Rowlett CU742-A User manual

Model:
CU742-A
Hand blender
Instruction manual
CU742-A_A5_v1_20230606.indb 1CU742-A_A5_v1_20230606.indb 1 2023/6/6 15:042023/6/6 15:04

2
EN Telephone Helpline: 1300225960
Safety Instructions
Please take a few moments to carefully read through this manual. Correct maintenance and operation
of this machine will provide the best possible performance from your Rowlett product. Save these
instructions.
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
• Before use check that the voltage of your power supply
corresponds to the one shown on the rating plate.
• DO NOT operate the unit if damaged.
• To protect against electrical shock, do not put motor unit in
water or any other liquid.
• Blade is sharp – handle carefully.
• The use of accessory attachments not recommended or sold
by Rowlett may cause fire, electric shock, or injury, which will
invalidate your guarantee.
• DO NOT remove food from the appliance until the blending
attachments have come to a complete stop.
• Avoid contacting moving parts. Keep hands, hair, clothing and
utensils away from blending attachment and container while
operation to prevent the possibility of severe injury to persons
and/or damage to the appliance.
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT use to blend hard and dry substances. Otherwise the
blade could be blunted.
• Do not let cord hang over edge of table or hot surface.
• Do not blend hot liquids.
CU742-A_A5_v1_20230606.indb 2CU742-A_A5_v1_20230606.indb 2 2023/6/6 15:042023/6/6 15:04

3
AUEN
Telephone Helpline: 1300225960
• Always switch off and disconnect from the power supply
when not in use, before putting on or taking off parts, before
approaching moving parts, and before cleaning. Always
disconnect the blender from the power supply if it is left
unattended.
• Not suitable for outdoor use.
• Keep all packaging away from children. Dispose of the
packaging in accordance to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a
Rowlett agent or a recommended qualified technician in order
to avoid a hazard.
• This appliance can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand
the hazards involved.
• Close supervision is necessary when your appliance is being
used near children or infirm persons.
• This appliance shall not be used by children. Keep the
appliance and its cord out of reach of children. Do not allow
children to use the blender without supervision.
• Rowlett recommend that this appliance should be periodically
tested (at least annually) by a Competent Person. Testing
should include, but not be limited to: Visual Inspection,
Polarity Test, Insulation Continuity and Functional Testing.
Pack Contents
The following is included:
• Hand blender
• Shaft
• Blending jar
• Attachment adapter
• Balloon whisk
• Chopper lid
• Chopper blade
• Chopper bowl
• Instruction manual
Rowlett prides itself on quality and service, ensuring that at the time of unpacking the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your Rowlett dealer immediately.
CU742-A_A5_v1_20230606.indb 3CU742-A_A5_v1_20230606.indb 3 2023/6/6 15:042023/6/6 15:04

4
EN Telephone Helpline: 1300225960
Assembly
TURBO button
Attachment adapter
Chopper lid
Power button
Speed selector
Motor unit
Shaft
Measuring jug
Chopper blade
Chopper bowl
Balloon whisk
CU742-A_A5_v1_20230606.indb 4CU742-A_A5_v1_20230606.indb 4 2023/6/6 15:042023/6/6 15:04

5
AUEN
Telephone Helpline: 1300225960
Before assembly, ensure to clean all parts that come into contact
with food with warm soapy water. For details, refer to section
“Cleaning, care & maintenance”.
Blades are very sharp! Be careful when handling blades,
especially when emptying the bowl and during cleaning.
Rowlett accept no responsibility for any injury caused by incorrect
assembly/disassembly.
Mounting blender shaft
1. Align the arrow mark on the shaft with the Eject button on the
motor unit.
2. Insert the shaft into motor part until locked in place.
Mounting balloon whisk
1. Insert the balloon whisk into the attachment adapter.
2. Mount the adapter onto the motor unit.
Eject button
Mounting chopper assembly
• Always ensure the chopper bowl is in place before inserting the chopper blade.
• Be sure the chopper lid is locked in place before operation.
1. Place the chopper bowl on a flat surface, then insert the chopper blade.
2. Add food in the bowl and locate the chopper lid.
3. Fix one end of the attachment adapter on the motor unit, then the other end on the chopper lid.
Operation
Blending Beating/whisking Chopping
• Lower the shaft or balloon whisk into food.
• Connect the appliance to the power supply.
• Press and hold the power button to start. If desired, use the speed selector to adjust the speed.
• During operation, you can also press the “TURBO” button to run at the highest speed. In turbo
mode, do not let the motor run for more than 15 seconds.
• After each use, release the power button or “TURBO” button to stop. Disconnect from power
supply and let attachments come to a full stop.
• To remove the attachments, hold them with one hand and press the Eject button with the other
hand.
Max working time per cycle:
1 minute
Interval during cycles: 3 minutes
Max working time per cycle:
2 minutes
Interval during cycles: 10 minutes
Max working time per cycle:
30 seconds
Interval during cycles: 10 minutes
• Be careful of potential injury from misuse.
• During use, never let the blending attachments face towards people or objects. Risk of
damage or injury!
• It is recommended to tilt the bender slightly to prevent the blade guard from touching
the bottom of the container.
CU742-A_A5_v1_20230606.indb 5CU742-A_A5_v1_20230606.indb 5 2023/6/6 15:042023/6/6 15:04

6
EN Telephone Helpline: 1300225960
Removing the lodged food
If a piece of food gets lodged onto the
attachments, please follow the instructions below:
1. Release the power button to stop, then
disconnect from power supply and let it come
to a complete stop.
2. Press the Eject button to release the
attachments, then use a rubber/wooden
spatula to remove the food lodged. Caution:
The blade is sharp - Never attempt to use
fingers to remove any lodged object.
Recipe
Recipe below is provided for references only.
Blending carrot into pulp:
Attachment: shaft
Instructions: Put 280g carrot (pre-cut into pieces)
and 420g water into the measuring jug; Start with
low speed then use Turbo function for 15 seconds.
Repeat the cycle until carrot is blended into fine
pulp.
Chopping meat:
Attachment: Chopper assembly
Instructions: Remove bone from meat, cut meat
into pieces and put in the bowl. Max quantity of
meat cannot exceed 200g in every processing.
Start with low speed then use Turbo function for
15 seconds. Repeat the cycle until meat is minced.
Beating egg white into foaming shape:
Attachment: Balloon whisk
Instructions: Pour egg white in the jug. Normally
2 eggs’ white is enough. Run the appliance for 2
minutes and repeat if necessary.
Cleaning, Care &
Maintenance
• Before cleaning, always disconnect motor
unit from power supply, let it cool down
and come to a full stop.
• Clean the motor unit surface with a damp
cloth. Never immerse the motor part in water
or rinse it under running water.
• Use warm soapy water to clean blending
attachments, jug and bowl. Do not use
abrasive cleaning chemicals as these can leave
harmful residues.
• Dry all parts thoroughly after cleaning.
• Always dry the blades well after
cleaning to avoid spotting.
• Measuring jug and chopper bowl can
not be used to store food for long time.
Quick cleaning
Between processing tasks, hold the blender in a
container half filled with water and let it run for a
few seconds (Never exceeding 15 seconds).
Troubleshooting
A qualified technician must carry out repairs if required.
Fault Probable Cause Solution
The appliance is
not working
The unit is not switched on Check the unit is plugged in correctly and
switched on
Plug or lead is damaged Replace plug or lead
Mains Power supply fault Check Mains Power supply
Appliance slows
down
Too many contents in the
container
Turn off the unit and remove some of the
contents. Adjust the food formula if needed
Wrong mixing attachment used Select suitable attachment
Loud noise Mixing attachments not correctly
fitted
Remove and refit attachments
Mixing attachments deforms Contact a qualified technician
CU742-A_A5_v1_20230606.indb 6CU742-A_A5_v1_20230606.indb 6 2023/6/6 15:042023/6/6 15:04

7
AUEN
Telephone Helpline: 1300225960
Technical Specifications
Note: Due to our continuing program of research and development, the specifications herein may be
subject to change without notice.
Model Voltage Power Dimensions
H x W x D mm
Weight
(kg)
CU742-A 220-240V~, 50Hz 300W 416 x 56 x 56 1.33kg
Electrical Wiring
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Compliance
The product must not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and environmentally safe
recycling process. For further information on how to dispose of this product correctly, contact the product
supplier, or the local authority responsible for waste disposal in your area.
Rowlett parts have undergone strict product testing in order to comply with regulatory
standards and specifications set by international, independent, and federal authorities.
Rowlett products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of Rowlett.
Every effort is made to ensure all details are correct at the time of going to press, however, Rowlett reserve the right to
change specifications without notice.
CU742-A_A5_v1_20230606.indb 7CU742-A_A5_v1_20230606.indb 7 2023/6/6 15:042023/6/6 15:04

DECLARATION OF CONFORMITY
• Conformiteitsverklaring • Déclaration de conformité • Konformitätserklärung • Dichiarazione di conformità •
• Declaración de conformidad • Declaração de conformidade
Equipment Type • Uitrustingstype • Type d'équipement • Gerätetyp
• Tipo di apparecchiatura • Tipo de equipo • Tipo de equipamento
Model • Modèle • Modell • Modello
• Modelo • Malli
Hand Blender
CU742-A
Application of Territory Legislation &
Council Directives(s)
Toepassing van Europese Richtlijn(en)
• Application de la/des directive(s) du
Conseil • Anwendbare EU-Richtlinie(n)
• Applicazione delle Direttive
• Aplicación de la(s) directiva(s) del
consejo • Aplicação de directiva(s) do
Conselho
Electrical Safety
AS/NZS 60335.1:2020
AS/NZS 60335.2.14:2017 +A1
Electro-Magnetic Compatibility (EMC)
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 61000-3-2: 2019 +A1:2021
EN 61000-3-3: 2013 +A1:2019 +A2:2021
Producer Name • Naam fabrikant • Nom du producteur • Name des Herstellers
• Nome del produttore • Nombre del fabricante • Nome do fabricante
Rowlett
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s)
and Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande
Richtlijn(en) en Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und
Norm(en) entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y
estándar(es) arriba mencionadas.
Eu, o abaixo-assinado, declaro que o equipamento anteriormente especificado está em conformidade com a(s) anterior(es)
Directiva(s) e Norma(s)
Date • Data • Date • Datum • Data •
Fecha • Data
26th May 2023
Signature • Handtekening • Signature
• Unterschrift Firma • Firma •
Assinatura
Full Name • Volledige naam • Nom et
prénom • Vollständiger Name • Nome
completo • Nombre completo • Nome
por extenso
Ashley Hooper
Brendan Denmeade
Position • Functie • Fonction • Position
• Qualifica • Posición • Função
Technical & Quality Manager
Commercial Manager/ Responsible
Supplier
Producer Address • Adres fabrikant •
Adresse du producteur • Anschrift des
Herstellers • Indirizzo del produttore •
Dirección del fabricante • Morada do
fabricante
Fourth Way,
Avonmouth,
Bristol,
BS11 8TB
United Kingdom
15 Bagdally Road,
Campbelltown
NSW 2560
DocuSign Envelope ID: ECEA4536-5C5F-42F9-BC7A-AC7E39A1D526
CU742-A_A5_v1_20230606.indb 8CU742-A_A5_v1_20230606.indb 8 2023/6/6 15:042023/6/6 15:04

CU742-A_A5_v1_20230606.indb 9CU742-A_A5_v1_20230606.indb 9 2023/6/6 15:042023/6/6 15:04

CU742-A_A5_v1_20230606.indb 10CU742-A_A5_v1_20230606.indb 10 2023/6/6 15:042023/6/6 15:04

CU742-A_A5_v1_20230606.indb 11CU742-A_A5_v1_20230606.indb 11 2023/6/6 15:042023/6/6 15:04

CU742-A_A5_v1_2023/06/06
CU742-A_A5_v1_20230606.indb 12CU742-A_A5_v1_20230606.indb 12 2023/6/6 15:042023/6/6 15:04