Rowenta INTENSE PURE AIR XL PU6020 Series User manual

www.rowenta.com
INTENSE PURE AIR
PU4020xx/PU6020xx
1800146415-02
FR
ES
EN

A
D
E
F
G
H
I
F
B
C
1
6 7 8 9 10
2 3 4 5

3
DESCRIPTION
Product description
A Ambient light
B Adjustable air outlet grid
C Control panel
D Front door
E Handle
F Air inlets
G Particle sensor
H Gas sensor ( PU6020 full size only)
I Power cord outlet
Control panel Lights
1 Filter replacement indicator
2 Air quality indicator
3 Filtration speed
4 Mode (auto, night, manual)
5 Timer / delayed start
Control buttons
6 Light
7 Filter reset
8 Start
9 Mode/filtration speed
selection
10 Timer / delayed start set-
ting
DESCRIPTION
Descriptif Produit
A Lumière d’ambiance
B Grille de sortie d’air
orientable
C Bandeau de commande
D Porte avant
E Poignée
F Entrées d’air
G Capteur de particules
H Capteur de gaz (PU6020
modèle XL seulement)
I Sortie cordon électrique
Voyants
1 Indicateur de changement
des filtres
2 Indicateur de qualité d’air
3 Vitesse de filtration
4 Mode (auto, nuit, manuel)
5 Timer / départ différé
Boutons de commande
6 Lumière
7 Réinitialisation des filtres
8 Mise en marche
9 Sélection du mode / vitesse
de filtration
10 Réglage timer / départ dif-
féré
DESCRIPCIÓN
Descripción del producto
A Luz ambiental
B Rejilla de salida del aire orien-
table
C Panel de control
D Puerta delantera
E Tirador
F Entradas de aire
G Sensor de partículas
H Sensor de gases (única-
mente en PU6020)
I Salida del cable de alimenta-
ción
Panel de control Indicadores
1 Indicador de cambio de
filtros
2 Indicador de calidad del
aire
3 Velocidad de filtración
4 Modo (auto, noche, ma-
nual)
5 Temporizador/Inicio retar-
dado
Botones de control
6 Luz
7 Reposición de los filtros
8 Puesta en marcha
9 Selección de la velocidad
de filtración
10 Ajuste del temporizador /
inicio retardado

4
DISASSEMBLING/REASSEMBLING FILTERS
CLICK !CLICK !
CLICK !
CLICK !
1 2 3
6 7 8 9
54
CLICK !CLICK !
CLICK !CLICK !
CLICK !
CLICK !
1 2 3 6 7 8 9
54
CLICK !CLICK !
CLICK !CLICK !
CLICK !
CLICK !
1 2 3 6 7 8 9
54
CLICK !CLICK !
Montage/Démontage des Filtres - Instalación/Desmontaje de los filtros

5
EN
READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS PURIFIER.
SAFETY INSTRUCTIONS
WARNINGS
It is essential that you read these instructions carefully and comply with the following
recommendations.
• For your safety, this appliance complies with the applicable
standards and regulations (Low Voltage Directive,
Electromagnetic Compatibility, Environmental…).
• If the power cord is damaged it must be replaced by the
manufacturer, the manufacturer’s after-sales service department
or a similarly qualified person, to avoid danger.
• WARNING: To reduce the risk of fire or electrical shock, do not
use this appliance with any solid-state speed control device.
• Do not use your appliance in a dusty room or a room where
there is a risk of fire.
• Before using, always check the condition of the appliance, the
power outlet and the power lead.
• Improper installation may result in the risk of fire, electric shock
or personal injury.
• The power plug must be removed from the power outlet when
not in use, before cleaning, servicing, and maintenance and
before moving to another location.
• Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area and
where it will not be tripped over.
• Do not operate any appliance with a damaged cord or plug.
Discard fan or return to an authorized service facility for
examination and /or repair.
• Do not pull on the power cord or the appliance, even to unplug
it from the wall outlet.
• Never insert objects into the appliance (e.g. needles...).
• Do not use gasoline, thinners, solvents, ammonias or other
chemicals for cleaning.
• The warranty will be void in the event of damage arising from
improper use.
• Do not attempt to repair or replace parts.
• This appliance is intended for domestic use only. It must
therefore not be used in industrial applications.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,

6
or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
• This appliance may be used by children aged 8 or over, and by
persons lacking appropriate knowledge and experience or whose
physical, sensory or mental capacities are limited, provided that
they are supervised, have received instruction in the safe use of
the appliance, and are fully aware of the risks involved. Children
must not be allowed to play with the appliance. Home cleaning and
maintenance of the appliance must not be carried out by children
unless they are aged 8 or over and are supervised. Always keep the
appliance and power cord out of reach of children under 8 years.
VERY IMPORTANT
• Do not cover the air inlets or the outlet grid.
• Do not touch the appliance with wet hands.
• Never allow any liquid to enter the appliance.
• Never use the appliance in a humid place.
• Never use the appliance close to a heat source.
• Never place anything on the appliance or insert anything into it.
• Do not use the appliance close to flammable objects or products (curtains, aerosols, solvents, etc.).
• Never use the appliance in an inclined or horizontal position. Place the appliance on a flat, stable
surface.
• In the case of prolonged absence: switch the appliance off using the button (8) and unplug it.
• Switch off and unplug your appliance before moving it.
• Unplug the air purifier during assembly and cleaning.

7
EN
*Ranking established by the ANSES, French Agency for Food, Environmental and Ocupational Health and Safety, 2010
OPERATING PRINCIPLE
The new Intense Pure Air purifier from Rowenta enables you to breathe up to 99.99% pure air
in your home and protect your health with 4 filtration levels as described below. Each level is
essential and traps specific pollutants :
LEVEL 3:
TRUE HEPA
ALLERGY+FILTER
• Fine particles
(PM2.5)
• Pollen
• Dust mites
• Animal allergens
• Mold
• Bacteria / viruses
LEVEL 1:
PRE-FILTER
• Dust
• Hair
• Fur
• Lint
LEVEL 2:
ACTIVE CARBON
FILTER
• Volatile organic
components (VOCs)
• Odors / gases
LEVEL 4:
NANOCAPTUR
FILTER
• Formaldehyde
Formaldehyde is the
most harmful indoor
air pollutant.*
« HOW TO ACHIEVE CLEANER INDOOR AIR »
In addition to using your Intense Pure Air purifier, here are some tips on how to
improve the quality of your indoor air:
• Ventilate the rooms for at least 10 min. every day, in summer and winter
• Maintain your ventilation system
• Limit the use of household products
• Do not smoke indoors
• Avoid home fragrances, incense sticks, scented candles, etc.
• Ventilate whenever any work is being conducted in your home and for several
weeks afterwards
• Avoid green plants that are allergenic or need frequent watering
WHERE TO INSTALL THE APPLIANCE
Place the purifier on a flat, stable surface in the room requiring treatment.
To allow the air to circulate freely, avoid placing the appliance behind curtains, below a window,
item of furniture or shelf unit, or close to any other obstacle, and leave at least 50 cm of free space
above in front of and on each side of the appliance.

8
BEFORE USING THE APPLIANCE FOR THE FIRST TIME
Make sure that the plastic packaging protecting the filters has been removed before using
the appliance.
Also make sure that:
• The voltage of your electrical installation corresponds to the one indicated on the appliance.
Your appliance can be used with a power plug without an earth connection. It is a class II appliance
(double electrical insulation),
• The appliance is positioned in the house as described above,
• The air inlet and outlet grids are completely unobstructed,
• Ensure the 4 filters and front panel have been correctly installed (see section « Disassembling /
Reassembling filters »).
This appliance is fitted with a device that automatically prevents it from operating if the front door
is not correctly assembled.
Inserting the filters
This appliance is equipped with 4 types of filters:
Pre-filter Active carbon
filter
NanoCaptur
filter
True HEPA Allergy
+ filter
NB: For optimum performance of the appliance, only use filters provided by ROWENTA.
To install the filters, follow the instructions in the section « Disassembling/Reassembling filters ».
Please note: certain filters may emit a temporary slight odour, due to the transport and storage conditions.
SWITCHING THE APPLIANCE ON
Connect the power cord and press the start button (8).
Your appliance will be preset to automatic mode the first time you turn it on.
Thanks to its infrared particles sensor and its gas sensor (model PU6020 full size only), it detects
the level of pollution in the room and automatically adjusts the filtration speed accordingly.
A light changes color to indicate the quality of air in the room.
Air quality Color of light Filtration speed
(in auto mode)
Excellent Blue
Average Purple
Poor Red

9
EN
SETTING THE POLLUTION SENSORS
The appliance is preset to medium sensitivity.
If the air quality indicator remains:
- poor after 2 hours in operation although the air seems to be purified
- excellent for more than 1 hour although the air seems to be polluted
you can adjust the sensor sensitivity as follows:
1. When the air purifier is off, hold down the filtration speed setting button for 2 seconds:
2. Set the sensitivity by briefly pressing the filtration speed setting button:”
+ Blue + Purple + Red
Low sensitivity Medium sensitivity High sensitivity
Select high sensitivity if the air purifier indicates excellent air quality for more than 1 hour although
the air seems to be polluted.
• Select low sensitivity if the air purifier continues to indicate poor air quality even though it has
been operating for more than 2 hours and the air seems sufficiently purified.
3. The new setting is applied if no button is pressed for 10 seconds.
OPERATION
START
Briefly press this button to switch the air purifier on or off.
MODE/FILTRATION SPEED SELECTION
Automatic: In this operating mode, the filtration speed automatically adjusts according to the
air quality detected by the particles sensor and the gas sensor (model PU6020 full size only). This
mode is recommended for general use.
Night: The filtration speed of your appliance is adjusted for a whisper quiet air flow during the
night. The light intensity of the appliance is also reduced. If pollution is detected, the filtration
speed increases slightly to purify your air but remains quiet to avoid disturbing your sleep.
Manual: In this operating mode, you can manually select 1 of the 4 filtration speeds.
LIGHT
You can change the light intensity of the appliance as you wish or according to the time of day.
Press Ambient light Air quality indicator Control panel
1 Light up Light up Light up
2 Moderate light Moderate light Moderate light
3 Off Moderate light Moderate light
4 Off Off Moderate light
TIMER / DELAYED START
If the appliance is on: you can use the button 10 to define the operating duration. Briefly press
the button to select the number of operating hours desired (1, 2, 4 or 8) and the appliance will
automatically turn off at the end of the selected period.
If the appliance is off: briefly press the button 10 to set the appliance to turn on in a certain number
of hours (1, 2, 4 or 8).

10
3D PURE AIR FUNCTION (adjustable grid)
You can adjust the position of the air outlet grid manually, as desired. For an optimum, even flow
of purified air in the room, set the angle to 45°; for optimized well-being, set the angle to 90°.
MAINTENANCE
Always switch the appliance off with the button (8) and unplug it before conducting any
maintenance operation.
You can clean the outer of the appliance with a slightly damp cloth.
IMPORTANT: Never use abrasive products which could damage your appliance’s appearance.
FILTERS
Filter Action Cycles
Pre-filter Clean Every 2 to 4 weeks
Active carbon filter Replace Every 12 months
True HEPA Allergy+ filter Replace Every 2 years
NanoCaptur filter Replace Color changing
(see Color chart on filter)
This data is based on an average use of 8 hours per day at speed 2.
The recommended frequency for cleaning and replacing the filters may vary depending on the
duration of use and the operating environment.
• A “HEPA” light indicates when the HEPA filter needs to be replaced.
The ‘Odor’ light indicates when the carbon filter needs to be replaced.
• The NanoCaptur filter contains translucent granules which change color according to the
formaldehyde absorption rate. Refer to the color chart on the inside of the panel or the filter itself
to establish the filter saturation rate.Once the saturation rate has reached its maximum, the filter
must be replaced. You have to check the filter saturation rate every six months.
• The pre-filter can be re-used: remove the dust using a vacuum cleaner or wash with water.
CAUTION:
• The appliance’s efficiency can be reduced if the pre-filter is not cleaned regularly.
• Never use a pre-filter that is still damp.
• The pre-filter is the only filter which can be re-used and washed with water. The HEPA,
NanoCaptur and active carbon filters cannot be cleaned and re-used. Never wash with water.
• To replace the filters, follow the instructions in the section « Disassembling/Reassembling
filters ».
Your replacement filters are available under the following codes:
Filter Code PU4020 mid. size Code PU6020 full size
True HEPA Allergy+ filter XD6074 XD6077
Active carbon filter XD6065 XD6066
Nanocaptur filter XD6085 XD6086
IMPORTANT: Resetting the filters
The reset light flashes when a filter needs to be replaced. Once the filter has been replaced, hold
down the reset button for 2 seconds. .