RPB RADEX AIRLINE FILTER User manual

INSTRUCTION MANUAL
RADEX AIRLINE FILTER
®
Employers: Read this manual and the flow control device Instruction
Manual and carry out the Employer Responsibilities (page 8).
Product users: Read this manual and the flow control device
Instruction Manual and follow the Product User Safety Instructions
(page 9).
Manuals are regularly updated. Make sure the most recent version of
manual is available to all users for reference.
Current version of manual and other languages: www.rpbsafety.com/
product/radex-airline-filter/#radex-airline-filter
Protecting you for Life’s best moments®

2
RADEX AIRLINE FILTER
EXPLANATION OF SIGNAL WORDS AND SYMBOLS 2
INTRODUCTION 3
IMPORTANT SAFETY INFORMATION
PROTECTION PROVIDED AND LIMITATIONS 4
AIR SOURCE, FITTINGS, AND PRESSURE 5
EMPLOYER RESPONSIBILITIES 8
PRODUCT USER SAFETY INSTRUCTIONS 9
SETUP AND CARE 10
PARTS AND ACCESSORIES 18
WARRANTY AND LIABILITY STATEMENT 20
CONTENTS
RPB®Safety LLC is an ISO9001 certified company.
The following signal word and safety symbols are used in this manual and product labeling:
WARNING indicates a hazardous situation that, if not avoided, could
result in death or serious injury.
DANGER Indicates a hazardous situation that, if not avoided, will result
in death or serious injury.
Read the Instruction Manual.
Additional copies of RPB®manuals can be found at www.rpbsafety.com.
EXPLANATION OF SIGNAL WORDS AND SYMBOLS
WARNING
DANGER

3
RPB®SAFETY - GLOBAL HEADQUARTERS
2807 Samoset Rd, Royal Oak, MI 48073, USA.
T: 1-866-494-4599 F: 1-866-494-4509 E: [e-mail] rpbsafety.com
RPB®SAFETY - APAC
1 Ivan Jamieson Place, Christchurch Airport, Christchurch 8053 New Zealand.
T: [phone] F: [phone] E: [e-mail] rpbsafety.com
RPB®SAFETY - EMEA
Unit 2, Teardrop Industrial Park, London Road, Swanley, BR8 8TS, United Kingdom
T: [phone] E: [e-mail] rpbsafety.com
Copyright ©2019 RPB Safety, LLC. All rights reserved. All materials contained on this
website are protected by United States copyright law and may not be reproduced, distributed,
transmitted, displayed, published or broadcast without the prior written permission of RPB
Safety, LLC. You may not alter or remove any trademark, copyright or other notice from
copies of the content.
All trademarks, service marks, and logos used in this publication, both registered and
unregistered, are the trademarks, service marks, or logos of their respective owners. All
rights in the RPB Intellectual Property contained in this publication, including copyright,
trademarks, service marks, trade secret, and patent rights are reserved. RPB Intellectual
Property means any patent, patented articles, patent applications, designs, industrial designs,
copyrights, software, source code, database rights, moral rights, inventions, techniques,
technical data, trade secrets, know-how, brands, trademarks, trade names, slogans, logos,
and any other common law and proprietary rights, whether registered or unregistered
anywhere in the world, that are owned by, developed in whole or in part by, or licensed by
RPB Safety, LLC.
For technical assistance contact our Customer Service Department at 1-866-494-4599 or
email: [e-mail]
Form #: 62
Rev: 10
INTRODUCTION
The RPB®Radex®Filter System is designed to filter compressed breathing air to remove most
contaminants from the breathing air in supplied air respirator assemblies. Features such as
advanced filter cartridges and the optional micro mist filter will make breathing better and help
protect you for life’s best moments.
This product must be inspected and maintained in accordance with this instruction manual at all
times.
See PROTECTION PROVIDED AND LIMITATIONS (page 4) for details.

4
RADEX AIRLINE FILTER
PROTECTIONS PROVIDED
The RPB®Radex® filter has 6 stages of filter media to help protect the user from solid or liquid
particulates, such as dusts, mists, or odors 0.5 micron or larger, as well as an optional micro mist
filter and mainline prefilter.
LIMITATIONS
The Radex®Airline Filter Part No. 04-900 does not remove Carbon Monoxide and other toxic
gases/fumes from the compressed air.
HAZARD LIMITATIONS
The RPB®Radex®is NOT FOR USE if the air source being supplied to the Radex®has any of
these conditions:
The air source atmosphere contains less than 19.5% oxygen.
The air source contains hazardous gases (e.g., carbon monoxide).
The temperature is outside the range of 14°F to 140°F (-10°C to +60°C).
STANDARDS AND REGULATIONS
The Radex®Filtration system can help meet requirements for breathing air quality. Refer to
the following standards and regulations, depending on the location the Radex®is being used,
for more information:
ANSI/Compressed Gas Association Commodity Specification for Air, G-7.1-1989.
PROTECTION PROVIDED AND LIMITATIONS
Improper selection, use, or maintenance of respiratory protection
products can result in injury; life threatening delayed lung, skin or eye
disease; or death. This product is intended for occupational use in accordance with applicable
standards or regulations for your location, industry, and activity (see Employer Responsibilities,
page 8.) Familiarity with standards and regulations related to the use of this protective equipment
is recommended, even if they do not directly apply to you. If self-employed or if used in a non-
occupational setting, refer to Employer Responsibilities and Product User Safety Instructions.
Go to rpbsafety.com/importantsafetyinformation/ for helpful links to OSHA, EN and AS/NZS
standards, and other content.
Employers: Read this manual and the flow control device Instruction Manual and carry out the
Employer Responsibilities (page 8).
Product users: Read this manual and the flow control device Instruction Manual and follow the
Product User Safety Instructions (page 9).
Check website for updates. Product manuals are regularly updated.
Visit www.rpbsafety.com/resources/for the most recent version of this manual before using the
product.
IMPORTANT SAFETY INFORMATION
WARNING

5
AIR SOURCE, FITTINGS, AND PRESSURE
AIR SOURCE
Locate the air source in a clean air environment. Make sure the air source is somewhere that
vehicles, forklifts, and other machinery are not running near the air inlet, as this will cause
carbon monoxide to be drawn into your air supply.
The Air supplied to the Radex®Airline Filter should not exceed 140 degrees Fahrenheit (60
degrees Celsius). When an oil lubricated air compressor is used and it gets excessively hot, it
can potentially create Carbon Monoxide.
Do not connect the Radex®’s air supply hose to nitrogen, toxic gases,
inert gases or other non-breathable air sources. Check the air source
before using the airline filter. This apparatus is not designed for use with mobile air supply
systems i.e. cylinders or ambient air pumps. Failure to connect the supply hose to the proper air
source could result in serious injury or death.
ADDITIONAL EQUIPMENT
Always use suitable aftercoolers/dryers. Refer to the compressor manufacturer/instruction
manual for recommendations on setting up the compressor for breathing air and for suitable
in-line air-purifying sorbent beds and filters. The compressor filters and oil level should be
checked daily and changed during regular scheduled maintenance or when contaminated.
REQUIRED AIR QUALITY MONITORING
Air quality must be tested at the time of initial setup from the point of attachment (the
Radex®Airline Filter outlet to the respirator).
Breathing air quality should continuously monitored and/or be tested for at least the
following air components (check your local standards for requirements, see page 4):
O2 - Oxygen
CO2 - Carbon Dioxide
CO - Carbon Monoxide
H2O - Water (Moisture Content)
Hydrocarbons (Oil Mist)
Total Particulates
Retesting the air quality is recommended If the compressor is moved or should the
compressor location or environment significantly change.
DANGER
Federal OSHA 29 CFR 1910.134 “Compressor Operations for Breathing Air”
Army Corps of Engineers EM385-1-1, Section 30.F.04.
EN 12021 :2014 Respiratory equipment. Compressed gases for breathing apparatus.
AS/NZS 1715:2009 Selection, use and maintenance of respiratory protective equipment.

6
RADEX AIRLINE FILTER
A GX4®Gas Monitor, Part No. 08-400, is recommended to monitor Carbon Monoxide,
Oxygen, and Hydrogen Sulfide. (Other gas sensors may become available in the future.)
This can help a system comply with OSHA regulation 1910.134(i)(7), EN 12021, and AS/NZS
1715.
BREATHING AIR PRESSURE
The air pressure must be continually monitored at the point of attachment. Air pressure
must be read from a reliable pressure gauge, while the respirator has air flowing through it,
as required by applicable standards and regulations. Refer to the instruction manual for the
respirator for the Breathing Air Pressure Table to determine the correct air pressure settings
for your setup.
The air pressure supplied to the Radex®Airline Filter should not
exceed 125 psi (8.6 Bar). Exceeding this air pressure could cause the
regulator to not allow enough air into the unit to work properly or cause the unit to explode.
AIR SOURCE, FITTINGS, AND PRESSURE CONTINUED
WARNING

7
TYPICAL SUPPLIED AIR SYSTEM
FIGURE 1.1
9. RESPIRATOR
HEADTOP
ASSEMBLY
(NOVA 3®SHOWN)
8. BREATHING
TUBE ASSEMBLY
AND FLOW
CONTROL
DEVICE
7. B R E AT H I N G
AIR LINE
4. RADEX®AIRLINE
FILTRATION
SYSTEM
5. GX4®GAS
MONITOR
1. SUPPLIED AIR
COMPRESSOR
2. SUPPLIED AIR
LINE TO FILTER
6. POINT OF
ATTACHMENT
6. REGUL ATOR
AND PRESSURE
GAUGE TO
RESPIRATOR
3. OPTIONAL
PREFILTERS AND
REGUL ATOR

8
RADEX AIRLINE FILTER
EMPLOYER RESPONSIBILITIES
Your specific responsibilities may vary by location and industry, but in general RPB®expects that
employers will:
Follow all applicable standards and regulations for your location, industry, and activity.
Depending on your location and industry, a number of standards and regulations may apply
to your selection and use of respirators and other personal protective equipment. There also
may be requirements specific to particular contaminants, e.g. silica (see rpbsafety.com/
importantsafetyinformation/ for more information), asbestos, organic pathogens, etc. Know
which requirements apply to your location and industry.
Have appropriate safety programs in place.
Have and follow:
 A workplace safety program.
A written respiratory protection program may be required in accordance with applicable
standards and regulations.
In accordance with the above,
Perform a hazard analysis and select appropriate equipment for each activity. A
hazard analysis should be performed by a qualified person. Controls should be in
place as appropriate and a qualified person should determine what kind of respiratory,
face and eye, head, and hearing protection is appropriate for the intended activities
and environments of use. (For example, select a respirator appropriate to the specific
airborne hazards, with consideration of workplace and user factors and with an Assigned
Protection Factor (APF) that meets or exceeds the required level for employee protection,
select welding face and eye protection appropriate to the type of welding to be done, etc.)
As applicable, check your workplace safety program, respiratory protection program, and
standards and regulations for your activity or industry for related protection requirements,
and see this manual (Protection Provided and Limitations, page 4), the flow control
device, and the respirator head-top Instruction Manual for product specifications.
Be sure employees are medically qualified to use a respirator.
Have a qualified physician or other licensed health care professional (PLHCP) perform
medical evaluations using a medical questionnaire or an initial medical examination per
OSHA 29 CFR 1910.134, EN 12021, AS/NZS 1715 or local standards as required.
Train employees in the Radex®’s use, maintenance, and limitations.
Appoint a qualified individual who is knowledgable about the RPB®Radex® per local
standards as required to provide training:
Ex.: ANSI/ASSE Z88.2 Section 8.1 Qualifications of the Respirator Trainer. Anyone
providing respirator training shall:
a) be knowledgable in the application and use of the respirator(s);
b) have practical knowledge in the selection and use of respirator(s) and work
practices at the site;
c) have an understanding of the site’s respirator program; and
d) be knowledgable of applicable regulations.

9
PRODUCT USER SAFETY INSTRUCTIONS
BEFORE INITIAL USE - BE TRAINED
Do not use this airline filter until you have read this manual, the flow control device and respirator
head-top Instruction Manuals (additional copies available at www.rpbsafety.com) and been trained
in the respirator’s use, maintenance, and limitations by a qualified individual (appointed by your
employer) who is knowledgable about the RPB®Radex®.
MAKE SURE THE SYSTEM IS READY FOR USE
Inspect all components daily for signs of damage or wear and tear that may reduce the level of
protection originally provided. Remove any damaged component or product, as the filter is a
pressure vessel and damage to the vessel could cause fatigue that could result in serious
injury or death. Do not attempt to weld the filter unit.
Make sure that the filter is correctly assembled in the configuration that suits your application.
Never use the filter without all components in place. Verify that you have all required components
for the Radex®airline filter system, such as: pressure relief valve, regulator, drain valve, filter
canister and the lid is tightened securely. Air will be released when pressure in the filter
exceeds 150 psig (10.3 Bar). If the hole is plugged with something other than the pressure
relief valve, excess pressure could cause the vessel to explode, potentially resulting in
serious injury.
Train each Radex®user in the product’s use, application, inspection, maintenance,
storage, and limitations in accordance with the content of this Instruction Manual and the
approved flow control device and respirator head-top Instruction Manuals and standard or
regulatory requirements. Ensure that each intended user reads all of these manuals.
Ensure that equipment is properly set up, used, and maintained.
Make sure that equipment is properly set up, inspected, used, and maintained, including
changing the air filter cartridge per the recommendations in the maintenance section of
this manual.
Measure and monitor airborne contaminants in the work area.
Measure and monitor airborne contaminant levels in the work area in accordance with
applicable requirements.
Make sure the area is ventilated and monitored:
Ventilate and monitor the air in the work area as required by local standards and
regulations.
If you have any questions, contact RPB®.
Call Customer Service Department at:
Tel: [phone]
Email: [e-mail]
Web: rpbsafety.com

10
RADEX AIRLINE FILTER
Use only authentic RPB®brand parts and components. Using incomplete or inappropriate
equipment, including the use of counterfeit or non-RPB®parts, can result in inadequate protection
and could reduce the filtration capabilities. Do not modify or alter any part of this product.
VERIFY THAT YOU HAVE THE APPROPRIATE EQUIPMENT FOR YOUR ACTIVITY
Verify that the Radex®provides appropriate protection for your activity. As applicable, check your
workplace safety program, respiratory protection program, and standards and regulations for your
activity or industry. (See PROTECTION PROVIDED AND LIMITATIONS, page 4.)
BEFORE CONNECTING A RESPIRATOR TO THE RADEX®:
Verify airborne contaminants are within recommended limits for respirator use:
Determine the type and level of contamination. Verify that airborne contaminant
concentrations do not exceed those allowed by applicable regulations and standards for
supplied air respirators.
Make sure the work area is ventilated, and the work area and the breathing air supply are
monitored:
Make sure that the area is well ventilated and that regular air samples are taken to
confirm the atmosphere stays within the levels recommended by OSHA, EN, AS/NZS
and other governing bodies and standards. It is recommended to use a GX4®Gas Monitor
for monitoring breathing air supply coming from the Radex®. Follow the GX4®Gas
Monitor Instruction Manual.
If you have any questions, ask your employer.
SETUP AND CARE
PRODUCT USER SAFETY INSTRUCTIONS CONTINUED
Install the Radex®in a location that is within the recommended temperature range of 14°F to
140°F (-10°C to +60°C) to protect the unit and to keep the air supply below 140°F (60°C). Always
mount the Radex®Airline Filter on a secure level surface. It is recommended to bolt the stand to
the ground to prevent it from tipping over or mount it on a sturdy wall.

11
BASE MOUNT - GROUND
To connect the base mount align the arrows
on the base mount with the arrows on the
filter.
Using the holes in the legs of the base
mount, bolt the unit to the ground,
preferably concrete, to prevent tipping over
and causing injury or damage to the unit.
Use 3/8” (10mm) bolts or lag screws to
secure the base to the ground.
The base mount will only fit in two
positions, the arrows must align before
locking. Turn the filter in a clockwise
direction and lock into position. You will
hear a click when the base is in the final
position.
FIGURE 1.1 FIGURE 1.2
FIGURE 1.3
BASE MOUNT - WALL
The base mount can also be used to mount
the filter to a sturdy wall. Use bolts to
secure the base mount to the wall through
the holes in the legs. Secure the Radex to
the base mount once secured to the wall.
The bolts/screws must be able to hold the
approximate 20lbs. weight of the unit.
FIGURE 1.4

12
RADEX AIRLINE FILTER
04-900 ASSEMBLY - 2 OUTLET MANIFOLD
To assemble the pressure regulator, thread
the pressure gauge into the body and
tighten using an 11mm wrench.
Connect the quick disconnect coupler and
brass cap to the 3/8” tee into the top of the
pressure regulator and tighten. Tighten the
regulator assembly before mounting onto
the Radex®Airline Filter. Use thread sealant
on all fittings.
Fit the complete regulator assembly onto
the top of the Radex®Airline Filter lid using
a 17mm wrench.
Fit the pressure relief valve and tighten.
FIGURE 2.1 FIGURE 2.2
FIGURE 2.3 FIGURE 2.4
The pressure relief valve must be connected to protect the Radex
Airline Filter from over pressurizing. If the hole is plugged with something other than the
pressure relief valve, excess pressure could cause the vessel to explode.
WARNING
SETUP AND CARE CONTINUED

13
04-960 AND 04-964-RZ ASSEMBLY - 6 OUTLET MANIFOLD
To assemble the Six Outlet Manifold, first
thread the 04-915 Pressure Gauge into the
04-965 6 Outlet Manifold and tighten.
Thread all six Couplers into the 04-965
Manifold and tighten.
Thread the completed Six Outlet Manifold
assembly into filter lid and tighten.
FIGURE 3.1 FIGURE 3.2
FIGURE 3.3
FIGURE 3.4
Thread the 04-916 Pressure Relief Valve
into the lid and tighten.

14
RADEX AIRLINE FILTER
OPTIONAL ATTACHMENTS
To fit the Main Line Prefilter, first thread the
reducing nipple 04-926 into the Main Line
Prefilter then thread it into the filter inlet
and tighten, ensure the Main Line Prefilter is
positioned straight. Thread in the 1/2” NPT
Hex Connector 04-952 to the inlet of the
Main Line Prefilter.
FIGURE 4.2
The Micro Mist Filter (04-925), Mainline Prefilter (04-927), Auto Drain Unit (04-924) and
Super High Flow Regulator (04-962) are optional attachments for environments that are
humid or have excessive moisture, or have oil or other fine particulates in the air. They can all
be used together or individually.
To fit the Micro Mist Filter, first thread the
reducing nipple 04-926 into the micro
mist filter then thread it into the filter inlet
and tighten, ensure the micro mist filter is
positioned straight so it drains moisture
from the collection bowl. Thread in the 1/2”
NPT Hex Connector 04-952 to the inlet of
the Micro Mist Filter.
FITTING THE MICRO MIST FILTER
FIGURE 4.1
FITTING THE MAIN LINE PREFILTER
SETUP AND CARE CONTINUED

15
Thread the 04-915 Pressure Gauge and
04-966 1”NPT Connector into the 04-962
Super High Flow Regulator and tighten.
Now thread the complete Regulator into the
INLET port on the body of the Radex®Filter
Unit and tighten or connect it to the inlet of
the Micro Mist Filter or the Main Line Prefilter.
SUPER HIGH FLOW REGULATOR ASSEMBLY
FIGURE 4.5 FIGURE 4.6
To fit the Auto Drain Unit, screw the unit
onto the elbow connector on the draining
valve. Make sure the unit is straight down
so it will drain properly.
FIGURE 4.4
FITTING THE AUTO DRAIN UNIT
To fit the Main Line Prefilter onto the Micro
Mist Filter, thread the 1/2” Hex Connector
04-952 into the Main Line Prefilter then
thread it into the Micro Mist Filter inlet
and tighten, ensure both units positioned
straight.
FIGURE 4.3
FITTING THE MAIN LINE PREFILTER IN LINE
WITH THE MICRO MIST FILTER

16
RADEX AIRLINE FILTER
NOTE
Refer to your respirator instruction manual for pressure ranges for your respirators, increase
the pressure according to the number of operators.
Check that ALL fittings and connections are tight. YOUR FILTER IS NOW READY FOR USE.
INLET CONNECTION
The Radex®Airline Filter has a 1” NPT inlet. Thread in a ball valve close to the inlet so
the unit can be shut off for servicing. Connect inlet fittings and tighten. Once the Radex®is
completely assembled and connected to compressed air open supply line, check fittings for
any air leaks and tighten accordingly.
DO NOT over tighten fittings, as over tightening could crack the
filter body which may lead to an explosion and cause serious injury.
Follow tightening directions from the maintenance section using a torque wrench.
BREATHING AIR SUPPLY HOSES AND FITTINGS
RPB®air supply hoses and fittings must be used between the Radex®(point of attachment)
and the respirator breathing air connection at the wearer’s belt. The hose sections must be
within the correct length and the amount of sections must be within the number specified in
the breathing air pressure table in the instruction manual for the respirator being used. All
connections should be sealed using liquid thread sealant. If the Radex®Airline Filter is hard
piped an isolation valve must be used to enable depressurization for servicing.
MAINTENANCE
Drain Moisture Daily
Water will accumulate in the filter tank, this should be drained by opening the ball valve.
This should be done each day. In very humid climates or if there is large amounts of water in
the air supply it is recommended to leave the ball valve partially open to bleed the moisture.
When fitted with auto drain assembly 04-924, moisture will automatically drain from the unit.
Check it periodically as particles could cause blockages.
Filter cartridge replacement
The filter cartridge should be inspected weekly or more often depending on usage and the
conditions of the air system in which the Radex®Airline Filter is installed. The filter cartridge
should be replaced after a period of 3 months based on a 40 hour week and typical usage.
If the Pressure Gauge on the Super High Flow Regulator and the Pressure Gauge on the
Manifold are reading more than 10psi apart, your cartridge is blocked and needs replacing.
The filter cartridge must be replaced immediately if the following exist:
1. The presence of odor and or tastes in the air being supplied to the respirator.
2. Presence of moisture at the outlet fittings.
3. Large pressure drop of 10psi or more across the filter.
WARNING
SETUP AND CARE CONTINUED

17
Optional Equipment
Check and replace as needed:
Main line pre-filter element.
Micro-mist filter element.
Replacing the Cartridge and Cleaning the unit
1. Shut off the air supply to the Radex®Airline Filter and release all air from the body by
opening the pressure release valve.
Pressurized air in the filter could cause lid to forcefully blow off
during removal, resulting in serious injury.
2. Remove the bolts from the lid and separate the lid from the body.
3. Remove the cartridge and dispose in an appropriate disposal area.
4. Clean and dry the inside of the filter body with water, mild detergent. and a cloth
or paper towels to remove any contaminants, do not clean with volatile chemicals.
Irritation or sickness may result from lack of cleaning the inside of the Radex®housing.
5. Check the o-rings (04-919) and replace if damaged.
6. Insert a new filter cartridge and reassemble the lid, tighten the bolts in the pattern drawn
in (Fig 5.1). Tighten bolts to 10ft/lb torque.
7. Record the data on the sticker supplied with the filter cartridge and place onto the
Radex®Airline Filter body.
FIGURE 5.1
Depending on the contaminants filtered by the Radex®, the used
filter itself may be hazardous. Take appropriate precautions when handling to avoid
exposure to released contaminants; a company disposal procedure may needed.
WARNING
WARNING
PRODUCT CARE
Do not apply paints, solvents, adhesives or
self-adhesive labels except as instructed by
RPB®. This product may be adversely affected
by certain chemicals.

18
RADEX AIRLINE FILTER
1
2
3
11
4
5
7
6
8
10
9
18
12
17
13
14
FIGURE 6.1
PARTS AND ACCESSORIES
16
19
22
28
23
27
26
29
30
15
20
21
31
32
24, 25

19
Item Number Description Part Number
1 RPB®Quick Disconnect Coupler 04-911
Schrader Quick Connect Coupler 03-042-CF
2 3/8” Tee 04-912
3 3/8” Cap 04-913
4 Pressure Regulator 04-914
5 Pressure Gauge (also for 09-962) 04-915
6 Pressure Relief Valve 150 psig (1034 kpa) 04-916
7 3/8” Hex Nipple 04-917
8 Lid 04-918
9 O-ring (set of 2) 04-919
10 Filter Cartridge APF 3100
11 Bolt, Nut, and Washer (set of 4) 04-920
12 Body 04-921
13 Drain Tap 04-922
14 Base Mount 04-923
15 Micro Mist Filter 1/2”* 04-925
16 Micro Mist Filter Element for 04-925* 04-930
17 1” x 1/2” Reducing Nipple* 04-926
18 Main Line Pre Filter* 04-927
19 Filter Element for 04-927* 04-929
20 Brass Elbow* 04-928
21 Auto Drain Unit* 04-924
22 Auto Drain Assembly for 04-924* 04-931
23 Super High Flow Regulator* 04-962
24 Six Outlet Upgrade Kit* inc. 5, 6, 7, 23 04-960
25 Six Outlet RZ Fitting Upgrade Kit* inc. 5, 6, 7, 23 04-964-RZ
26 Six Outlet Filter Lid* 04-961
27 Six Outlet Coupler* 04-964
28 Six Outlet Manifold* 04-965
29 1” NPT Hex Connector* 04-966
30 1” NPT to 3/4” BSP Bushing* 04-967
31 1/2” NPT Hex Connector* 04-952
32 Claw Coupler* 04-951
*Optional parts.
PARTS LIST
Use only exact, authentic RPB®replacement parts (marked
with the RPB®logo and part number), and only in the specified configuration. Using
incomplete or inappropriate equipment, including the use of counterfeit or non-RPB®
parts, can result in inadequate protection and will void the NIOSH approval of the entire
respirator assembly.
WARNING

20
RADEX AIRLINE FILTER
LIMITED WARRANTY
RPB®warrants that its Products will be free from defects in materials and workmanship for one (1)
year, subject to the terms of this limited warranty. The Products are sold only for commercial use,
and no consumer warranties apply to the Products. This limited warranty is for the benefit of the
original Product purchaser, and cannot be transferred or assigned. This is the sole and exclusive
warranty provided by RPB®, and ALL CONDITIONS AND IMPLIED WARRANTIES (INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE EXCLUDED
AND DISCLAIMED FROM WARRANTY COVERAGE. RPB’s®limited warranty coverage does not apply
to damage resulting from accident, improper use or misuse of the Products, wear and tear resulting
from the normal use of the Products, or the failure to properly maintain the Products.
RPB’s®limited warranty coverage runs from the original date of purchase of the Products, and
applies only to warranted defects which first manifest themselves and are reported to RPB®within
the warranty period. RPB®retains the right to determine to its reasonable satisfaction whether any
claimed defect is covered by this limited warranty.
If a warranted defect occurs, RPB®will repair or replace the defective Product (or a component of the
Product), in its sole discretion. This “repair or replacement” remedy is the sole and exclusive remedy
under this limited warranty, and under no circumstances shall RPB’s®liability under this limited
warranty exceed the original purchase price for the Products (or the applicable component). RPB®has
no responsibility for incidental or consequential damages, including loss of use, maintenance and other
costs, and ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE EXCLUDED AND DISCLAIMED
from this limited warranty. Contact RPB®to obtain warranty service. Proof of purchase must be
provided to obtain warranty service. All costs of returning the Products to RPB®for warranty service
must be paid by the purchaser.
RPB®reserves the right to improve its Products through changes in design or materials without being
obligated to purchasers of previously manufactured Products.
LIABILITY
RPB®Safety cannot accept any liability of whatsoever nature arising directly or indirectly from
the use or misuse of RPB®Safety products, including purposes that the products are not designed
for. RPB®Safety is not liable for damage, loss or expense resulting from the failure to give advice
or information or the giving of incorrect advice or information, whether or not due to RPB®
Safety’s negligence or that of its employees, agents or subcontractors.