RSG Standby S-PAL06 User manual

USER MANUAL
UNDERCOVER LED KIT
CONTENTS EXTENSION CABLE FLASHER & CABLELIGHTHEAD x 2pcs
FLANGE OPTION x 2pcs
6LED KIT
w/ Split Color
LIGHT ASSEMBLY INSTALLATION
1 inch dia.hole
Lighthead
VEHICLE
CORNER LIGHT
ASSEMBLY
1. Remove the Corner/Head/Tail light from vehicle.
2. Select location to mount lighthead.
3. Drill 1 inch diameter hole to the light assembly.
4. Insert lighthead into hole.
5. Apply silicone (user-supplied) for better fit.
WARNING: Do NOT cover heat sink with silicone. It may cause
damage to the product and void warranty.
NOTE: This unit may not be factory set at FP# 1.
For Flash Pattern change, momentarily apply +VDC
to YELLOW wire: ∙ once for next pattern
∙ quickly three times for reset
2
3
4
5
6
8
9
10
11
12
14
1
Single (split)
Double (split)
Quad (split)
Quint (split)
Mega (split)
Random
Single-Quad (split)
Single H/L(split)
Single (all)
Double (all)
Quad (all)
Ultra (split)
Mega (all)
Ultra (all)
Single-Quad (all)
Single H/L (all)
Steady Half
Quint (all)
7
13
15
16
17
18
Steady All19
Flash Patterns
131220F09
OPERATIONS
NOTE: Lighthead mounting location
may vary depending on the design of
the vehicle light assembly.
to lighthead
To +VDC (fuse @2A) for Color1 activation........................RED
To Chassis Ground.......................................................BLACK
To +VDC (fuse @2A) for Color2 activation...................WHITE
For Synchronization & Flash Patterns.......................YELLOW
Connect YELLOW wires of all Kits together for synchronization
*All kits must be set at the same pattern
For Simultaneous or Split Flash (single head):
1. Apply +VDC to RED and YELLOW wires simultaneously to enter Mode
selection; lighthead will display single flash.
2. Remove YELLOW wire from +VDC and momentarily apply to +VDC to change
Mode: Mode1 = Simultaneous Flash, Color1 and Color2 LEDs flash together.
Mode2 = Split Flash, Color1 LEDs alternate with Color2 LEDs.
(default)
Flash
Patterns
#1~9
Flash
Patterns
#10~17
Flash
Pattern
#18
Color1&2flashtogether,
Head1alternate Head2
Color1&2flashtogether,
Head1&2flash together
SteadyHalf
Mode1 (Simultaneous Flash)
(Suitable for Single-Color Heads) Color1Color2 Color1Color2
1st
Flash
Mode2 (Split Flash)
(Suitable for Split-Color Heads) Color1Color2 Color1Color2
Flash
Patterns
#1~9
Color1 alternate Color2
1st
2nd
1st
2nd
1st
2nd
off off
off off
Flash
Patterns
#10~17
Color1 flash together, off off
off off
Color2 flash together off off
Flash
Pattern
#18
SteadyHalf on on on on
on on
Head1 Head2
on
on
on
on
on
on
on
on
Flash
2nd
1st
2nd
1st
2nd
off
off
off
off
on on on on
on on
Head1 Head2
on
on
on
on on on
on on
offoff offoff
offoff

1. Remove Original Base Plate from lighthead base.
2. Secure Flange Plate to lighthead base with screws.
FLANGE MOUNT INSTALLATION (for kits with Flange option only)
WARNING: Make sure to use the foams when mounting lightheads.
Supplied sheet
metal screw
Lighthead
Wire hole
0.91” (23mm)
1.89” (48mm)
VEHICLE
MOUNTING
SURFACE
to flasher
Mounting
Flange
Foam
Mounting screw holes
Original
Base Plate
Flange
Plate
STROBE
POWER SUPPLY
In this configuration, existing strobe extension cables are used to facilitate installation.
WIRING TO EXISTING STROBE CABLES
STROBE BULB
EXTENSION CABLE
(already in vehicle)
NOTE: Wire colors of LED Kit do not need
to match wire colors of extension cables.
2. Connect LED Kit
connectors to strobe
extension cables.
1. Disconnect strobe
extension cables from
strobe power supply. 3. Remove & Disconnect Strobe
bulbs from extension cables.
4. Insert & Connect LED Ligtheads
to strobe extension cables.
WARNING: Do not connect LED lighthead directly to strobe
power supply. It will cause damage and void the warranty.
to (+)
to GND
CONTROLLER
3. Use mounting flange to mark wire and screws holes to drill.
4. Drill marked holes accordingly.
5. Insert lighthead pigtail into wire hole.
6. Place foam, lighthead, and flange in line with the mounting
holes, and secure with supplied sheet metal screws.