RPC RPC-WR5441 User manual

Wireless 11N 150Mbps Broadband Router Installation Guide
1
RPC-WR5441
Wireless 802.11b/g/n 150Mbps
AP Router
Installation
Guide

Wireless 11N 150Mbps Broadband Router Installation Guide
2
1. Check your package contents
The following items should be found in your package:
¾Wireless 11N 150Mbps Broadband Router
¾Power adapter
¾Installation Guide
¾CD-Rom
Please make sure that the package contains the above items, if any of the listed items
is damaged or missing, please contact with your distributor.
2. Before you begin
You must have the following at least:
¾Broadband InternetAccess Service(DSL/Cable/Ethernet)
¾10/100Base-T Ethernet card and TCP/IP protocol installed for each PC
¾Internet Explorer 5.0 or higher for Web configuration
¾802.11n , 802.11g or 802.11b compliant wireless adapters (for wireless connection)
3. Hardware Installation
¾Attach one end of the Ethernet cable with RJ-45 connector to your computer’s
Ethernet port, and the other end to one of the LAN ports of your router.
¾Connect the Ethernet cable attaching to your Cable/ADSL modem to the WAN port
of your router.
¾Connect the single DC output connector of the power adapter to the power jack on the
side of the router. Then plug the PowerAdapter into an AC outlet.

Wireless 11N 150Mbps Broadband Router Installation Guide
3
4. LED indicators
LED
Function
SYS
Flashing
Power
on CPU on WLANACT
WPS
working (orange)
WAN
On
WAN Connection normal
Flashing
Data transmitting
LAN
On
LAN Connection normal
Flashing
Data transmitting
5. Login
¾Open a web browser (Safari, Internet Explorer, etc.) on the computer you have just
connected to the router, type http://192.168.1.1 in the address bar, and press enter
¾In the pop-up window, enter the user name guest and password guest and then click
OK
¾Login successfully and the home page appears, the left navigation bar shows the
main options to configure the system, the right screen is the summary information for
viewing the configurations.

Wireless 11N 150Mbps Broadband Router Installation Guide
4
6. System Setup
6.1.Internet connection setting
¾Most connections utilize a dynamic IP (DHCP) and the default is already set to this. If
you have another connection type (like static IP), you will need to click on
‘Convenient Setup’ in the menu and input information given you by your service
provider and then click save.
¾You may already be connected to the Internet. Click on ‘System Information’- ‘Internet
access info’ to see if you have an IP, Gateway, etc (refer to the following picture). If not,
your service provider probably requires you clone the MAC address of your computer to
the router. To do so, click on ‘Internet Setup’ in the menu, then click on ‘Clone MAC
Address’ button to get your computer's MAC address in according to your Internet
connection type, and then click the ‘Save’ button below.
¾If you are still not connected, your modem may actually have the same IP as the
router (192.168.1.1). You will need to change the router's IP. Click on ‘LAN Setup’-
‘LAN IP Address’ and you will see this IP in the main interface. You may edit it to
something different (192.168.2.1 for example). After entering the new IP, click on
‘Save’ below, the router will reboot, and you will need to enter the user name and
password again. Check your system status for IP again, and test connection.
Note: You will need to enter the new IP in the browser to access the user interface for any future setting changes.

Wireless 11N 150Mbps Broadband Router Installation Guide
5
Now you can enjoy your new network. If you have anything related to the questions below,
please refer to the following part
6.2.Advanced setting
6.2.1.Restore to factory setting
If the router ever freezes in a setting change process or if you can’t access it because you can’t
remember the IP you have given it or other problem, you may have to utilize the default button on
the back of the router to put it back to factory settings. You have to press this button for about
1-2 seconds with a pencil when it is working, then leave your hands, it will restore settings
to the factory configuration.
6.2.2. Password modify
You may wish to change the router's password. To do so, click on ‘System Management’-
‘Password setup’, enter a new password and then confirm it.
6.2.3. Firmware upgrade
‘Upgrade’ will give you the option to upgrade the router's firmware if you download a newer
version in the future.
6.2.4. Wireless security setting
To protect your wireless network from unauthorized user access, you need to encrypt your
router. Click ‘Wireless management’- ‘Security’, it supplies “None”, “WEP”, “WPA-PSK”,
“WPA2-PSK”and “WPA/WPA2-PSK” five different encryption modes. But WEP authentication
mode is not recommended when WPS enabled.
If you want to use WEP to encrypt, you can select ASCII characters (alphanumeric format) or
Hexadecimal digits (‘A-F’, ‘a-f’ and ‘0-9’). 64-bit WEP: input 10 Hex values (in the ‘A-F’, ‘a-f’
and ‘0-9’range) or 5 ASCII characters. 128-bit WEP: input 26 Hex values (in the ‘A-F’, ‘a-f’and
‘0-9’ range) or 13 ASCII characters.

Wireless 11N 150Mbps Broadband Router Installation Guide
6
Figure 6-4
If you want to use WPA/ WPA2/ WPA&WPA2 to encrypt, you can select ASCII characters
(alphanumeric format) or Hexadecimal digits (‘A-F’, ‘a-f’and ‘0-9’). No matter what type you
select, input 64 Hex values (in the ‘A-F’, ‘a-f’and ‘0-9’range) or 8-63 ASCII characters.
You can also use WPS to encrypt your network. WPS can connect the wireless adapter and the
router in a safe way. If you have a wireless network card which has WPS button, you may set
up
a
safe network via the following methods
Note: The WPS PIN is on the bottom of the router
Method 1:
¾Push the WPS hardware button of the Router until the orange WPS LED flashes
¾Push the WPS button in the wireless network card for about 3-5 seconds
¾The safe connection will be established automatically, please wait

Wireless 11N 150Mbps Broadband Router Installation Guide
7
Method 2:
¾Check ‘Input PIN from AP’in the wireless adapter’s WI-FI protect setup page, input
PIN of the router, then click ‘PIN Input Config (PIN)’
¾Select this router in the pop-up window, then click ‘Select’
¾The connection will be established automatically.

Wireless 11N 150Mbps Broadband Router Installation Guide
8
RPC-WR5441
Wireless 802.11b/g/n 150Mbps
AP Router
Ghid de instalare

Wireless 11N 150Mbps Broadband Router Installation Guide
9
1. Continutul Pachetului
Inainte sa incepeti sa folositi routerul va rugam verificati daca lipseste ceva din pachet si daca da,
va rugam contactati dealerul dumneavoastra pentru a reclama acest lucru.
¾Broadband router ( 1 buc)
¾Ghid de instalare (1 buc)
¾CD-ROM (1 buc)
¾12V adaptor de putere (1 buc)
¾Cablu Ethernet (1 buc)
2. Inainte de a incepe
Trebuie sa dispuneti de cel putin:
¾Acces in banda larga la internet
¾Placa de retea 10/100
¾Internet Explorer 5.0 sau o versiune superioara pentru configurarile WEB
¾Placa de retea wireless conforma standardelor 802.11n, 802.11g sau 802.11b (pentru
conexiune fara fir)
3. Instalarea Hardware
¾Conectati cablul Ethernet pornind de la portul WAN al routerului la portul LAN al
modemului.
¾Conectati cablul Ethernet primit in cutie intr-un port LAN al routerului si in placa de retea
a calculatorului.
¾Verificati LED-ul LINK al routerului, sa fie aprins, pentru a confirma corectitudinea
conectarii cablurilor.
¾Se conecteaza la transformatorul de tensiune.

Wireless 11N 150Mbps Broadband Router Installation Guide
10
4. Indicatori LED
LED
Functii
SYS
Intermitent
Pornit
WAN
Aprins
Conexiune WAN
normala
Intermitent
Transmite date
LAN
Aprins Conexiune LAN
normala
Intermitent
Transmite date
5. Configurarea Routerului
¾Deschideti un browser web (Internet Explorer, Mozilla, etc.) si introduceti in
campul de adresa IP-ul routerului http://192.168.1.1, apoi apasati „Enter”
¾Fereastra de login va aparea pe ecran. Introduceti “User Name” si “Password”
si apoi click pe butonul “OK” pentru a a loga. User name-ul este “guest” si password
(parola) este “guest”.

Wireless 11N 150Mbps Broadband Router Installation Guide
11
¾Fereastra principala va fi afisata. In bara din stanga va aparea meniul pentru
configurarea routerului, iar in partea dreapta a ecranului veti putea vizualiza setarile
efectuate.
6. Setarea sistemului
6.1. Setari conexiune la internet
¾Cele mai multe conexiuni utilizeaza IP-ul dinamic (DHCP) care este setat implicit. Daca
aveti un alt tip de conexiune (static IP), trebuie sa apasati tasta “Convenient Setup” si sa
introduceti setarile pe care le-ati primit de la furnizorul de internet apoi apasati tasta
“save”.
¾Pentru a verifica daca sunteti deja conectat la internet apasati butonul “System
Information” -> “Internet access info” si veti vedea daca aveti alocat IP, Gateway etc (a
se vedea imaginea de mai jos). Daca nu, furnizorul de internet probabil necesita clonarea
adresei MAC a computerului la router. Pentru a face acest lucru trebuie apasati “Internet
Setup” apoi apasati “Clone Mac Address” si veti obtine adresa MAC a computerului,
apoi apasati “Save” pentru a salva modificarile efectuate.
¾Daca router-ul nu este conectat la internet este posibil ca router-ul sa aiba acelasi IP cu
modemul (192.168.1.1). in acest caz trebuie modificat IP-ul router-ului. Apasati “Lan
Setup”-> “Lan IP Address” si va aparea o interfata unde se va afisa IP-ul router-ului care
se va modifica manual (ex. 192.168.2.1). Dupa ce ati introdus noul IP apasati “Save”,
routerul va reporni si va trebui sa introduceti din nou numele si parola. Verificati din nou
daca este conectat la internet.
Nota: Pentru a accesa meniul router-ului trebuie sa introduceti in Browser noul IP.

Wireless 11N 150Mbps Broadband Router Installation Guide
12
6.2. Setari avansate
6.2.1. Restabilirea setarilor initiale
Daca router-ul se blocheaza in timp ce se efectueaza unele schimbari de setari sau nu va amintiti
adresa IP pentru a accesa meniul router-ului puteti folosi butonul de resetare din spatele routeru-
lui. Tineti apasat acel buton pentru 2-3 secunde in timp ce router-ul este pornit si acesta va
reveni la setarile din fabrica.
6.2.2. Modificarea parolei
Daca doriti sa schimbati parola routeru-lui apasati “System Management”-> “Password setup”
introduceti noua parola apoi confirmati.
6.2.3. Update de firma
Butonul “Upgrade” va da optiunea de a face update la sistemul de operare a routerului, in cazul
in care apare o versiune mai noua.
6.2.4. Securizarea retelei wireless
In cazul care routerul dumneavoastra are si modul wireless este recomandat ca reteaua wireless
pe care o creaza sa fie securizata. Daca nu faceti acest lucru, hackerii si utilizatori nedoriti pot
accesa reteaua si datele, fara acordul dumneavoastra, iar acest lucru va crea probleme mari de
securitate.
Pentru a va proteja de accesari nedorite ale retelei trebuie sa securizati router-ul. Pentru a seta o
parola apasati “Wireless management” -> “Security”. Aici veti intalni patru tipuri diferite de
securitate “WEP”, “WPA-PSK”, “WPA2-PSK”, si “WPA/WPA2-PSK”. Atunci cand optiunea WPS
este activata nu este recomandat sa folositi o encriptare de tipul WEP.
Daca doriti sa folositi criptare de tipul WEP puteti selecta caractere ASCII (format alfa-numeric)
sau Hexadecimal (“A-F”, “a-f”, “0-9”).

Wireless 11N 150Mbps Broadband Router Installation Guide
13
Selectati un tip de criptare WPA. Optiunile disponibile sunt: WPA (TKIP), WPA2 (AES), si WPA2
Mixed. Puteti selecta oricare dintre ele, dar trebuie sa va asigurati ca adaptorul wireless suporta
criptarea respectiva.
Sau puteti selecta o criptare de tipul WPS. Daca aveti un adaptor wireless care foloseste buton
WPS puteti seta o retea securizata folosind metoda urmatoare.
Nota: Pinul WPS este in partea de jos a router-ului
Metoda 1:
¾Apasati butonul WPS care este situat pe router si asteptati ca led-ul sa devina intermitent
¾Tineti apasat butonul WPS de pe cardul de retea timp 3-5 secunde
¾Conexiunea se face automat, va rugam sa asteptati
Metoda 2:
¾Bifati “Input PIN from AP” in setarile cardului de retea, introduceti pinul, apoi apasati “PIN
Iput Config” (PIN)
¾Selectati router-ul din fereastra afisata
¾Conexiunea se va stabili automat