluetooth and APTX
Bluetooth audio streaming.
Audio Controls
Volume Control 4DE
Turn the knob clockwise to increase the volume, or counter clockwise to
decrease the volume. From the remote control press the volume + or - D
button to turn the volume up or down. Press the MUTE Ebutton to completely
mute the volume.
Balance Control 9C
The Balance Control adjusts the left-to-right balance of the sound output. The
factory default is the center position or “0”. To change the balance from
the front panel, press the MENU 9button to toggle the front display to
BALANCE SETTING mode. Then press the - or + buttons on the front panel to
change the value to LEFT or RIGHT. The value can change from L15 to R15.
NOTE: This setting is saved permanently including after powering off
the RC-1590.
To make temporary changes not saved after power off, from the remote
control press the BAL Cbutton to access the BALANCE setting, then press
the left/right Garrow buttons to adjust. When nished, press the ENTER
Gbutton to exit the menu.
Tone Control Bypass 9C
Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. The front display will show TONE
BYPASS. To turn on the tone control from the front panel, press the MENU
9button to toggle to the Bypass control then press the - or + buttons on
the front panel to turn bypass on or off.
NOTE: This setting is saved permanently including after powering off
the RC-1590.
To temporarily change the Tone Control Bypass, press the TONE 7button
on the front panel, then press the - or + button on the front panel to turn
the Bypass on or off, or press the BYPASS Cbutton on the remote control.
Bass and Treble Controls 9C
Set the Bass or Treble controls from the front panel by pressing the MENU
9button to toggle to either the Bass or Treble Setting menu. Then press
the - or + button on the front panel to adjust the value. The Bass and Treble
values range from -10 to +10.
NOTE: These settings are saved permanently including after powering
off the RC-1590.
To temporarily change the Bass and Treble settings, press the TONE 7
button on the front panel to toggle to the Bass or Treble Setting, then press
the - or + button on the front panel to adjust the value. Or from the remote
control, press the BASS or TREBLE Cbutton, then press the left/right G
arrow buttons on the remote control.
NOTE: When Tone Bybass is disabled, Bass and Treble settings can
not be changed by the Tone button 7or the BASS/TREBLE buttons C.
A properly setup high-performance audio system produces the most natural
sound with little or no adjustment of the tone controls. Use these controls
sparingly. Be particularly careful when turning the controls up as this
increases the power output in the bass or treble range, increasing the load
on the amplier and speakers.
NOTE: Setting the Bass and Treble controls do not automatically turn
on the tone control. To turn on tone control, refer to previous section
Tone Control Bypass.
NOTE: Tone Bypass, Bass, Treble and Balance settings are only saved
permanently from within the Menu. Adjustments made using the 7C
buttons are temporary only and not saved after power off.
Function Control 8L
The Function control selects the input signal source. From the front panel
or remote control press the corresponding input button to select the source
to listen to.
Dimmer Control
Display Dimmer 9B
To change the brightness of the front display, press the MENU 9button
to toggle to the Display Settings. Then press the - or + buttons on the front
panel to change the display brightness.
NOTE: This setting is saved permanently including after powering off
the RC-1590.

14 RC‑1590 Stereo Control Amplier
To temporarily change the display brightness, press the DIM Bbutton on
the remote control.
NOTE: Display Dimmer setting is only saved permanently from within
the Menu. Adjustment made using the Bbutton is temporary only and
not saved after power off.
Rotel Link e
The ROTEL LINK OUT connection can be made with the stereo 3.5 mm
cable (supplied) to a Rotel integrated amplier and CD player. While the
ROTEL LINK IN can optionally attach to Rotel network enabled products
with ROTEL LINK OUT connections.
These allow the attached Rotel products to communicate with each other
and be controlled via the Rotel Remote App (available for download on
the iTunes®store).
NOTE: Only the Rotel Link cables supplied with this product should be
used. These 3.5 mm cables have WHITE connector ends and should
not be confused with the 12 Volt Trigger cables that have BLACK
connector ends.
EXT REM IN Jack t
This 3.5mm mini-jack receives command codes from industry-standard infrared
receivers via hard-wired connections. This feature could prove useful when
the unit is installed in a cabinet and the front-panel sensor is blocked. Consult
your authorized Rotel dealer for information on these external repeaters and
the proper wiring of a jack to t the mini-jack receptacle.
RS232 y
The RC-1590 can be controlled via RS232 for integration with automation
systems. The RS232 input accepts a standard straight DB-9 Male-to-Female
cable.
For additional information on the connections, software, and operating codes
for computer control of the RC-1590, contact your authorized Rotel dealer.
PC‑USB Input w
See Figure 5
Connect this input using the supplied USB cable to the PC-USB socket of
your computer.
The RC-1590 supports both USB Audio Class 1.0 and USB Audio Class
2.0 modes. Windows computers do not require installation of a driver for
USB Audio Class 1.0 and support playback of audio up to 96kHz sampling
rates. The Factory Default setting is USB Audio Class 1.0.
To take advantage of USB Audio Class 2.0 audio playback supporting
up to 192kHz sampling rates you will need to install the Windows driver
supplied on CD included with the RC-1590. You will also need to switch
the RC-1590 to USB Audio Class 2.0 playback mode with the following:
• Press MENU on the front panel until “PC-USB AUDIO CLASS” appears
on the display.
• Select “2.0” using the “-” button then press “ENTER”.
• Power cycle the RC-1590 and reboot your PC after changing the USB
Audio mode to ensure both units are properly congured.
Many audio playback applications do not support 192kHz sampling rate.
Please conrm your audio player supports 192kHz audio and you have
192kHz audio les to properly playback this sample rate. Also, you may
need to congure the audio driver in your PC to output 192kHz or your
computer may “down sample” to a lower audio sample rate. For more
information please refer to your audio player or operating system information.
NOTE: USB Audio Class 2.0 requires installation of the Windows PC
driver on the CD ROM included with the RC-1590.
NOTE: MAC computers do not require a driver to support PC-USB
1.0 or 2.0 audio.
NOTE: Upon successful installation of the driver, you may need to select
the ROTEL audio driver from the audio/speaker setup of your computer.
NOTE: The RC-1590 supports both DSD and DOP audio playback
in 1X and 2X formats. Consult your audio player to conrm proper
operation for playback of these audio formats.
Network Connection q
The RC-1590 can be attached to a network using the rear panel NETWORK
socket. The NETWORK congurations allow both static and DHCP IP
addressing. See the Network Setup section of this manual under Setup
Menu for IP address conguration information.
The NETWORK connections allows software updates to be downloaded from
the Internet. The Network connection also allows IP control for integration
with automation systems.
For additional information on the IP connection please contact your
authorized Rotel dealer.
Setup Menu
You can access the settings menu from the front panel by pressing the MENU
9button or the SETUP Fbutton on the remote control. You can change
the value of the selected option by pressing the +/- button on the front panel
or the left/right Garrow buttons on the remote control. Step through the
sub-menus by pressing the MENU 9button on the front panel or SETUP
Fbutton on the remote control.
• TONE Control: TONE BYPASS ON/OFF, BASS level and TREBLE levels
can be changed to desired settings. Press the ENTER button on the front
panel or on the remote control to toggle between the tone setup options.
(For more information on Tone Control refer to the Tone Control Bypass,
Bass and Treble control sections.)
NOTE: These settings are stored permanently even after the RC-1590
is powered off.

15
English
• PC-USB AUDIO CLASS: Changes supported PC-USB Audio Class of the
attached device.
NOTE: Some computers attached to the PC-USB do not support USB
Audio Class 2.0 and do not support 24/192 audio playback. If needed
the PC-USB can be congured for USB Audio Class 1.0. Please consult
your computer operating system for details.
• NETWORK: Shows the network connection status and to view/congure
the network settings. If the network is properly congured and attached
“Connected” will be displayed. To view or modify the network settings
press the ENTER button.
The RC-1590 supports both DHCP and STATIC IP addressing. Select the
desired IP address method and press ENTER.
If DHCP is selected you can refresh IP address by pressing ENTER or press
MENU to view IP address information. Press the MENU button to toggle
through IP address settings. If the IP address is renewed the network will
be tested and connection status reported.
If STATIC IP address mode is selected you must congure all settings for the
network including IP Address, Subnet Mask, Gateway and DNS Server. Use
the left/right or +/- buttons to adjust the values and press ENTER to move to
the next value. When the proper IP information is congured press MENU
to go to the next setting. After entering the STATIC IP address information
the network will be tested and connection status reported.
NOTE: For more information regarding network connection please
contact your authorized Rotel dealer.
NOTE: A network connection is not required for the RC-1590 to
operate.
• MAIN: This shows the current software version loaded into the RC-1590.
The software can be updated if the RC-1590 is properly connected to the
Internet.
• Press ENTER to check if a new software version is available.
• If a new software version is available press the + button on the front
panel or the right button on the remote control to select YES then press
ENTER button to begin the software update process.
• The new software will be downloaded from the Internet. The RC-1590
will power cycle when the software update is complete.
NOTE: Do NOT power off the RC-1590 during the software update
process.
NOTE: It is recommended to Reset Factory Defaults after the software
update is complete.
• PC-USB: This shows current loaded software version for PC-USB processor.
• FACTORY DEFAULT: This sets the unit back to the original state as when
it left the factory. Press the + button on the front panel or the Right button
on the remote control to select <YES> then press the ENTER button on the
front panel or on the remote control.
• BALANCE: Changes left/right balance. (For more information on Balance
sections.)
NOTE: This setting is stored permanently even after the RC-1590 is
powered off.
• DIMMER: Dims the display.
NOTE: This setting is stored permanently even after the RC-1590 is
powered off.
• ROTEL LINK RCD: Selects how the CD player is connected to the amplier,
either CD (analog), COAX1, COAX2 and BAL-XLR. CD is the factory default.
• POWER ON MAX VOLUME: This sets the maximum volume level when
the unit is turned ON. “45” is the factory default.
NOTE: Power On Max Volume settings do not apply to sources
congured with Fixed Gain.
• POWER OPTION: Enables the RC-1590 to be controlled via the network
port when attached to an automation system. The power consumption is
higher in Quick Power mode. If network control is not required select the
Normal Power mode. “Normal” is the factory default.
• AUTO POWER OFF: The RC-1590 can be congured to automatically
power off if unused for a specied period. If no changes are made to the
unit within the specied “Auto Power Off” timer the unit will automatically
go to STANDBY mode. The Auto Power Off timer will be restarted if changes
are made to the volume, source or playback. The default for Auto Power
Off is set to DISABLE.
Valid settings include: DISABLE, 1 HOUR, 2 HOURS, 5 HOURS, 12 HOURS.
• FIXED GAIN: Congures a Fixed Volume level for a specied input. To
enable this feature press the +/- buttons on the front panel to select the
desired xed volume level for Aux, FUSB, PC-USB, Coax 1, Coax 2, Optical
1, Optical 2 or Bluetooth. When enabled and the input with a Fixed Volume
is selected, the Volume level will immediately be set to the specied level.
Valid settings include: VARIABLE, FIXED 01-95, FIXED MAX.
• AUX VOL: VARIABLE (disabled) is factory default.
• FUSB VOL: VARIABLE (disabled) is factory default.
• PC-USB VOL: VARIABLE (disabled) is factory default.
• OPT1 VOL: VARIABLE (disabled) is factory default.
• OPT2 VOL: VARIABLE (disabled) is factory default.
• COAX1 VOL: VARIABLE (disabled) is factory default.
• COAX2 VOL: VARIABLE (disabled) is factory default.
• BLUETOOTH VOL: VARIABLE (disabled) is factory default.
NOTE: The Volume knob on the front panel and Volume +/- buttons
on the IR remote are disabled when the volume is Fixed. To disable this
feature set the Fixed Volume level to “Variable”.

16 RC‑1590 Stereo Control Amplier
Specications
Total Harmonic Distortion (20 Hz - 20k Hz) < 0.002%
Input Sensitivity / Impedance
Phono Input (MM) 2.5 mV / 47k ohms
Line Level Inputs (RCA) 150 mV / 100k ohms
Line Level Inputs (XLR) 250 mV / 100k ohms
Output Level
Line Level (RCA) 1 V
Balanced (XLR) 2 V
Frequency Response:
Phono Input 20 Hz - 20k Hz, 0 ± 0.2 dB
Line Level Inputs 10 Hz - 100k Hz, 0 ± 0.1 dB
Signal to Noise Ratio (A weighting)
Phono Input 80 dB
Line Level Inputs 112 dB
Channel Separation
Phono Input > 75 dB
Line Level Inputs > 75 dB
Digital Section
Frequency Response 20Hz - 20kHz (±0.5 dB, Max)
Signal to Noise Ratio (A weighting) 108 dB
Digital Inputs SPDIF LPCM
(up to 192kHz 24 bit)
PC-USB USB Audio Class 1.0
(up to 96kHz 24 bit)
USB Audio Class 2.0
(up to 192kHz 24bit)*
*Driver installation required
General
Power Requirements:
USA: 120 Volts, 60 Hz
EC: 230 Volts, 50 Hz
Power Consumption 45 watts
Standby Power Consumption < 0.5 watts
BTU 78 BTU/h
Dimensions (W x H x D) 431 x 144 x 348 mm
(17 x 5 11/16 x 13 7/9ins)
Front Panel Height 3U (132.6 mm, 5 1/4ins)
Weight (net) 9.2 kg, 20.28 lbs.
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel and the Rotel Hi-Fi logo are registered trademarks of The Rotel Co., Ltd, Tokyo,
Japan.
NOTE: All previously congured options will be erased and reset to
the factory default settings.
Troubleshooting
Most difculties in audio systems are the result of incorrect connections,
or improper control settings. If you encounter problems, isolate the area
of the difculty, check the control settings, determine the cause of the fault
and make the necessary changes. If you are unable to get sound from the
RC-1590, refer to the suggestions for the following conditions:
Power Indicator Is Not Illuminated
The Power Indicator ring around the power button and the basic items in the
Display window should be illuminated whenever the RC-1590 is plugged
into the wall power outlet and the POWER switch is pushed in. If it does not
light, test the power outlet with another electrical device, such as a lamp.
Be sure the power outlet being used is not controlled by a switch that has
been turned off.
Fuse Replacement
If another electrical device works when plugged into the power outlet, but
the Power Indicator still will not light when the RC-1590 is plugged into
the wall outlet, it indicates that the internal power fuse may have blown.
If you believe this has happened, contact your authorized Rotel dealer to
get the fuse replaced.
No Sound
Check the signal source to see if it is functioning properly. Make sure the
cables from the signal source to the RC-1590 inputs are connected properly.
Check all the wiring between the RC-1590 and the power amplier, and
the speakers.
Playable Audio Format
USB Apple (iPhone, iPod, iPad)
Format Notes
Any supported le
loaded to Apple
device.
Any supported le loaded to Apple device. Phone
may resample depending on stored format. May
exclude Apps designed to play formats not originally
supported by the sending device.
APTX Bluetooth
Format Notes
Any format supported
by the sending device.
May exclude Apps designed to play formats not originally
supported by the sending device.
PC-USB
Format Notes
Format determined
by the Media Player/
Server software that
you use.
Any supported format by the PC software
PCM Audio: 44.1k, 48k, 88.2k, 96k, 176.4k, 192k
(16 bit and 24 bit)
DSD64 and DSD128
Coax/Optical
Format Notes
SPDIF LPCM 44.1k, 48k, 88.2k, 96k, 176.4k, 192k
16 bit, 24 bit

17
English
“Made for iPod,” and “Made for iPhone,” means that an electronic accessory
has been designed to connect specically to iPod or iPhone, respectively, and
has been certied by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with
safety and regulatory standards. Please note that the use of this accessory
with iPod, or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other countries.

18 RC‑1590 Amplicateur de Contrôle Stéréo
Remarque
Le branchement repéré RS232 ne concerne que des techniciens agréés
uniquement.
ATTENTION : Il n’y a àl’intérieur aucunepièce susceptible d’êtremodifiée
par l’utilisateur. Adressez‑vous impérativementà une personne qualifiée.
ATTENTION : Pour réduire tout risque d’électrisation ou d’incendie,
ne pas exposer l’appareil à une source humide, ou à tout type de risque
d’éclaboussure ou derenversement de liquide. Nepas poser dessus d’objet
contenant un liquide, comme un verre, un vase, etc. Prenez garde à ce
qu’aucun objet ou liquide ne tombe à l’intérieur de l’RC‑1590 par ses
orifices de ventilation. Si l’appareil est exposé à l’humidité ou si un objet
tombe à l’intérieur, débranchez‑le immédiatement de son alimentation
secteur, et adressez‑vous immédiatement et uniquement à une personne
qualifiée et agréée.
Tous les conseils de sécurité et d’installation doivent être lus avant de
faire fonctionner l’appareil.
Conservez soigneusement ce livret pour le consulter à nouveau pour
de futures références.
Tous les conseils de sécurité doivent être soigneusement respectés.
Suivez les instructions. Respectez les procédures d’installation et de
fonctionnement indiquées dans ce manuel.
L’appareil doit être nettoyéuniquement avecun chiffonsec ouun aspirateur.
Ne pas utiliser cet appareil près d’un point d’eau.
Il ne doit pas être posé sur un fauteuil, un canapé, une couverture ou
toute autre surface susceptible de boucher ses ouïes d’aération ; ou
placé dans un meuble empêchant la bonne circulation d’air autour des
orifices d’aération.
Cet appareil doit être placé loin de toute source de chaleur, tels que
radiateurs, chaudières, bouches de chaleur ou d’autres appareils
produisant de la chaleur.
Tous les appareils Rotel sontconçus en totaleconformité
avec les directives internationales concernant les
restrictions d’utilisation de substances dangereuses
(RoHS) pour l’environnement, dans les équipements
électriques et électroniques, ainsique pour le recyclage
des matériaux utilisés (WEEE, pour Waste Electrical
and Electronic Equipment). Le symbole du conteneur
à ordures barré par une croix indique la compatibilité
avec ces directives, et le fait que les appareils peuvent
être correctement recyclés ou traités dans le respect
total de ces normes.
Ce symbole signifie que cet appareil bénéficie d’une
double isolation électrique. Le branchement d’une
mise à la masse ou à la terre n’est pas nécessaire.
Remarques importantes concernant la sécurité
ATTENTION : La prise d’alimentation située à l’arrière constitue le
principal moyen pour déconnecter l’appareil du secteur. Cet équipement
doit être positionné dans un espace ouvert qui permet de garder l‘accès
au câble d’alimentation.
Cet appareil doit être branché sur une prise d’alimentation secteur,
d’une tension et d’un type conformes à ceux qui sont indiqués sur la
face arrière de l’appareil (USA : 120 V/60 Hz, CE : 230 V/50 Hz).
Brancher l’appareil uniquement grâce au cordon secteur fourni, ou à
un modèle équivalent. Ne pas tenter de modifier ou changer la prise.
Notamment, ne pas tenter de supprimer la prise de terre (troisième
broche de la prise) si celle‑ci est présente. Si la prise n’est pas conforme
à celles utilisées dansvotre installation électrique, consultezun électricien
agréé. Ne pas utiliser de cordon rallonge.
La prise d’alimentationsecteur constitue lemoyen radical de déconnexion
de l’appareil. Elle doit donc rester en permanence accessible, car sa
déconnexion constituela seule assuranceque l’appareil n’estplus alimenté
par le secteur. La diode LED de mise en veille Standby ne s’allume plus
lorsque le cordon d’alimentation est débranché.
Prendre garde à ce que ce cordon d’alimentation ne soit pas pincé,
écrasé ou détérioré sur tout son trajet, et à ce qu’il ne soit pas mis en
contact avec une source de chaleur. Vérifiez soigneusement la bonne
qualité des contacts, àl’arrière de l’appareil comme dansla prise murale.
Débranchez le câble d’alimentation en cas d’orage, ou si l’appareil ne
doit pas être utilisé pendant une longue période.
N’utilisez que des accessoires préconisés par le constructeur.
N’utilisez que des meubles, supports, systèmes de
transport recommandés par Rotel. Procédez toujours
avec la plus extrême précaution lorsque vous déplacez
l’appareil, afin d’éviter tout risque de blessure.
L’appareil doit être immédiatement éteint, débranché puis retourné au
service après‑vente agréé dans les cas suivants :
•Le câble d’alimentation secteur ou sa prise est endommagé.
•Un objet esttombé, ou du liquidea coulé à l’intérieurde l’appareil.
•L’appareil a été exposé à la pluie.
•L’appareil ne fonctionne manifestement pas normalement.
•L’appareil est tombé, ou le coffret est endommagé.
Les piles de la télécommande infra‑rouge ne doivent en aucun cas
exposéesà une chaleurexcessive notammentau feuouau soleildirect.
12
3
Assignation des connecteurs
Audio Symétrique (prise XLR 3 broches) :
Pin 1 : Masse/Terre
Pin 2 : Phase/+ve /Point chaud
Pin 3 : Hors Phase /‑ve / Point froid
L’éclair dans un triangle équilatéral indique
la présence interne de tensions électriques
élevées susceptibles de présenter des
risques graves d’électrocution.
Le point d’exclamation dans un triangle
équilatéral indique à l’utilisateur la
présence de conseils et d’informations
importantes dans le manuel d’utilisation
accompagnant l’appareil. Leur lecture est
impérative.

19
Français
A propos de Rotel
Notre histoire commence il y a environ 50 ans. Depuis, au l des années,
nous avons reçu des centaines de prix et de récompenses, et satisfait des
centaines de milliers de personnes – comme vous !
Rotel a été fondée par une famille passionnée de musique, qui a décidé
de fabriquer des maillons Haute Fidélité sans compromis aucun. Depuis sa
création, cette passion est restée intacte, et cette famille s’est xée comme
objectif de proposer à tous les audiophiles et mélomanes les meilleurs
appareils possibles, quel que soit leur budget. Une volonté partagée par
tous les employés de Rotel.
Les ingénieurs Rotel travaillent comme une équipe très soudée, écoutant,
peaunant chaque nouveau modèle jusqu’à ce qu’il atteigne exactement
leurs standards – très élevés – de musicalité. Ils sont libres de choisir des
composants en provenance du monde entier, an de concevoir le meilleur
produit possible. C’est ainsi que vous trouverez dans nos appareils des
condensateurs d’origine britannique ou allemande, des transistors japonais
ou américains, tandis que les transformateurs toriques sont toujours fabriqués
dans nos propres usines Rotel.
Nous sommes tous concernés par la qualité de l’environnement. Et, comme de
plus en plus de produits électroniques sont fabriqués puis éliminés quelques
années plus tard, il est désormais essentiel qu’un constructeur fabrique tous
ses produits en veillant à ce qu’ils aient un impact minimum sur la Terre et
les nappes phréatiques.
Chez Rotel, nous sommes très ers d’apporter notre pierre à ce nouvel
édice. Nous avons réduit la teneur en plomb de nos électroniques, en
utilisant notamment une soudure spéciale ROHS, tandis que notre nouvelle
gamme d’amplicateurs fonctionnant en classe D (non numérique) présente
un rendement cinq fois supérieur aux générations conventionnelles
précédentes, délivrant pourtant encore plus de puissance, avec une qualité
encore supérieure. Ces appareils ne chauffent pas, dépensent beaucoup
moins d’énergie, sont donc très bons pour l’environnement tout en étant
encore plus musicaux.
En plus, nous imprimons tous nos catalogues et manuels sur papier recyclé.
Ce ne sont certes que de petites étapes. Mais ne sont-ce pas justement les
plus importantes ? Nous continuons activement la recherche et la mise au
point de nouvelles méthodes, et l’utilisation de nouveaux matériaux pour
aboutir à un processus de fabrication général plus écologique et plus propre.
Tous les membres de l’équipe Rotel vous remercient pour l’achat de cet
appareil. Nous sommes persuadés qu’il vous offrira de nombreuses années
d’intense plaisir musical.
Mise en route
Merci d’avoir acheté cet Amplicateur de Contrôle Stéréo Rotel RC-1590.
Associé à un ensemble audio de qualité, il vous offrira de nombreuses
années de plaisir musical.
Le RC-1590 est un appareil haute performance, doté de fonctionnalités
avancées. Tous les aspects de sa conception ont été optimisés pour garantir
une dynamique sans faille et restituer les nuances les plus subtiles de votre
musique. Le RC-1590 dispose d’une alimentation hautement régulée intégrant
un transformateur de puissance toroïdal spéciquement conçu par Rotel. Cette
Sommaire
Figure 1 : Commandes et Branchements 3
Figure 2 : Télécommande infrarouge RR‑AX100 4
Figure 3 : Branchements des entrées et sorties analogiques 5
Figure 4 : Branchements des entrées et sorties symétriques (XLR) 6
Figure 5 : Entrées numériques et Branchements des sorties trigger 12 V 7
Figure 6 : Entrée USB en face avant 8
Remarques importantes 9
Remarques importantes concernant la sécurité ............................18
A propos de Rotel .................................................19
Mise en route ....................................................19
Quelques précautions préalables 20
Installation 20
Câbles 20
Télécommande infrarouge RR-AX100....................................20
Code de télécommande pour un second amplicateur 20
Piles de la télécommande 20
Alimentation secteur et commandes.....................................20
Prise secteur s20
Interrupteur de mise sous tension/veille Standby et indicateurPower121
Branchement trigger 12 V t21
Connexions d’entrée du signal ........................................21
Entrée Phono iet connexion à la masse [GND] u21
Entrées Lignes io 21
Entrées symétriques (XLR) \21
Entrées Numériques -21
Connexion des sorties ..............................................22
Sortie Numérique =22
Sorties Ligne p22
Sortie SUB MONO [22
Sorties Préampli ]22
Sorties Préampli symétriques (XLR) a22
Sortie Casque 5.................................................22
Récepteur de la télécommande 2.....................................22
Afcheur 3.....................................................22
Entrée USB face avant 6...........................................22
Connexion Bluetooth APTX 0........................................22
Commandes Audio .................................................22
Contrôle de volume 4DE 22
Balance 9C22
Activation/désactivation du contrôle de tonalité 9C23
Ajustements Graves/Aigus 9C23
Commutateur de fonction 8L23
Contrôle de luminosité ..............................................23
Luminosité de l’écran 9B23
ROTEL LINK e...................................................23
Prise jack pour télécommande externe (EXTREM IN) t.....................23
RS232 y. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Entrée pour PC-USB w.............................................24
Connexion réseau q...............................................24
Menu de conguration ..............................................24
Problèmes de fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
L’indicateur de mise sous tension n’est pas allumé 26
Remplacement du fusible 26
Pas de son 26
Formats de lecture compatibles 26
Spécications.....................................................26

20 RC‑1590 Amplicateur de Contrôle Stéréo
alimentation basse impédance dispose de réserves d’énergie importantes
et permet au RC-1590 de prendre facilement en charge tous les types de
signaux audio, même les plus exigeants. Ce type de composant est certes
plus cher à fabriquer, mais il est d’une qualité supérieure sur le plan musical.
Les cartes électroniques (PCB) sont conçues sur le principe de circuits
symétriques (Symmetrical Circuit Traces), pour garantir une synchronisation
parfaite du signal musical, et donc une restitution optimale. Les circuits
utilisent des résistances à ls métalliques et des condensateurs polystyrènes
ou polypropylènes sur les circuits les plus critiques. Tous les aspects de la
conception de l’appareil ont été rigoureusement étudiés pour garantir une
reproduction musicale la plus dèle possible.
Toutes les fonctions principales du RC-1590 sont faciles à congurer et à
utiliser. Si vous avez déjà l’expérience d’autres systèmes stéréo, vous ne
devriez pas rencontrer de difcultés particulières. Connectez simplement
les composants associés, et protez de votre musique.
Quelques précautions préalables
AVERTISSEMENT : Pour éviter d’endommager potentiellement votre
système, veillez à bien mettre hors tension TOUS les éléments lorsque
vous branchez ou vous débranchez les enceintes acoustiques et les
composants associés. Ne mettez pas les appareils en marche tant vous
n’êtes pas certain que tous les branchements sont corrects et sécurisés.
Prêtez une attention particulière aux câbles des enceintes acoustiques.
Il ne doit y avoir aucun l qui puisse entrer en contact avec les autres
câbles d’enceintes ou avec le châssis de l’amplicateur.
Merci de lire soigneusement ce manuel. Il vous donne des renseignements
utiles sur la meilleure façon d’intégrer votre RC-1590 au sein de votre
système ainsi que des informations qui vous aideront à en obtenir les
meilleures performances sur le plan sonore. N’hésitez pas à contacter votre
revendeur agréé Rotel pour obtenir les réponses à toutes les questions que
vous pourriez vous poser. En outre, nous sommes toujours heureux, chez
Rotel, de recevoir vos toutes vos remarques et commentaires.
Conservez soigneusement le carton du RC-1590 ainsi que tous les éléments
servant à l’emballage pour un usage futur éventuel. En effet, expédier ou
déménager l’amplicateur dans quoique ce soit d’autre que son carton
d’origine peut avoir pour conséquence d’endommager gravement votre
RC-1590.
Remplissez et renvoyez la carte d’enregistrement du propriétaire qui est jointe
à votre produit, et conservez en lieu sûr la facture originale. Elle constitue
votre meilleure preuve de date d’achat au cas où vous auriez besoin de
faire appliquer la garantie constructeur.
Installation
Comme tous les appareils audio faisant transiter des signaux de faible
intensité, le RC-1590 pourra être affecté par son environnement. Évitez de
disposer l’amplicateur sur d’autres éléments du système. Éviter également
de faire passer les câbles transportant le signal audio à proximité des
cordons secteur. Cela réduira au minimum les problèmes potentiels de
parasites ou de bruit de fond.
Nous vous conseillons de disposer le RC-1590 dans un meuble conçu pour
intégrer des éléments audio domestiques. De tels meubles sont spécialement
fabriqués pour réduire ou supprimer les vibrations qui peuvent affecter la
qualité sonore. Prenez conseil auprès de votre revendeur agréé Rotel sur
un choix du meuble et pour une installation correcte de vos éléments audio.
Le RC-1590 est fourni avec une télécommande infra-rouge RR-AX100. Il doit
être placé de façon à ce que le signal infra-rouge émis par la télécommande
puisse atteindre sans rencontrer d’obstacle le capteur de télécommande
situé en face avant.
Câbles
Les cordons secteur, les câbles numériques et les câbles de modulation
transportant le signal audio devront être si possible éloignés les uns des
autres. Cela pour réduire au minimum le risque que le signal audio puisse
être affecté par des interférences ou parasites provenant des câbles secteur
ou numériques. Utilisez uniquement des câbles de haute qualité. Les câbles
blindés sont particulièrement indiqués pour réduire le bruit de fond et les
parasites qui viendraient dégrader la qualité sonore de votre système. Pour
toutes ces questions, consultez votre revendeur agréé Rotel, qui pourra vous
conseiller sur le choix du meilleur câble à utiliser avec votre système audio.
Télécommande infrarouge RR‑AX100
Les commandes peuvent être effectuées depuis les boutons de la face avant,
ou via la télécommande RR-AX100 fournie avec le produit. Dans ce manuel,
les lettres et nombres entourés d’un carré se réfèrent aux commandes
exécutables au niveau de la face avant de l’appareil et, respectivement,
celles qui sont entourés d’un rond par la télécommande.
Code de télécommande pour un second amplificateur
Le code usine de la télécommande est le Code 1. Si vous constatez que
votre télécommande est en conflit avec d’autres amplificateurs Rotel, vous
pouvez changer le code de télécommande par le Code 2 en suivant les
instructions suivantes.
1. Sur la télécommande appuyez simultanément sur les touches Tuner Let
2 M pour préparer la télécommande à envoyer le Code Audio 2.
2. Pointez la télécommande vers l’appareil et a ppuyez sur la touche 2 M
pendant 8 secondes. L’appareil va afficher le message « Audio Custom
Code 1 ->2 ».
3. Répétez l’opération ci-dessus en appuyant sur la touche « 1 » au lieu de
la touche « 2 » pour repasser l’appareil sur le Code 1.
REMARQUE : Vous pouvez utiliser votre télécommande pour le pilotage
des fonctions de base de tuners et lecteurs de CD Rotel, notamment par
les groupes de touches repérées IKMN. Pour un fonctionnement
correct de votre système, assurez-vous que la télécommande, le lecteur
de CD et le Tuner, utilisent bien tous le même code de télécommande.
Pour plus d’informations, n’hésitez pas à prendre conseil auprès de
votre revendeur agréé Rotel.
Piles de la télécommande
Deux piles de type AA (fournies) doivent être insérées dans la télécommande
au préalable à son utilisation. Pour mettre en place les piles, enlever le
couvercle situé à l’arrière de la RR-AX100. Insérer les piles comme indiqué
sur le Figure. Faites un test de fonctionnement, puis remettez le couvercle
en place. Lorsque les piles deviennent faibles, la télécommande ne pourra
plus piloter correctement le RC-1590. Installez alors des piles neuves pour
éliminer le problème.