Rowlett FB973 User manual

Model • Modèle • Modell • Modello • Modelo • Malli:
FB973
Hand blender
Instruction manual
FB973_EN_A5_v1_20220826.indb 1FB973_EN_A5_v1_20220826.indb 1 2022/8/26 16:062022/8/26 16:06

2
EN
Safety Instructions
Please take a few moments to carefully read through this manual. Correct maintenance and operation
of this machine will provide the best possible performance from your Rowlett product. Save these
instructions.
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
• Before use check that the voltage of your power supply
corresponds to the one shown on the rating plate.
• DO NOT operate the unit if damaged.
• To protect against electrical shock, do not put motor unit in
water or any other liquid.
• Blade is sharp – handle carefully.
• The use of accessory attachments not recommended or sold
by Rowlett may cause fire, electric shock, or injury, which will
invalidate your guarantee.
• DO NOT remove food from the appliance until the blending
attachments have come to a complete stop.
• Avoid contacting moving parts. Keep hands, hair, clothing and
utensils away from blending attachment and container while
operation to prevent the possibility of severe injury to persons
and/or damage to the appliance.
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT use to blend hard and dry substances. Otherwise the
blade could be blunted.
• Do not let cord hang over edge of table or hot surface.
• Do not blend hot liquids.
FB973_EN_A5_v1_20220826.indb 2FB973_EN_A5_v1_20220826.indb 2 2022/8/26 16:062022/8/26 16:06

3
EN
• Always switch off and disconnect from the power supply
when not in use, before putting on or taking off parts, before
approaching moving parts, and before cleaning. Always
disconnect the blender from the power supply if it is left
unattended.
• Not suitable for outdoor use.
• Keep all packaging away from children. Dispose of the
packaging in accordance to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a
Rowlett agent or a recommended qualified technician in order
to avoid a hazard.
• This appliance can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand
the hazards involved.
• Close supervision is necessary when your appliance is being
used near children or infirm persons.
• This appliance shall not be used by children. Keep the
appliance and its cord out of reach of children. Do not allow
children to use the blender without supervision.
• Rowlett recommend that this appliance should be periodically
tested (at least annually) by a Competent Person. Testing
should include, but not be limited to: Visual Inspection,
Polarity Test, Insulation Continuity and Functional Testing.
• Rowlett recommend that this product is connected to a circuit
protected by an appropriate RCD (Residual Current Device).
Pack Contents
The following is included:
• Hand blender
• Shaft
• Blending jar
• Attachment adapter
• Balloon whisk
• Chopper lid
• Chopper blade
• Chopper bowl
• Instruction manual
FB973_EN_A5_v1_20220826.indb 3FB973_EN_A5_v1_20220826.indb 3 2022/8/26 16:062022/8/26 16:06

4
EN
Rowlett prides itself on quality and service, ensuring that at the time of unpacking the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your Rowlett dealer immediately.
Operation
TURBO button
Attachment adapter
Chopper lid
Power button
Speed selector
Motor unit
Shaft
Measuring jug
Chopper blade
Chopper bowl
Balloon whisk
FB973_EN_A5_v1_20220826.indb 4FB973_EN_A5_v1_20220826.indb 4 2022/8/26 16:062022/8/26 16:06

5
EN
Assembly
Before assembly, ensure to clean all parts that come into contact
with food with warm soapy water. For details, refer to section
“Cleaning, care & maintenance”.
Blades are very sharp! Be careful when handling blades,
especially when emptying the bowl and during cleaning.
Rowlett accept no responsibility for any injury caused by incorrect
assembly/disassembly.
Mounting blender shaft
1. Align the arrow mark on the shaft with the Eject button on the
motor unit.
2. Insert the shaft into motor part until locked in place.
Mounting balloon whisk
1. Insert the balloon whisk into the attachment adapter.
2. Mount the adapter onto the motor unit.
Eject button
Mounting chopper assembly
• Always ensure the chopper bowl is in place before inserting the chopper blade.
• Be sure the chopper lid is locked in place before operation.
1. Place the chopper bowl on a flat surface, then insert the chopper blade.
2. Add food in the bowl and locate the chopper lid.
3. Fix one end of the attachment adapter on the motor unit, then the other end on the chopper lid.
Operation
Blending Beating/whisking Chopping
• Lower the shaft or balloon whisk into food.
• Connect the appliance to the power supply.
• Press and hold the power button to start. If desired, use the speed selector to adjust the speed.
• During operation, you can also press the “TURBO” button to run at the highest speed. In turbo
mode, do not let the motor run for more than 15 seconds.
• After each use, release the power button or “TURBO” button to stop. Disconnect from power
supply and let attachments come to a full stop.
• To remove the attachments, hold them with one hand and press the Eject button with the other
hand.
Max working time per cycle: 1
minute
Interval during cycles: 3 minutes
Max working time per cycle: 2
minutes
Interval during cycles: 10 minutes
Max working time per cycle: 30
seconds
Interval during cycles: 10 minutes
• Be careful of potential injury from misuse.
• During use, never let the blending attachments face towards people or objects. Risk of
damage or injury!
• It is recommended to tilt the bender slightly to prevent the blade guard from touching
the bottom of the container.
FB973_EN_A5_v1_20220826.indb 5FB973_EN_A5_v1_20220826.indb 5 2022/8/26 16:062022/8/26 16:06

6
EN
Removing the lodged food
If a piece of food gets lodged onto the
attachments, please follow the instructions below:
1. Release the power button to stop, then
disconnect from power supply and let it come
to a complete stop.
2. Press the Eject button to release the
attachments, then use a rubber/wooden
spatula to remove the food lodged. Caution:
The blade is sharp - Never attempt to use
fingers to remove any lodged object.
Recipe
Recipe below is provided for references only.
Blending carrot into pulp:
Attachment: shaft
Instructions: Put 280g carrot (pre-cut into pieces)
and 420g water into the measuring jug; Start with
low speed then use Turbo function for 15 seconds.
Repeat the cycle until carrot is blended into fine
pulp.
Chopping meat:
Attachment: Chopper assembly
Instructions: Remove bone from meat, cut meat
into pieces and put in the bowl. Max quantity of
meat cannot exceed 200g in every processing.
Start with low speed then use Turbo function for
15 seconds. Repeat the cycle until meat is minced.
Beating egg white into foaming shape:
Attachment: Balloon whisk
Instructions: Pour egg white in the jug. Normally
2 eggs’ white is enough. Run the appliance for 2
minutes and repeat if necessary.
Cleaning, Care &
Maintenance
• Before cleaning, always disconnect motor
unit from power supply, let it cool down
and come to a full stop.
• Clean the motor unit surface with a damp
cloth. Never immerse the motor part in water
or rinse it under running water.
• Use warm soapy water to clean blending
attachments, jug and bowl. Do not use
abrasive cleaning chemicals as these can leave
harmful residues.
• Dry all parts thoroughly after cleaning.
• Always dry the blades well after
cleaning to avoid spotting.
• Measuring jug and chopper bowl can
not be used to store food for long time.
Quick cleaning
Between processing tasks, hold the blender in a
container half filled with water and let it run for a
few seconds (Never exceeding 15 seconds).
Troubleshooting
A qualified technician must carry out repairs if required.
Fault Probable Cause Solution
The appliance is
not working
The unit is not switched on Check the unit is plugged in correctly and
switched on
Plug or lead is damaged Replace plug or lead
Fuse in the plug has blown Replace the plug fuse
Mains Power supply fault Check Mains Power supply
Appliance slows
down
Too many contents in the
container
Turn off the unit and remove some of the
contents. Adjust the food formula if needed
Wrong mixing attachment used Select suitable attachment
Loud noise Mixing attachments not correctly
fitted
Remove and refit attachments
Mixing attachments deforms Contact a qualified technician
FB973_EN_A5_v1_20220826.indb 6FB973_EN_A5_v1_20220826.indb 6 2022/8/26 16:062022/8/26 16:06

7
EN
Technical Specifications
Model Voltage Power Current Dimensions
H x W x D mm
Weight
(kg)
FB973 220-240V~, 50-60Hz 800W 3.48A 416 x 56 x 56 1.33kg
Note: Due to our continuing program of research and development, the specifications herein may subject
to change without notice.
Electrical Wiring
This appliance is supplied with a 3 pin BS1363 plug and lead.
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Compliance
The WEEE logo on this product or its documentation indicates that the product must
not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and
environmentally safe recycling process. For further information on how to dispose of
this product correctly, contact the product supplier, or the local authority responsible for
waste disposal in your area.
Rowlett parts have undergone strict product testing in order to comply
with regulatory standards and specifications set by international,
independent, and federal authorities.
Rowlett products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of Rowlett.
Every effort is made to ensure all details are correct at the time of going to press, however, Rowlett reserve the right to
change specifications without notice.
FB973_EN_A5_v1_20220826.indb 7FB973_EN_A5_v1_20220826.indb 7 2022/8/26 16:062022/8/26 16:06

DECLARATION OF CONFORMITY
• Conformiteitsverklaring • Déclaration de conformité • Konformitätserklärung • Dichiarazione di conformità •
• Declaración de conformidad
Equipment Type • Uitrustingstype • Type d'équipement • Gerätetyp
• Tipo di apparecchiatura • Tipo de equipo
Model • Modèle • Modell • Modello
• Modelo
Hand Blender
FB973 (& -E)
Application of Territory Legislation &
Council Directives(s)
Toepassing van Europese Richtlijn(en)
• Application de la/des directive(s) du
Conseil • Anwendbare EU-Richtlinie(n)
• Applicazione delle Direttive
• Aplicación de la(s) directiva(s) del
consejo
Low Voltage Directive (LVD) - 2014/35/EU
Electrical Equipment (Safety) Regulations 2016
(BS) EN 60335-1:2012 +A11:2014 +A13:2017 +A1:2019 +A14:2019 +A2:2019 +A15:2021
(BS) EN 60335-2-14:2006 +A1: 2008 +A11: 2012 +A12:2016
(BS) EN 62233:2008
Electro-Magnetic Compatibility (EMC) Directive 2014/30/EU - recast of 2004/108/EC
Electromagnetic Compatibility Regulations 2016 (S.I. 2016/1091)
(BS) EN IEC 55014-1:2021
(BS) EN IEC 55014-2:2021
(BS) EN IEC 61000-3-2:2019 +A1:2021
(BS) EN 61000-3-3:2013 +A1:2019
Ecodesign energy-related products Directive 2009/125/EC
Regulation (EC) 1275/2008 - Standby and off mode power consumption
EN 50564:2011
Restriction of Hazardous Substances Directive (RoHS) 2015/863 amending Annex II to
Directive 2011/65/EU
Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic
Equipment Regulations 2012 (S.I. 2012/3032)
Producer Name • Naam fabrikant • Nom du producteur • Name des Herstellers
• Nome del produttore • Nombre del fabricante
Rowlett
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s)
and Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande
Richtlijn(en) en Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und
Norm(en) entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y
estándar(es) arriba mencionadas.
Date • Data • Date • Datum • Data •
Fecha
25th August 2022
Signature • Handtekening • Signature
• Unterschrift Firma • Firma
Full Name • Volledige naam • Nom et
prénom • Vollständiger Name • Nome
completo • Nombre completo
Ashley Hooper
Eoghan Donnellan
Position • Functie • Fonction • Position
• Qualifica • Posición
Technical & Quality Manager
Commercial Manager/ Importer
Producer Address • Adres fabrikant •
Adresse du producteur • Anschrift des
Herstellers • Indirizzo del produttore •
Dirección del fabricante
Fourth Way,
Avonmouth,
Bristol,
BS11 8TB
United Kingdom
Unit 9003,
Blarney Business
Park,
Blarney,
Co. Cork
Ireland
DocuSign Envelope ID: ED8392DF-3DB9-45F8-9BFD-510FAE5AF90D
FB973_EN_A5_v1_20220826.indb 8FB973_EN_A5_v1_20220826.indb 8 2022/8/26 16:062022/8/26 16:06

UK
[phone]
Eire
NL 040 – 2628080
FR 01 60 34 28 80
BE-NL 0800-29129
BE-FR 0800-29229
DE 0800 – 1860806
IT N/A
ES 901-100 133
FB973_EN_A5_v1_20220826.indb 9FB973_EN_A5_v1_20220826.indb 9 2022/8/26 16:062022/8/26 16:06

FB973_EN_A5_v1_20220826.indb 10FB973_EN_A5_v1_20220826.indb 10 2022/8/26 16:062022/8/26 16:06

FB973_EN_A5_v1_20220826.indb 11FB973_EN_A5_v1_20220826.indb 11 2022/8/26 16:062022/8/26 16:06

FB973_EN_A5_v1_2022/08/26
FB973_EN_A5_v1_20220826.indb 12FB973_EN_A5_v1_20220826.indb 12 2022/8/26 16:062022/8/26 16:06