Roxor 1503AUA00031N User manual

SL08_Rev01 Work Instruction Template Template Released 8 November 2018
Work Instruction: Install MTX Sound Bar (Aluminum)
Sound Bar Kit (P/N 1503AUA00031N)
CONFIDENTIALDOCUMENT
© 2020 Mahindra Vehicle Sales and Service, Inc. All Rights Reserved.
ROXOR is a registered trademark of Mahindra Vehicle Sales and Service, Inc.
Page 1 of 3
W O R K I N S TR U C T I O N O V E R V I E W
l DO NOT ATTEMPT THIS PROCEDURE IF YOU DO NOT
HAVE PROPER TOOLS, TRAINING, AND FACILITIES.
l Read and follow all instructions provided when installing
this product. Failure to do so may result in placing
occupants at risk of serious injury or death.
l To protect bystanders and the service technician(s), shut
vehicle off, remove the Ignition Key and secure vehicle to
prevent unintended movement.
l Never operate the vehicle in excess of manufacturer’s
specifications.
l This installation requires a ROPS Harness sold separately;
o
Sound Bar Only use ROPS harness
Part Number - 1801CUA00041N
o
Sound Bar with KC 40" Light Bar use ROPS harness
Part Number - 1801CUA00021N
For assistance installing these ROPS Harnesses -- click here
T O O L S R E Q U I R E D
o10 mm Wrench
o10 mm Socket
o5 mm Allen Wrench
oSocket Wrench
oUtility Knife / Scissors
oProtective Eye-wear
T OR Q U E S P E C I F I C A T I O N
Tighten each fastener to the torque specification below:
lM6 Cap Head Allen Bolts – 6.0 to 6.5 N•m
lM6 Hex Head Shoulder Bolts – 7.5 to 8.0 N•m
K I T
Kit Number - 1503AUA00031N
Kit
Component Description Qty
MTX Sound Bar 1
Mounting Block Assemblies 2
Bar Mounting Clamps 2
Hex Head Shoulder Bolt - M6 2
Flat Washer - M6 2
Hex Flange Nut - M6 2
I N S TA LL A T I O N P R OC E D U R E
1. Remove Hard Top, Soft Cab Enclosure or Bikini Top if
equipped.
2. Connect and route ROPS Sound Bar Harness (Part Number
- 1801CUA00041N) as shown.
For more detail on this step refer to
"Installing ROPS Accessory Harnesses"

SL08_Rev01 Work Instruction Template Template Released 8 November 2018
Work Instruction: Install MTX Sound Bar (Aluminum)
Sound Bar Kit (P/N 1503AUA00031N)
CONFIDENTIALDOCUMENT
© 2020 Mahindra Vehicle Sales and Service, Inc. All Rights Reserved.
ROXOR is a registered trademark of Mahindra Vehicle Sales and Service, Inc.
Page 2 of 3
3. If installing with a Bikini Top, position (2)bar clamps inward
of hook and loop flaps on Bikini Top. No modification are
required for Hard Top and Soft Cab Enclosure.
4. Install (2) supplied Mounting Blocks with a 5 mm Allen
wrench, position 3" (76.2 mm) from each end. For Bikini Top
only, position at 6.75" (171.5 mm) from each end.
5. Mark center of ROPS B-Pillar Cross Bar.
6. Roughly position Mounting Clamps in both directions from
center mark.
7. Hang Sound Bar on (2) Bar Mounting Clamps using (2) Hex
Head Shoulder Bolts.
8. Install (2) flat washers and (2) flange nuts, then tighten just
enough to allow for Sound Bar angle adjustments.
9. Adjust angle of Sound Bar. Do not angle more than 40° if
installing with a Soft Cab Enclosure. This is to prevent
interference with Rear Bow Assembly.
10. Torque (2) M6 fasteners to specifications.

SL08_Rev01 Work Instruction Template Template Released 8 November 2018
Work Instruction: Install MTX Sound Bar (Aluminum)
Sound Bar Kit (P/N 1503AUA00031N)
CONFIDENTIALDOCUMENT
© 2020 Mahindra Vehicle Sales and Service, Inc. All Rights Reserved.
ROXOR is a registered trademark of Mahindra Vehicle Sales and Service, Inc.
Page 3 of 3
11. Connect MTX Sound Bar pigtail to ROPSSound Bar
Harness.
12. Follow MTX Audio Owner's Manual for tips on set-up and
use.