RouterBOARD MikroTik mAP 2nD User manual

RouterBOARD mAP
Quick Setup Guide and Warranty Information
The mAP is a small AP device with 2 ethernet ports, Ether1 supports powering by PoE, ether 2 supports PoE output for powering
another device.
Connecting
1. Connect your nternet cable to port 1, and your PC to port 2. f using the mAP to power another router using the PoE
output feature, connect the router to Ether 2, and use the built in wireless AP to configure the mAP
2. Set computer/router P configuration to automatic (DHCP)
3. Wireless AP mode is enabled by default, you can connect to the SS D “MikroTik”. Log into your router from your web
browser by opening 192.168.88.1 in the address bar
4. The Ether 2 port suports PoE output, with auto detection feature. This means you can connect Laptops and other non-
PoE devices without damaging them. The PoE on Ether2 outputs approximately 2V below input voltage, and supports up
to 0.5A (So provided 24V PSU will provide 22V/0.5A output to the Ether2 PoE port).
Powering
The device accepts powering from the power jack or from the first Ethernet port (Passive PoE):
DC power jack (5.5mm outside and 2mm inside diameter, female, pin positive plug) accepts 8-57V DC
The first Ethernet port accepts passive Power over Ethernet 8-57V DC.
mAP can also be powered with the built in microUSB port, using the USB 5V power
Under maximum load, the power consumption of this device is 4W (when not using PoE output)
Booting process
The device is preinstalled with MikroTik RouterOS software. t can be configured in several ways.
This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet
cable. Connect to wireless SS D “MikroTik” and open 92. 68.88. in your web browser. Username is admin and
there is no password. n case P connection is not available, Winbox can be used to connect to the MAC address of
the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup
n case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of
the device when starting it until the LED light turns off, then release the button and the device will start looking for
Netinstall servers.
By default, the device is preconfigured with a simple firewall on the WAN port, this configuration can be viewed when
first connecting to the Router via Winbox. t will ask whether to keep this configuration or clean it to use your own.
LAN/WLAN ports have DHCP server enabled.
Extension Slots and Ports
Two 10/100 Ethernet ports, supporting automatic cross/straight cable connection (Auto MD /X), so you can use either
straight or cross-over cables for connecting to other network devices.
One ntegrated Wireless 2.4GHz 802.11b/g/n 1x1 M MO, Onboard P F antennas, max gain 1.2dBi
One microUSB 2.0 port
Resetting the device
n case you wish to return the device to its original configuration, you can use the RESET button which is located to
the left of the Ethernet ports. Hold this button during boot time until LED lights start flashing, then release the button
to reset RouterOS configuration. You can use this procedure if you have forgotten the password to access the
device, or simply wish to return the unit to its default configuration state.
 
https://arttel.ru/
https://arttel.ru/

Buttons and Jumpers
RouterOS reset jumper hole (on the bottom of case, behind one of the rubber feet) – resets RouterOS software to
defaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold
screwdriver in place until RouterOS configuration is cleared.
The reset has three functions:
1. Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration
(total 5 seconds)
2. Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds)
3. Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the RouterBOARD
look for Netinstall servers (total 15 seconds)
Operating System Support
Currently tested operating system is MikroTik RouterOS starting from version 6.21
Copyright and Warranty information
Copyright MikroTikls S A. This document contains information protected by copyright law. No part of it may be
reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,
RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls S A. All trademarks and registered trademarks
appearing in this document are the property of their respective holders.
Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from the
shipping date to be free of defects in materials and workmanship under normal use and service, except in case of
damage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due to
wind, rain, fire or other acts of nature.
To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)
procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA
process.
1. f you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and
repair issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik in Latvia.
2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for: CCR1016-12G,
CCR1016-12G-BU, CCR1036-12G-4S, RB1100, RB1100AH, RB1100AHx2, RB1200, RB600, RB600A and RB800 as a paid
service (fees apply).
3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the sender at sender's
cost. f the customer has not organized return of such rejected devices within 12 months from the day of arrival, MikroTik has
the right to discard them.
RMA nstructions are located on our webpage here: http://rma.mikrotik.com
This document is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,
the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort
to ensure the accuracy of the contents of this document, however, it is possible that it may contain technical
inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for
direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, but
not limited to, loss of data or profits. Please report any inaccuracies found to [email protected]
 
https://arttel.ru/
https://arttel.ru/

Federal Communication Commission Interference Statement
(FCC ID: TV7RBMAP2N)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. f this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
ncrease the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
23 cm minimum distance has to be maintained between the antenna and the occupational user and 75 cm to general
public. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled
environment can be satisfied.
 
https://arttel.ru/
https://arttel.ru/

CE Declaration of Conformity
Full Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/
 !"#$ %&'()*+,-.*/)0#$$ +,1-+2,0+#$$#$#33
3444565
27!2#" 89:;<=>?@<='()*+,-.*/)0A@BC:DED:'F@ +,1-+2,0+@G;H=<G@<;<GE@;H;;H?@;<G@9E<@EIE;BG:9E>EADJKE<@LDEC=MENE
D:IL=D@AOE9:PED@B<EG:444565
Q!R$ ()*+,-.*/)0S$#TU'V+,1-+2,0+#WURX#YV3&3T$ZY#TX3[444565
*!$ 1"()*+,-.*/)0#\$3']#"& +,1-+2,0+3$#3\#"3"]3"#33
3444565^
!7 %#_()*+,-.*/)0$7_ +,1-+2,0+`""#"0"
a"$#_""2"+$#4445657b
! *_#3"()*+,-.*/)0 +,1-+2,0+333444565`c$c#U3
#3##U$#_#
7+!7 defghijklmnjlojfjnoemjnfgn()*+,-.*/)0pgqrheslfs+,1-+2,0+nmddlktrhefjsiklnfsnlmnsrpesnjijsfgnesnojsfsn
qlsiennuefsoenpsjfjvesnfgnlpgwsjn444565eo
!$ x#'()*+,-.*/)0# +,1-+2,0+###&y"#3#
3444565
)-!)# #()*+,-.*/)0$$ +,1-+2,0+zR####R
###{3444565
/|!/3 0T()*+,-.*/)0#}'+,1-+2,0+#~3444565*•U€•€~U
/-!/$ ‚()*+,-.*/)0#U'T+,1-+2,0+#34445652&3
%1!%" 0()*+,-.*/)0RR#U#'$"& +,1-+2,0+SƒR„#UYR#3…†3#„&„X444565*
X&#3"$XR‡3Rˆ#R„
 /!$ %U3#()*+,-.*/)0$## +,1-+2,0+3"‰##3
#"3$#U4445657
x/!x#$ UR&()*+,-.*/)0#UŠ +,1-+2,0+UR"&RRR&&"&‹Œ&
&&&444565
x-!x" '()*+,-.*/)0#+,1-+2,0+3c#33444565
+,!+ xR'()*+,-.*/)0#••# +,1-+2,0+Ž•#•#•#3#
3444565
*!#3 ()*+,-.*/)0‘3&$#U'V+,1-+2,0+’WRX#„V3&3T&Y#T„3444565
)!#3 ()*+,-.*/)0RU3#U'U+,1-+2,0+3#R3R$3"#3#“#3444565
^)!^$ ()*+,-.*/)03‡_‡_ +,1-+2,0+&&#3444565”###3U_3
3$U
!$ Härmed intygar M KROTĪKLS S A att denna RouterBOARD är i överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
 ,! " ()*+,-.*/)0#\$3+,1-+2,0+3"#""3"]3"#333444565^
EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More
information on http://wiki.mikrotik.com BG. Инструкция: Свържете адаптера на захранване , за да включите устройството. Отворете
192.168.88.1 в уеб браузър, за да настроите продукта. Повече информация в http://wiki.mikrotik.com CZ. Návod k použití : Připojte napájecí
adaptér k zapnutí přístroje. Otevřete 192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete v
http://wiki.mikrotik.com DK. Instruktionsbog: Tilslut strømadapteren for at tænde for enheden . Åbn 192.168.88.1 i en webbrowser til at
konfigurere produktet . Mere information i http://wiki.mikrotik.com FR. Mode d'emploi : Connectez l'adaptateur d'alimentation pour allumer
l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://wiki.mikrotik.com DE.
Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät einzuschalten. Öffnen Sie 192.168.88.1 in einem Web- Browser, um das
Produkt zu konfigurieren . Weitere nformationen im http://wiki.mikrotik.com EE. Kasutusjuhend : Ühendage toiteadapter seadme
sisselülitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual de instrucciones:
Conecte el adaptador de alimentación para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto . Más
información en http://wiki.mikrotik.com IT. Manuale di istruzioni : Collegare l'adattatore di alimentazione per accendere l'unità. Aprire
192.168.88.1 in un browser Web per configurare il prodotto . Maggiori informazioni in http://wiki.mikrotik.com LV. Lietošanas instrukcija :
Pievienojiet Strāvas adapteri, lai ieslēgtu ierīci. Atvērt 192.168.88.1 ar interneta pārlūku , lai konfigurētu produktu. Plašāka informācija
http://wiki.mikrotik.com LT. Naudojimosi instrukcija : Prijunkite maitinimo adapterį įjunkite įrenginį. Į interneto naršyklę 192.168.88.1 Atidarykite
galite konfigūruoti gaminį . Daugiau informacijos rasite http://wiki.mikrotik.com HU. Használati utasítás : Csatlakoztassa a hálózati adaptert a
készülék bekapcsolásához . Megnyitása 192.168.88.1 egy webböngészőben beállítani a terméket. Több információ http://wiki.mikrotik.com NL.
Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen . Open 192.168.88.1 in een webbrowser om het product te configureren.
Meer informatie in http://wiki.mikrotik.com PL. I nstrukcja obsługi : Podłącz adapter zasilania, aby włączyć urządzenie. Otwórz 192.168.88.1 w
przeglądarce internetowej , aby skonfigurować urządzenie . Więcej informacji w http://wiki.mikrotik.com PT. Manual de instruções : Conecte o
adaptador de alimentação para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto . Mais informações em
http://wiki.mikrotik.com RO. Instrucțiuni de utilizare : Conectați adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 într-un
browser web pentru a configura produsul . Mai multe informații în http://wiki.mikrotik.com SK. Návod na použitie: Pripojte napájací adaptér k
zapnutiu prístroja. Otvorte 192.168.88.1 vo webovom prehliadači pre konfiguráciu produktu. Viac informácií nájdete v http://wiki.mikrotik.com SI.
Navodila: Priključite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Več informacij v
http://wiki.mikrotik.com FI. Käyttöohje: Kytke virtalähde päälle laitteen. Avaa 192.168.88.1 in selaimen määrittää tuotteen . Lisää tietoa
http://wiki.mikrotik.com SE. Instruktionsmanual: Anslut nätadaptern för att slå på enheten . Öppna 192.168.88.1 i en webbläsare för att
konfigurera produkten . Mer information på http://wiki.mikrotik.com NO. Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne
192.168.88.1 i en nettleser for å konfigurere produktet . Mer informasjon på http://wiki.mikrotik.com GR. εγχειρίδιο οδηγιών: Συνδέστε τον
προσαρμογέα τροφοδοσίας για να ενεργοποιήσετε τη μονάδα . Ανοίξτε 192.168.88.1 σε ένα πρόγραμμα περιήγησης στο Web για να
διαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο http://wiki.mikrotik.com
 
https://arttel.ru/
https://arttel.ru/