Royal Prestige JU0024 Guide

USE & CARE MANUAL
CARE AND USE MANUAL
IMPORTANT: To prevent personal injury and/or property damage,
read and follow the instructions and warnings in this Care and Use Manual.
SAVE THESE INSTRUCTIONS •FOR QUESTIONS OR COMMENTS, SEE REVERSE FOR YOUR SERVICE CENTER CONTACT NUMBER.
FOR HOUSEHOLD USE ONLY.
ROYAL PRESTIGE®JUICER

ROYAL PRESTIGE®
JUICER
2
Table of Contents
Introduction . . . . . . . . . . . . . . . 2
Important Safeguards . . . . . . . . . . . . 3
Product Diagram . . . . . . . . . . . . . 4
Before you Start . . . . . . . . . . . . . 6
Operation . . . . . . . . . . . . . . . 8
Cleaning and Care Instructions. . . . . . . . . . 15
Troubleshooting/FAQ . . . . . . . . . . . . 20
Technical Information . . . . . . . . . . . . 23
Customer Service . . . . . . . . . . . . . 24
READ ALL INSTRUCTIONS BEFORE USE
Introduction
Welcome and congratulations on purchasing your Royal Prestige®Juicer. Please be sure to read this manual in its en-
tirety before using your Royal Prestige®Juicer to ensure that you have an enjoyable experience. The valuable information contained in
this manual will provide an overview of the product, some helpful hints to get you started, as well as trouble-shooting tips should you
have issues with this product in the future.

ROYAL PRESTIGE®
JUICER
3
Important Safeguards
This appliance is for household use only. Please carefully follow the instructions in the manual. (This appliance cannot be covered
under warranty if the product is abnormally or commercially used). Save the instruction manual for future reference. These
instructions are also available on www.royalprestige.com. If the appliance is given away as a gift, please include the manual
with the product.
When using electrical appliances, basic safety precautions should be followed including the following:
READ ALL INSTRUCTIONS.
Risk of
Electric Shock or Fire
• Do not immerse motor base in water or other liquid.
• The use of attachments not recommended or sold by the manufacturer may cause fire, electric
shock or injury.
• Do not spray water or flammable sprays near the appliance.
Risk of Injury • Close supervision is necessary when any appliance is used by or near children.
• Avoid contact with any moving parts.
• Always make sure the feed tube is closed securely in place before motor is turned on. Do not
open the feed tube while Juicer is in operation.
• Turn switch to OFF position aer each use of your Juicer . Make sure the motor stops completely
before disassembling.
• Do not put fingers or other objects into the feed tube during operation. If food becomes lodged,
use pusher or another piece of fruit or vegetable to push it down. When this method does not
work, turn the motor off and disassemble Juicer to remove the remaining food.
• This device is not intended for use by persons (including children) whose physical, sensory or
mental abilities are different or reduced, or who lack experience or knowledge, unless such
persons receive supervision or training for the operation of the device by a person responsible for
your safety.
• Children should be supervised to ensure that they do not use the device as a toy.
Dangers
Related to Misuse
• Unplug from wall outlet when not in use before putting on or taking off parts, and before
cleaning.
• Do not operate any appliance with a damaged cord or plug, or aer the appliance malfunctions or
damaged in any manner. Return appliance to customer support for examination and/or repair.
• Do not use outdoors.
• Do not let cord hang over edge of table, counter, or another surface area.
• Do not use the appliance if the rotation wiper is damaged.
• Do not operate without the pulp cup in place.
• Do not alter or modify the appliance in any way.
• Do not use the appliance for anything other than its intended purpose as described
in the manual.
• The appliance should be used for a limited period of time to prevent overheating.
• Do not use the appliance on an uneven surface.
• Do not put the Juicer parts in the dishwasher or extremely hot water.
• Do not use any hazardous chemicals to clean the appliance.
The following precautions are provided to ensure the safety of the user. Please carefully read through
the precautions and exercise care when using the appliance.
Warning: This label warns of the risk of death or severe injuries.
Caution: This label warns of the risk of injuries or appliance damage.
Prohibited Do not disassemble
Must take action

ROYAL PRESTIGE®
JUICER
4
76
PARTS
Align the red dots ● on each part and
assemble in the order shown. Once
assembled, turn the drum lid clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and body assembly
Place the drum lid on the juicing bowl.
Align the down arrow ▼on the drum lid
with the OPEN mark on the body and
turn to the CLOSE position.
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
9. Juicing Screw7. Rotation Wiper 8. Strainer
* The products illustrated in this booklet may vary slightly from the actual product. * The products illustrated in this booklet may vary slightly from the actual product.
10. Pusher
+
+
+
+
+
+
Product Diagram
1. Feed Tube
Feed Basket
7. Rotation Wiper 8. Strainer 9. Juicing Screw
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
Feed Tube
5. Body
4. Cap
2. Bowl
3. Pulp Cup 3. Feed 6. Juice Cup
11. Cepillo rotativo
76
PARTS
Align the red dots ● on each part and
assemble in the order shown. Once
assembled, turn the drum lid clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and body assembly
Place the drum lid on the juicing bowl.
Align the down arrow ▼on the drum lid
with the OPEN mark on the body and
turn to the CLOSE position.
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
9. Juicing Screw7. Rotation Wiper 8. Strainer
* The products illustrated in this booklet may vary slightly from the actual product. * The products illustrated in this booklet may vary slightly from the actual product.
10. Pusher
+
+
+
+
+
+
76
PARTS
Align the red dots ● on each part and
assemble in the order shown. Once
assembled, turn the drum lid clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and body assembly
Place the drum lid on the juicing bowl.
Align the down arrow ▼on the drum lid
with the OPEN mark on the body and
turn to the CLOSE position.
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
9. Juicing Screw7. Rotation Wiper 8. Strainer
* The products illustrated in this booklet may vary slightly from the actual product. * The products illustrated in this booklet may vary slightly from the actual product.
10. Pusher
+
+
+
+
+
+
2. Feed Tube locking mechanism
11.

ROYAL PRESTIGE®
JUICER
5
* The products illustrated/photographed in this manual may vary slightly from the actual product.
Align the red dots ●on each part and
assemble all the pieces in the order shown.
Once assembled, turn the feed tube clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and base assembly
Assemble the entire top-set onto the base
ensuring the arrow symbol ▼ on the feed
tube is aligned with the arrow symbol on
the base.
76
PARTS
Align the red dots ● on each part and
assemble in the order shown. Once
assembled, turn the drum lid clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and body assembly
Place the drum lid on the juicing bowl.
Align the down arrow ▼on the drum lid
with the OPEN mark on the body and
turn to the CLOSE position.
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
9. Juicing Screw7. Rotation Wiper 8. Strainer
* The products illustrated in this booklet may vary slightly from the actual product. * The products illustrated in this booklet may vary slightly from the actual product.
10. Pusher
+
+
+
+
+
+

ROYAL PRESTIGE®
JUICER
6
Before You Start
Check Before Operating Wash the parts before first use.
Note: The screw needs to be locked in place
in order to close the feed tube.
STEP 1 Top-set Assembly
Assemble the strainer into the rotation wiper, then
place this assembly into the bowl ensuring the red dot
●on the strainer is aligned with the red
dot ●on the bowl.
Place the screw into the strainer. Turn and press down
on it until it clicks into place.
Place the feed tube onto the bowl aligning the red
dot ●on the feed tube with the red dot ●on the bowl.
Turn clockwise to close, aligning the red dot ●on the
feed tube with the close mark .
1
2
3
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot
●
on the drum lid with
the red dot
●
on the juicing bowl. Turn
clockwise to close, aligning the red dot
●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot
●
on
the strainer is aligned with the red dot
●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close

ROYAL PRESTIGE®
JUICER
7
Note: The Juicer will not operate if parts are not
assembled properly.
STEP 2 Top-set and Base Assembly
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
Open/Close mark on the top-set.
4
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot
●
on the drum lid with
the red dot
●
on the juicing bowl. Turn
clockwise to close, aligning the red dot
●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot
●
on
the strainer is aligned with the red dot
●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
Place the top-set on top of the base. Align the
arrow ▼ on the feed tube with the arrow
(open) on the base.
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
For easy assembly hold the feed tube with
both hands and turn clockwise as shown
in the illustration.
TIP
5
Place the pulp cup under the pulp spout and
place the juice cup under the juice spout as
shown in the illustration. Pusher is optional.
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
6

ROYAL PRESTIGE®
JUICER
8
Operation
STEP 1
After preparing the ingredients, plug the power cord into a wall outlet.
Note: • Do not touch the power cord with wet hands. It may cause electrical shock, short-circuit, or fire.
• Check the safety of the wall outlet.
STEP 2
Press the FORWARD button to operate.
Note: • Forward: Pulls down and slowly presses the ingredients.
• Reverse: Pushes the ingredients back up to dislodge them.
If the ingredients become jammed in the screw and the feed tube does not open, press the OFF button. Then press and
hold the REVERSE button until the ingredients become dislodged. Repeat REVERSE - OFF - FORWARD as often as needed to achieve
the desired result.
REVERSE: Pushes the ingredients back up to dislodge them.
The REVERSE button only works while holding down the switch.
Switch OFF ensuring that the Juicer comes to a complete stop. Then press REVERSE. Hold the REVERSE
button for 2-3 seconds and release. Repeat as needed. Let the Juicer stop completely before using the
REVERSE button to prevent malfunction.
If the Juicer does not work after these steps, disassemble and clean the parts before operating the
Juicer again.
If the Juicer stops during operation
Switch the button to OFF position then press and hold the
REVERSE button until the ingredients become dislodged.
Repeat REVERSE - OFF - FORWARD as needed.
FORWARD : Pulls down the food
OFF : Stops the operation
REVERSE : Pushes the food back up
OFF OFF
▲ ▲ ▲
REVERSE FORWARD

Note |
➊ ➋ ➌ ➍

ROYAL PRESTIGE®
JUICER
9
Insert the prepared ingredients one piece at a time.
• Prepare ingredients for optimal extraction.
• If a large quantity of ingredients is put into the feed tube, it can cause the Juicer to stop.
• Insert the ingredients one piece at a time.
• Remove hard seeds or pits in fruits. When juicing frozen fruits, completely thaw before juicing.
Note:
Tip:
Tip:
STEP 3
Use the cap to make mixed juices, stop juice from dripping,
or rinse between different juices.
After juice and pulp are completely extracted, switch the unit OFF.
• If the remaining ingredients in the bowl have not been extracted completely, the feed tube may not
open easily. Aer each extraction, run the Juicer for an additional 30 seconds to let it extract
the remaining pulp.
• When the feed tube is stuck, press the REVERSE - OFF - FORWARD button in this order; switching back
and forth 2 or 3 times to dislodge the ingredients. Then place hands on top of the feed tube’s lid and
firmly press down, while simultaneously turning it counter clockwise to open.
» Depending on the ingredients, pour water down the feed tube to rinse out the interior
of the bowl and then attempt to remove it.
• Juicing with the cap closed makes various mixed juice creations when different fruits and vegetables,
milk, banana, beans etc. are selected.
• Aer juicing, close the cap to stop the juice from dripping, especially when disassembling the bowl off
the base.
• When making different juices quickly rinse away any leover flavors by running a glass of water in the
Juicer with the cap closed.
• Leave the cap open when juicing ingredients that create excessive foam during
extraction, (e.g. apples, celery).
• Pay close attention when operating with the cap closed. Juice may overflow if the juice collected
in the bowl exceeds its capacity marked on the bowl.
Note:
Note :
Tip:
Cap
STEP 4
STEP 5
• Tough and fibrous ingredients: Cut to size.
• Fibrous leafy vegetables (celery, kale, collard greens, etc.): Cut the stems to size.
Hard vegetables & high fiber foods | (E.g. carrots, beets, & spinach)
• So ingredients: Cut ingredients to size. Insert the prepared ingredients into the feed
basket and push down the ingredient with the basket lid to extract.
So Fruits & Vegetables | (E.g. apples, oranges & tomatoes)
Insert
into the
feed tube
Insert
into the
feed
basket
cap

ROYAL PRESTIGE®
JUICER
10
Helpful Hints
1. Operating the Juicer without ingredients can cause damage to the juicing screw.
2. Do not continuously operate the Juicer for more than 30 minutes.
This can overheat the motor and damage it.
Aer continuous use, let the Juicer rest for 30 minutes to cool down before starting another session.
3. Do not put fingers or other objects into the feed tube. Always use provided pusher when needed.
If other objects are inserted into the feed tube during operation, they can get stuck and damage the Juicer parts and/
or cause injury.
4. Do not put dried or hard ingredients like whole grains, fruits with hard seeds or ice into the Juicer.
These may damage the parts (e.g. bowl, juicing screw, and strainer).
• Beans or grains can be used if soaked overnight or boiled.
• Fruits with pits and hard seeds must be pitted before juicing (e.g. nectarines, peaches, mangoes and cherries).
• When using frozen fruits with small seeds such as grapes, completely thaw before inserting them into
the Juicer .
5. Do not use ingredients containing excessive amounts of vegetable oil or animal fat. Do not use the Juicer to extract
vegetable oil from ingredients.
If vegetable/animal oil gets on the screw, it may reduce performance and even damage the part.
6. Do not reinsert the extracted pulp into the Juicer . This can cause the unit to stop or cause the feed tube not to open.
7. Aer juicing ingredients with seeds like grapes, thoroughly clean all the crevices on the bottom of the screw.
Juicer damaged due to owner negligence or from not following the instructions in this manual will void the warranty.
Hard seeds Peach, nectarines, apricot, plum, mango, etc.
Remove hard seeds or pits from the ingredients before juicing
Hard or inedible skins Pineapple, melon, mango, orange, etc.
Peel the skin from the ingredients before juicing.
Frozen fruits or ice Frozen strawberry, blueberry, raspberry, etc.
Completely thaw frozen fruits before juicing. Do not use ice.
DO NOT put the following ingredients into the Juicer:

ROYAL PRESTIGE®
JUICER
11
Vegetable/animal oil Sesame seed, butter, margarine, etc.
Do not extract ingredients containing vegetable or animal oil. This can reduce
performance and even damage the Juicer .
Others Coconut, sugarcane, whole grains, etc.
Do not extract ingredients with no water content.
Experience the best quality juice by understanding each ingredient’s characteristics and knowing the optimal
way of handling them.
The Juicer is an innovative product that uses a patented slow-speed juicing technology to efficiently extract the juice from ingredients.
The Juicer is designed to obtain the best result from ingredients with firm composition and with high water content. For best
result, each ingredient should be prepared and extracted depending on its characteristics
and properties.
Tips On Ingredients
Before Operating
• Before Operating: If the Juicer is jammed or if the feed tube does not
open, press the REVERSE button and hold until the ingredient becomes dislodged. Repeat
REVERSE-OFF-FORWARD as needed.
• Continue operating the Juicer until all the ingredients in the bowl
are extracted. The feed tube may not open easily if there is a lot of pulp remaining
in the Juicer .
• Every ingredient yields different amounts of juice.
Juice Yield
• For the optimal extraction and maximum juice yield, cut the ingredients following the
guidelines given in this section.
• Insert ingredients slowly, monitoring how they are extracted. The juice yield may
vary depending on the juicing speed.
Adjusting
the Amount
of Pulp in the Juice
• Depending on the ingredient, you may get extra pulp when juicing continuously.
• To reduce the amount of pulp, disassemble the top-set and wash frequently.

ROYAL PRESTIGE®
JUICER
12
SOFT FRUITS AND VEGETABLES (e.g. oranges, tomatoes):
PREPARATION TIPS:
• Cut ingredients cut to size.
EXTRACTION TIPS:
• Slowly insert the ingredients, one piece at a time.
• Use the pusher to push the ingredients down the feed tube. (The pusher also helps prevent juice from spraying out
of the feed tube when extracting ingredients with high water content)
• Leave the cap open when juicing ingredients that create excessive foam during extraction, like apples and
celery. (Foam can accumulate if operated with the cap closed).
• It is recommended that the extracted juice be consumed within 48 hours aer extracting. Depending on the
density of the ingredients, the extracted juice can gradually separate into layers over time.
• If there is an excessive amount of foam, use a mesh strainer to separate it from the juice.
• When an ingredient is being juiced by the screw, the squeezed ingredient may splash juice through the
feed tube. Use the pusher to block splashing while juicing.
HARD FRUITS AND VEGETABLES (e.g. carrots, potatoes, beets):
PREPARATION TIPS:
• Slice the ingredients cut to size
• Peel the skin off oranges, and for tomatoes and apples, take out the stem.
• If the ingredients are larger than the feed tube, cut the ingredients into pieces that will fit into it.
• Fruits with seeds must be pitted before extraction. Cut to size then slowly insert them down the feed tube.
• Hard fruits and vegetables may put excess strain onto the motor and cause it to stall.
• To increase the juice yield, juice fruits and vegetables with high water content.

ROYAL PRESTIGE®
JUICER
13
EXTRACTION TIPS:
• Slowly insert the ingredients, one at a time.
• Pace the juicing speed, ensuring each ingredient is thoroughly extracted.
• To maximize the juice yield, juice ingredients with high water content.
INGREDIENTS WITH SMALL SEEDS (e.g. raspberry, pomegranate, grape):
Slowly insert ingredients with small seeds to prevent clogging the Strainer.
PREPARATION TIPS:
• When juicing frozen ingredients, make sure they are completely thawed (e.g. raspberry, strawberry).
• Rinse ingredients thoroughly. Remove all stems.
• For pomegranate, discard the skin and juice only the inner part.
EXTRACTION TIPS:
• Depending on the size of the grape, insert 3-5 grapes at a time while monitoring the extraction result.
• For ingredients like pomegranate and raspberry, insert about 1 tablespoon (5g) at a time.
• Frozen ingredients usually lose a significant amount of fluid from thawing. When juicing, mix milk or yogurt to
balance the fluid lost.
• Insert ingredients slowly to minimize the amount of leftover seeds in the Strainer.
• For best results, use ingredients with a higher amount of fluid (e.g. apple, pear).
CAUTION:
If the feed tube does not open due to excessive amount of small seeds left in the bowl, continuously run the Juicer
for 30 seconds to extract any leftover seeds. If the feed tube is still stuck, repeat REVERSE - OFF- FORWARD
until the ingredients become dislodged. Then twist the feed tube to open while pushing downwards with palms.
(Depending on the ingredient, pour some water down the feed tube for a quick rinse to help dislodge).

ROYAL PRESTIGE®
JUICER
14
CAUTION:
• The fibers from tough ingredients like celery can wrap around the juicing screw and affect the Juicer ’s
performance. Cut the stems to size.
• Foam can build up from juicing fibrous ingredients. Use strainer to remove the foam before serving.
• For ingredients like pineapple, slice off the rind of the pineapple and cut around the fibrous core. Cut the
flesh of the pineapple to smaller pieces.
• Recommended amount of juicing per session is 500g (approximately 2¼ cups). When juicing more than this
amount, wash the top-set before continuing to juice.
FIBROUS AND/OR TOUGH LEAFY INGREDIENTS (e.g. celery, kale, pineapple):
Fibrous ingredients like celery and kale should be cut to size.
PREPARATION TIPS:
• Separate each stem. Cut outer stems to size.
EXTRACTION TIPS:
• Slowly insert the prepared ingredients one at a time.
• Insert more ingredients aer the previous ones have been completely extracted.
■ Roll leaves in spiral before inserting into the Juicer .
■ Insert the leafy part of the ingredients first, then alternate between leafy parts and stems.
■ For ingredients like cilantro or wheatgrass, grab a handful and insert in a bundle.
• When juicing leafy ingredients like celery and kale, do not collect more than 500g (approximately 2¼ cups)
per session. For best results, disassemble and wash the top-set before juicing again.
• If leafy ingredients wrap around the screw, open the feed tube and remove the fibers before
continuing to juice.
• It’s best to use ingredients with a higher amount of fluid, like apples or carrots.

ROYAL PRESTIGE®
JUICER
15
NOTE:
Extract all the remaining pulp in the bowl before stopping the Juicer .
For easier clean up, operate the Juicer for an additional 30 seconds after the juice
is extracted.
When the feed tube is stuck, press the REVERSE – OFF – FORWARD button in this order, switching back
and forth 2 to 3 times to dislodge. Then place hands on the lower part of the feed tube and firmly press down
simultaneously turning the feed tube counter clockwise to open.
NOTE:
When moving the appliance, do not lift
by grabbing the feed tube. Always lift the
appliance by grabbing the base or handle.
Switch OFF and unplug the power cord from
the wall outlet.
1
Turn the feed tube counter clockwise to open.
2
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
Lift top set vertically off base.
3
Remove the juicing screw, strainer and rotation wiper unit
from the bowl. Clean with provided brush.
4
Cleaning and Care

ROYAL PRESTIGE®
JUICER
16
NOTE:
Immediately clean the Juicer after each use.
If remaining residue in the Juicer dries up,
it can make disassembling and clean-up
difficult. The excess buildup can cause poor
performance in future uses.
For easier disassembly, place the Top-set in the
sink and run water through it.
Thoroughly dry the bottom of the screw where it
connects to the metal cylinder shaft on the Base.
TIP:
Thoroughly clean the screw, ensuring that it is clean without any residue.
Completely dry before using.
NOTE:
After juicing ingredients with seeds, make sure to thoroughly clean the bottom crevice of the
screw. If this area isn’t properly cleaned, it can affect the balance between the screw and the
Strainer and damage the parts.
Under running water, clean the outside of the screw with
a dish scrub. Use the tip of a cleaning tool to push out any
residue in the crevices on the bottom of the part.
5
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.

ROYAL PRESTIGE®
JUICER
17
TIP: If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the Juicer .
NOTE: Soak the bowl in a solution of warm water
with baking soda or a little bit of bleach to clean
the excess buildup.
TIP:
It is not necessary to completely clean the Juicer when making multiple juices during
a single juicing session.
When finished juicing, always disassemble and clean thoroughly to prevent residue buildup.
Clean the base with a soft damp towel and dry.
6
With the cap closed, fill the juicing bowl with water and
turn on the Juicer .
Let it run for a moment. Open the cap and let the water
run out of the bowl.
12
Quick Rinsing
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.

ROYAL PRESTIGE®
JUICER
18
How to Clean Silicone Parts
SILICONE BRUSHES
Pull out the Silicone brushes from the rotation wiper to clean.
After cleaning, insert into the slot with the tail pointing down as
shown in the illustration.
SILICONE RING
Remove the silicone ring from the strainer to clean.
After cleaning, push in the silicone ring with the smaller surface
facing down.
Clean the Rotation Wiper under running water. Thoroughly dry after cleaning.
Tip:
2120
HOW TO USE THE CLEANING TOOL
Hold the cleaning tool with one hand and insert
the strainer into the cleaning tool.
HOW TO CLEAN SILICONE PARTS
Silicone Brush
Pull out the silicone brush from
the rotation wiper to clean.
After cleaning, insert into the slot
with the tail pointing down as
shown in the illustration.
Silicone Ring
Remove the silicone ring from
strainer to clean.
After cleaning, push in the silicone
ring.
Smart Cap
Remove from the juice spout
to clean.
After cleaning, attach the smart
cap to the smart cap silicone on
the juice spout.
Clean the rotation wiper under running water.
Thoroughly dry after cleaning. Before assembling the top-set, ensure that the silicone ring is
rmly inserted.
If the silicone ring is not rmly inserted, juice may leak from the bottom of the juicing bowl.
Tip |
Note |
The cleaning tool makes clean-up quick and easy.
Completely dry after cleaning.
Tip |
1
After cleaning, remove the strainer from the
cleaning tool. Dry before storing.
4
Under running water, rotate the cleaning tool
and the strainer in opposite directions to clean.
2
Thoroughly rinse the inside and outside of
the strainer under running water.
3
Note | Insert the strainer until you hear a click.
* The products illustrated in this booklet may vary slightly from the actual product.
Cleaning inside of the bowl
Please unscrew the cover on the bottom and clean inside.
After cleaning, make sure that protrusion part of gear is
placed on the outer part so it ts (connects) with the drum.
Sequence of assembly is in reverse order of disassembly.
CAP
Remove from the juice spout to clean.
After cleaning, insert the silicone piece into the cap and attach
the cap into the juice spout.

ROYAL PRESTIGE®
JUICER
19
How to Use the Rotating Brush
The rotating brush makes clean-up quick and easy. Completely dry after cleaning.
Tip:
Note:
Use the included Cleaning Brush to remove hard-to-reach bits after using the rotating brush.
Thoroughly rinse the inside and outside of the strainer
under running water.
Hold the rotating brush with one hand and insert the
strainer into the brush.
NOTE: Insert the Strainer until you hear a click.
1
Under running water, rotate the rotating brush and the
strainer in opposite directions to clean.
2
3
After cleaning, remove the strainer from the rotating
brush. Dry before storing.
4
2120
HOW TO USE THE CLEANING TOOL
Hold the cleaning tool with one hand and insert
the strainer into the cleaning tool.
HOW TO CLEAN SILICONE PARTS
Silicone Brush
Pull out the silicone brush from
the rotation wiper to clean.
After cleaning, insert into the slot
with the tail pointing down as
shown in the illustration.
Silicone Ring
Remove the silicone ring from
strainer to clean.
After cleaning, push in the silicone
ring.
Smart Cap
Remove from the juice spout
to clean.
After cleaning, attach the smart
cap to the smart cap silicone on
the juice spout.
Clean the rotation wiper under running water.
Thoroughly dry after cleaning. Before assembling the top-set, ensure that the silicone ring is
rmly inserted.
If the silicone ring is not rmly inserted, juice may leak from the bottom of the juicing bowl.
Tip |
Note |
The cleaning tool makes clean-up quick and easy.
Completely dry after cleaning.
Tip |
1
After cleaning, remove the strainer from the
cleaning tool. Dry before storing.
4
Under running water, rotate the cleaning tool
and the strainer in opposite directions to clean.
2
Thoroughly rinse the inside and outside of
the strainer under running water.
3
Note | Insert the strainer until you hear a click.
* The products illustrated in this booklet may vary slightly from the actual product.
Cleaning inside of the bowl
Please unscrew the cover on the bottom and clean inside.
After cleaning, make sure that protrusion part of gear is
placed on the outer part so it ts (connects) with the drum.
Sequence of assembly is in reverse order of disassembly.

ROYAL PRESTIGE®
JUICER
20
Troubleshooting QA
CONDITION REASON SOLUTION
There is no power
to the Juicer
Juicer will not operate if parts are
not assembled properly.
• Check if the power cord is properly plugged in.
• Check if the Feed tube and the bowl are properly
assembled.
• Check to see if the Top-set and the Base are properly
assembled.
Low juice yield Each ingredient has different
amounts of liquid that will yield
different amounts of juice.
If the ingredients are not fresh,
they may contain reduced
amounts of fluid, which will
yield less juice.
• If the ingredient itself has low water content, it may
help to soak it in water before juicing.
• If juicing ingredients with small seeds, aer a few
servings, it may reduce the juice yield. For best
results, disassemble and wash the Top-set in
between juicing.
• If there is seed residue on the bottom of the
Strainer, this can affect Juicer performance and the
overall juice yield.
There is too much pulp
in the juice
When continuously juicing, and
depending on the ingredient, the
juice may contain a lot
of fine pulp.
• To reduce the fine pulp, clean the
Top-set frequently and extract the pulp.
• Use a mesh strainer and put the juice through it to
collect the unwanted pulp.
• If the Strainer and the screw are damaged
and affecting the Juicer ’s performance, it is
recommended the parts be replaced.
• The lifetime of each part may vary depending on
length and method of use and ingredients extracted.
To order parts, see customer service information
on page 24.
• If too many ingredients are inserted at the same
time, it may cause the Juicer to stop frequently. This
can lead to pulpy juice. Insert the ingredients slowly.