RTA Techni Mobili 2338 User manual

A02 180822
MODEL RTA-2338

50 Lbs
10 Lbs
10 Lbs
Product Size:51 WX23 DX32 H" " "
Drawers Inside Space:
15.5"WX11.5"DX4"H
RTA-2338
4”
30”
16”
32”
11.5”
6.5”
14”
30”
15”
51”
15. 5”
23”

1 2 3
98
8
6
7
5
X2
X1
X1 X6
X1
X1
X1
X1
X1
4
1
1
11
12
13
2
14
17
17
P.3P.3 RTA-2338
Short structure Tall structure
Front horizontal bar
Back horizontal bar
Central bar
Right back
support
Stud Left panel Right panel
PARTS LIST

P.4P.4 RTA-2338
12
X1 X1
10
16
20
17
21
18
22
19
13
11
14 15
X1
X4
X2
X2 X2
X2 X1
X2
X1
X1 X4 (2 Sets)
Grommet
Drawer back panel Drawer bottom panel
Drawer right panel
Drawer Left panelDrawer front panel
Drawer connector
Back guard panel Left guard panel Drawer slider
TabletopBottom panelBack panel

A
B
D
C
PART QTY. ITEM PART QTY. ITEM
E
F
G
H
I
20
4
2
5
8
1
12
16
6X12 MM
6X40 MM
6X30 MM
6X45 MM
6X50 MM
3X15 MM
3X12 MM
14 4X35 MM
66X25 MM
P.5P.5 RTA-2338
SCREWS LIST

P.6P.6 RTA-2338

1
2
3
1
1
77
SCREWS
G
x4
3X15 MM
SCREWS
x4
6X12 MM
B
1
1
5
P.7P.7 RTA-2338
Insert the studs (7) on the bottom of the short structures (1).
First orientate the side panels (8) and (9) with their top sides
away from you and their backs facing each other; then secure
the sliders (15) at the front of the panels using screws(G);
you might need to slide back and forth to find the front hole
thru the opening.
Assemble the Central bar (5) in between the structures (1)
using screws (B) as shown.
98
15
15
TOPTOP BACKBACK
ASSEMBLY STEPS:

4
5
6
9
15
8
15
x4
A
9
8
10
SCREWS
G
x8
3X15 MM
SCREWS
x4
6X25 MM
I
SCREWS
x4
6X40 MM
A
x1
6X25 MM
I
I
9
10
11
8
P.8P.8 RTA-2338
TOPTOP
BACKBACK
Assemble the Side panels (8) and to the Back panel (10)
using bolts (I) as shown and as explained in page 5.
(9)
Assemble the Bottom panel (11) to panels (8), (9) and (10)
using bolts (A) for the sides and bolt (I) for the back, as shown
and as explained in page 5.
ATTENTION:MAKE SURE TO USE THE CORRECT SIZE OF BOLTS AS SHOWN!
Extend the sliders (15) and secure them to the panels (8) and (9)
in the middle and the back using screws (G) as shown.

SCREWS
x5
6X50 MM
E
SCREWS
x4
6X12 MM
B
7
2
4
3
11
1
1
5
P.9P.9 RTA-2338
8
7
With the box assembled in the previous step upside-down,
assemble the structures (1) to the bottom of panel (11) using
screws (E).
Assemble the Horizontal bars (3) and (4) to the Structure (2)
using screws (B) on the side only, then insert the studs (7) on
the bottom of the legs in (2).
PAY ATTENTION TO THE POSITION OF (3) AND (4) AND THE ORIENTATION
OF THEIR BOTTOM HOLES!

9
10
BACK LEG
2
4
3
6
SCREWS
x4
6X12 MM
B
x2
6X45MM
D
SCREWS
A1.
B1.
A2.
B2.
A3.
B3.
4
3
9
P.10P.10 RTA-2338
Using screws (B), secure the Horizontal bars (3) and (4) to the
Structure (2) ON THE INNER HOLES ONLY, as the outer holes
are intended for use until step 13.Also assemble the Support
(6) to the back leg on (2) and the bar (4) as shown.
With the parts assembled in step 7 and 8 upright, assemble
the Horizontal bars (3) and (4) to the Right panel (9) using
screws (D). You might need to align the inserts on panel (9) first.
IF THE SCREW ENTERS ONLY
HALF WAY,CHECK AND ALIGN
THE INSERTS IN THE PANEL AS
SHOWN BELOW.