Royal Enfield Himalayan Series User manual

© 2018 Royal Enfield
1
*HQXLQH0RWRUF\FOH$FFHVVRU\,QVWUXFWLRQV
Aluminium Pannier Kit
Part Number:
1990200, 1990227, 1990230, 1990232, 1990243
Models :
Himalayan
WARNING: Royal Enfield genuine accessories are designed to fit only the specific Royal Enfield motorcycle(s) that
are specified above. They should not be fitted to any other type of motorcycle. Pay particular attention to the
warnings and cautions contained in this instruction, failure to do so may result in an incorrect installation of the accessory
which could result in an unsafe riding condition and possible accident. If in any doubt always seek the help from your
authorised Royal Enfield dealer.
WARNING: Before starting any accessory kit installation ensure the motorcycle is supported in a stable condition.
Failure to support the motorcycle correctly could lead to motorcycle damage or personal injury.
WARNING: All fixings must be tightened to the torque values specified in this instruction. Failure to tighten
fixings to the correct torque could result in an unsafe riding condition and possible accident.
CAUTION:Care should be taken when fitting any accessory kit. Incorrect handling kit components or the use of incorrect
tools could lead to component or motorcycle damage.
NOTE:The content of this instruction is subject to change at any time without notice or liability. Royal Enfield reserves the right to
revise the information presented at any time.














 


Instruction No. KXL00026 - Issue B
Item Description Qty
1Pannier, right hand 1
2Pannier, left hand 1
3Pannier rail, right hand 1
4Pannier rail, left hand 1
5Connector bar 1
Item Description Qty
6Extension harness (red connectors) 1
7Extension harness (green connectors) 1
8Fixing, M8 x 45mm 2
9Fixing, M8 x 60mm 4
10 Fixing, M6x15mm 4
11 Washer, M8 4

© 2018 Royal Enfield 2
Installing the Pannier Rails
1Remove the rider and pillion seats, as described in the Owner’s
Handbook.
2Disconnect the battery, negative lead first.
3Remove infill panel and numberplate hanger rear fixings (1) from
the underside of the rear mudguard. Retain the fixings for reuse.
While supporting the infill panel and numberplate hanger (2) remove
the two front fixings (3). Retain the fixings (3), washers (4) and
rubber sleeves (5) for reuse.
4Carefully lower the infill panel and number plate hanger from the
underside of the rear mudguard and disconnect the numberplate
light harness connector (1) from the main wiring harness connector
(2).
Retain the infill panel and number plate hanger for reuse.


5Disconnect the right hand indicator harness (GREEN) (1) and left
hand indicator harness (RED) (2) from the main wiring harness (3).
6Remove the left hand and right hand rear indicators. Retain the
indicators (1), fixings (2) and nuts (3) for reuse.











Instruction No. KXL00026 - Issue B

© 2018 Royal Enfield
3
7Remove the right hand front luggage rack fixing (1). Retain the
fixing for future reuse if the accessory pannier kit is removed.
Remove the right hand rear saddlebag mounting fixing (2). Retain
the fixing for future reuse if the accessory pannier kit is removed.
8Position the right hand pannier rail (1) on the motorcycle ensuring
the top rear mounting (2) is correctly located in the luggage rack
mounting recess (3), as shown.
Align the pannier rail front mounting (4) with the fixing position on
the motorcycle frame (5) and loosely fit an M8 x 45mm fixing (6) and
M8 washer (7) from the kit.







9Loosely fit an M8 x 60mm fixing (1) from the kit to the pannier rail
luggage rack mounting position (2).
Loosely fit an M8 x 60mm fixing (3) and M8 washer (4) from the kit
to the pannier rail and saddlebag mounting position (5), as shown.
Do not fully tighten any pannier rail fixings at this stage.
Repeat steps 7 to 9 for the left hand pannier rail.
10 Loosen the grab rail (1) rear fixings (2) . Do not remove the
fixings.









Instruction No. KXL00026 - Issue B

© 2018 Royal Enfield 4Instruction No. KXL00026 - Issue B
11 Align the rear connector bar (1) with the fixing positions on the
right hand (2) and left hand (3) pannier rails.
Fit the M6 x 15mm fixings (4) from the kit to secure the connector
bar to the pannier rails.
Do not fully tighten the fixings at this stage.







12 Looking from the rear of the motorcycle ensure the left hand (1)
and right hand (2) pannier rails are centralised on the motorcycle, as
shown.
13 Tighten the pannier rail front fixings (1) to 22 Nm.



14 Tighten the rear connector bar fixings (1) to 10 Nm.





16 Route the right hand indicator harness (1) through the indicator
mounting hole in the right hand side of the connector bar (2), as
shown.
17 Fit the right hand indicator (1) to the right hand side of the
connector bar (2) and secure with the original fixing (3) and nut (4).
Tighten the nut to 5 Nm
.
Repeat steps 12 and 13 for the left hand indicator.




18 Connect the indicator extension harnesses (1) from the kit to the
main wiring harness (2).
NOTE:The extension harness with the GREEN connectors must be
connected to the main harness GREEN connector and the extension
harness with the RED connectors must be connected to the main
harness RED connector.






© 2018 Royal Enfield
5
Instruction No. KXL00026 - Issue B
15 Tighten the grab rail (1) rear fixings (2) to 25 Nm.



© 2018 Royal Enfield 6Instruction No. KXL00026 - Issue B
20 Reconnect the numberplate light harness (1) to the main
wiring harness (2).
21 Refit the infill panel and numberplate hanger (1) to the underside
of the rear mudguard (2) ensuring the indicator harnesses (3) are
routed in the infill panel recesses (4), as shown.
CAUTION:Ensure the re-routed indicator wiring harnesses
are not trapped between the infill panel and rear mudguard.
A wiring harness which becomes trapped during installation can
result in equipment malfunction.





22 Secure the infill panel and numberplate hanger (1) with the
original front fixings (2) and rear fixings (5).
Ensure the front fixings (2), washers (3) and rubber sleeves (4) are
positioned as shown.
Tighten the rear fixings (5) to 5 Nm.
Tighten the front fixings (2) to 10 Nm.
23 Reconnect the battery, positive lead first and check that the
indicators and rear numberplate light function correctly.
24 Refit the rider and pillion seats, as described in the
Owner’s Handbook.









19 Connect the indicator harness extensions (1) to the left hand
indicator harness (2) and right hand indicator harness (3).
NOTE:The extension harness with the GREEN connector must be
connected to the right hand indicator harness and the extension
harness with the RED connector must be connected to the left hand
indicator harness.





© 2018 Royal Enfield
7
Installing the Panniers
1Collect the left hand pannier from the kit. From inside the pannier
(1), loosen the upper mount fixings (2).
2Adjust the position of the upper mount retaining bars (1) until they
are facing towards the bottom of the pannier (2) as shown.



3Position the pannier on the left hand pannier rail (1) ensuring the
lower pannier mounts (2) are located inside the pannier rail (1). Push
the lower pannier mounts (2) onto the pannier rail (1) as shown.
4Position the pannier upper mounts (1) inside the pannier rail (2).
Adjust the position of the pannier upper mount retaining bars (3)
until they are across the pannier rail (2).
CAUTION:Ensure the there is sufficient clearance between
the pannier rail and upper mount retaining bars to prevent
damage to the pannier rail when adjusting the position of the upper
mount retaining bars.
From inside the pannier, tighten the upper mount fixings (4) to
secure the pannier to the pannier rail.
Repeat steps 1 to 4 for the right hand pannier.










Instruction No. KXL00026 - Issue B

© 2018 Royal Enfield 8Instruction No. KXL00026 - Issue B
Pannier Operation
5To open a pannier. Insert the key (1) into the pannier lock and turn
the key to the un-locked position, as shown. Remove the key.
Lift the lock section (2) of the latch to release the latch (3) from the
pannier lid (4).
6To secure a pannier lid in the closed position, ensure the latch (1)
is located on the pannier lid (2) and press the lock section (3) of the
latch down to secure the pannier lid.
Insert the key (4) into the pannier lock and turn the key to the locked
position, as shown. Remove the key.




WARNING: Before riding a motorcycle fitted with accessory panniers always check that the panniers are
securely attached to the pannier rails. Riding a motorcycle with insecure panniers fitted may cause the
motorcycle to become unstable and result in an accident.
WARNING: Panniers must always be fitted to both sides of the motorcycle. Never ride a motorcycle with a
pannier fitted to one side of the motorcycle only. Riding a motorcycle with only one pannier fitted may cause the
motorcycle to become unstable and result in an accident.
WARNING: Never overload the panniers, the maximum safe load for each pannier is 5 Kg. (11 lbs.). Any load
carried should be evenly distributed between both panniers. Incorrect loading of the panniers could cause the
motorcycle to become unstable and result in an accident.
WARNING: The fitment of panniers to the motorcycle will affect the stability and handling of the motorcycle.
Failure to observe the changes in motorcycle stability and handling characteristics could result in an accident.



