RTA Techni Mobili RTA-8412L User manual

MODEL RTA-8412L
ASSEMBLY INSTRUCTIONS
Thank you for purchasing our product
REV.042021-1

RTA-8412L P.1P.1
•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.

RTA-8412L P.2P.2
Main Tabletop
x1
B
x1
C
x1
DLeft Interior panel
x1
ERight Exterior panel
x1
F
x1
G
x1
H
Center-Left panel
x2
I
x2
J
x1
K
x1
L
Right Interior panel Center-Right panel
Skirt panel for right cabinet Left-Top Shelf panel Right-Top Shelf panel
x1
ALeft Exterior panel
Skirt panel for left cabinet
x1
M
x1
N
x1
O
x1
P
Right-Bottom Shelf panel Left Adjustable panel Left Horizontal Back panel
Left-Bottom Shelf panel
x1
QRight Horizontal Back panel
x1
RLeft Door
x1
S1 Top Drawer Front panel
x1
S2 Top Drawer Left panel
x1
S3Top Drawer Right panel
x1
S4 Top Drawer Back panel
x1
T1Bottom Drawer Front panel
x1
T2 Bottom Drawer Left panel
x1
T3 Bottom Drawer
Right panel x1
T4 Bottom Drawer
Back panel x2
U
x1
VLeft Vertical Back
panel x1
WRight Vertical
Back panel
Right Tabletop
Drawer Bottom
panel

RTA-8412L
P.3P.3
MAIN PARTS LAYOUT (FOR REFERENCE)
AB
C
D
K
R
GH
Q
PE
F
L
S1
T1
I
J
LIST OF HARDWARE, SCREWS AND FITTINGS
20
14
15
17
16
18
19
1
3
2
4
5
6
7
8
9
10
11
12
PART QTY. ITEM
2Pcs Long Wooden Pin
Cam Lock &
Bolt Sets
16Sets
60Pcs Short Wooden Pin
8Pcs ST5 x 8mm
(Euro Screw)
8Pcs ST4.5 x 13mm
8Pcs ST3 x 16mm
20Pcs ST3.5 x 16mm
10Pcs ST4 x 38mm
27Pcs ST5 x 40mm
16Pcs Cam lock Covers
19Pcs Screw Covers
4Pcs Metal Pin
Handle U Shape
(96mm)
M3.6x22mm Screw
3Sets
2Sets
(4 pcs
per set)
Sliders
Sets
PART QTY. ITEM
Door Hinge
2 Pcs
2Pcs L Bracket
4Pcs Corner Bracket
2Pcs Metal Plate
12Pcs Plactic Feet
13 1Pc Door Stopper
Flat - Right
L - Shape - Right
Flat - Left
L - Shape - Left

P.4RTA-8412L P.4
☛This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the
assembly using this kind of hardware.

RTA-8412L
P.5P.5
%()25(<2867$577+($66(0%/<3/($6(5($'7+()2//2:,1*7,36$1':$51,1*6
❶'RDTXLFNLQYHQWRU\WRPDNH
VXUHWKHSDFNDJHFRQWDLQVDOOWKH
SDUWVDQGKDUGZDUHOLVWHGLQWKH
DVVHPEO\LQVWUXFWLRQV
❷0LVVLQJGDPDJHGDQG
GHIHFWLYHSDUWVFDQEH
UHSODFHGDWQRFRVWWR\RX
3OHDVHUHIHUWRWKHODVW
SDJHVRQWKLVPDQXDO
❹,IGXULQJDVVHPEO\\RX
ILQGDQLVVXHRUQHHG
FODULILFDWLRQSOHDVHFRQWDFW
RXU&XVWRPHU6HUYLFHIRU
DVVLVWDQFH3OHDVHUHIHUWR
WKHODVWSDJHVRQWKLVPDQXDO
❺2QHDFKVWHSUHDGWKH
LQVWUXFWLRQVDQGDQDO\]HWKH
LOOXVWUDWLRQVWKRURXJKO\EHIRUH
SURFHHGLQJWRGRWKHDVVHPEO\
❽'RQRWRYHUWLJKWHQRU
IRUFHWKHVFUHZVDVWKH\
PLJKWEUHDNVWULSGDPDJH
WKHWKUHDGVRIWKHKROHVRU
JHWVWXFNLQVLGHWKHSDUW
❻0DNHVXUH\RX
XQGHUVWDQGZKLFKKDUGZDUH
ZLOOEHXVHGRQHDFKVWHS
8VLQJWKHZURQJVL]HRIVFUHZ
EROWRUSLQPLJKWVWULSWKH
WKUHDGVRUFDXVHGDPDJHWR
WKHSDUWLQZKLFKLWLVEHLQJ
XVHG
❼7RDYRLGPLVDOLJQPHQWV
DOZD\VOHDYHWKHVFUHZV
ORRVHDQGWLJKWHQWKHPXQWLO
DOOSLHFHVDUHSRVLWLRQHG
FRUUHFWO\
❾6RPHWLPHVWKHODPLQDWHPLJKWFRYHUSDUWLDOO\RU
HQWLUHO\WKHKROHRQDSDQHO,IWKHUHLVQRYLVLEOHKROHIRU
WKHVFUHZSDVVDQGSUHVVWKHWLSRI\RXUILQJHURYHUWKH
DUHDZKHUHWKHKROHVKRXOGEHORFDWHGWRIHHOWKH
LQGHQWDWLRQDQGRQFHIRXQGFDUHIXOO\SLHUFHWKH
ODPLQDWHWRUHYHDOWKHKROHXQGHUQHDWK
❿,IWKHKROHVHHPVWRRVPDOOIRUWKHVFUHZILUVWPDNH
VXUH\RXDUHXVLQJWKHFRUUHFWVL]HRIVFUHZDQGWKDWLW¶V
EHHQLQVWDOOHGLQWKHFRUUHFWKROH,IWKHKROHVWLOODSSHDUV
WREHWRRVPDOOFDUHIXOO\SLHUFHWKHODPLQDWHWRUHYHDO
WKHKROH¶VDFWXDOVL]H
❸7KHUHSODFHPHQWSDUWVVHUYLFH
LVOLPLWHGWRWKHFRQWLQHQWDO8QLWHG
6WDWHV,I\RXUHVLGHLQ$ODVND
+DZDLL3XHUWR5LFR
86'HSHQGHQFLHVRURWKHU
FRXQWULHVSOHDVHFRQWDFWWKH
VXSSOLHUIURPZKHUHWKHXQLWZDV
SXUFKDVHG

Install the short dowels 2 into all panels as shown. Use a wooden or light rubber
hammer to avoid damage to the pins. Please pay attention to the correct holes to use as
other holes on the panels are intended for other hardware in other steps.
DO NOT JOIN ANY PANELS, JUST INSTALL THE PINS.
RTA-8412L
P.6P.6
ASSEMBLY STEPS
STEP 1
Hardware/Tools:
260
Pcs
(NOT INCLUDED)
Install the long dowels 1 into the panel A in the holes shown in the illustration.
Please pay attention to the correct holes to use as other holes on the panel are intended
for other hardware in other steps. Then install the door stopper 13 into panel K.
STEP 2
Hardware/Tools:
12
Pcs
2
C
DG H E
F
S2
S3
T2
T3
N
L
K
M
I
I
J
J
P
Q
13 1
Pc
A
1
13
K
Short Dowel
Long Dowel
(NOT INCLUDED)
(Front)
(Front)

Install bolts 3 into panels A, B, S1 and T1 in the holes indicated in the illustration. Please
pay attention to the correct holes to use as other holes on the panels are intended for other
hardware, and attach the metal plates 18 to panel B using screws 7 as shown.
RTA-8412L
P.7P.7
STEP 3
Hardware/Tools:
316
Pcs
(NOT INCLUDED)
Attach the L Bracket 16 to the panels P and Q with screws 7 making sure the corners of
the bracket align with the edge of the panels.
STEP 4
Hardware/Tools:
72
Pcs
74
Pcs
18 2
Pcs
16 2
Pcs
3
7
18
BA
T1
S1
7
16
P
Q
Bolt
ST3.5 x 16
(Front)
(Front)
(Bottom)
(Bottom)
ST3.5 x 16
(NOT INCLUDED)

For each set of slider 20, Separate the pieces according to their shape:
- The Flat shaped will be used in the next step (2 pieces, both left and right).
- The "L" shaped will be used until step 21 (2 pieces, left and right).
RTA-8412L
P.8P.8
STEP 5
Install the flat shaped sliders 20 on panels E and F with screws 4 as shown. For better
results, attach first at the front, then at the back.
STEP 6
Hardware/Tools:
48
Pcs
20 4
Pcs
Flat Shaped
"L" Shaped
Hardware/Tools:
20
2
Sets
Flat - Right
L - Shape - Right
Flat - Left
L - Shape - Left
ST5 x 8
(NOT INCLUDED)
E
(Top)
(Front)
F
(Top)
(Front)
The wheel
goes towards
the front and
facing down.
Attach using these holes, do the front first

Assemble the panel H to panel Q using screw 9 as shown.
RTA-8412L
P.9P.9
STEP 7
Hardware/Tools:
92
Pcs
Assemble the panel E to panel Q using screws 9 as shown.
STEP 8
This illustration shows the
same parts from step 7, but
viewed from a different
angle (from the right).
Q
H
(Bottom)
(Front)
(Top)
Hardware/Tools:
92
Pcs
(NOT INCLUDED)
(Top)
(NOT INCLUDED)
ST5 x 40
ST5 x 40
E
Q

First assemble the panels L and N to panel E using screws 9, then join panels J
to panel E by just pushing the dowels into the holes.
RTA-8412L
P.10P.10
STEP 9
Hardware/Tools:
94
Pcs
First assemble the panel F to panels L and N using screws 9, then install the nail-in
studs 19 to the bottom of the panels E, F and H as shown.
STEP 10
Hardware/Tools:
94
Pcs
(NOT INCLUDED)
This illustration shows the same
parts from step 8, but viewed from
a different angle (from the left).
19 6
Pcs
19
ST5 x 40
ST5 x 40
(NOT INCLUDED)
9
This illustration shows the
same parts from step 9, but
viewed from the right.
E
L
J
N
J
H
F
EL
N

Assemble the panel G to panel P using screw 9 as shown.
RTA-8412L
P.11P.11
STEP 11
Hardware/Tools:
92
Pcs
Assemble the panel D to panel P using screw 9 as shown.
STEP 12
Hardware/Tools:
92
Pcs
This illustration shows the same
parts from step 11, but viewed from
a different angle (from the left).
ST5 x 40
ST5 x 40
(NOT INCLUDED)
(NOT INCLUDED)
NOTE that the big holes for
the cam locks go at the TOP
on panel D
(Top)
(Front)
P
G
(Front)
(Top)
D
P

First assemble the panels K and M to panel D using screws 9, then join panels I to panel
D by just pushing the dowels into the holes.
RTA-8412L
P.12P.12
STEP 13
Hardware/Tools:
94
Pcs
First assemble the panel C to panels K and M using screws 9, then install the
nail-in studs 19 to the bottom of the panels C, D and G as shown.
STEP 14
Hardware/Tools:
94
Pcs
(NOT INCLUDED)
19 6
Pcs
This illustration shows the same
parts from step 12, but viewed from
a different angle (from the right).
ST5 x 40
ST5 x 40
(NOT INCLUDED)
D
K
M
I
I
C
D
K
M
G
This illustration shows the
same parts from step 13, but
viewed from the left.
9
19

3
With the help of another person, bring the sections assembled in steps 10 and 14 upright
and place them oriented as shown. Then assemble panel H to panel G using screws 9.
Then slide the panel V through the grooves of C and D, and W through the grooves of E
and F. Finally, install the metal pins 12 in the desired sets of holes on panels C and D,
and place the panel O over the pins as shown.
RTA-8412L
P.13P.13
STEP 15
Hardware/Tools:
93
Pcs
(NOT INCLUDED)
12 4
Pcs
With the help of another person, place the main panels A and B over the frame, then insert the
cam locks into panels C, D, E, F, G and H, making sure they go in the aligned position, and
turn them to lock the pieces. After the assembly is done, cover the cam locks with caps 10.
STEP 16
Hardware/Tools:
10
Pcs
10 10
Pcs A
B
3
10
C
DE
F
After assembly
ST5 x 40
(NOT INCLUDED)
GH
Alignment
Direction
H
G
O
F
W
E
V
C
D
12 9
This illustration shows the
parts assembled in step
10 and 14 in normal
upright position.

First make sure that the back edge of the tabletop B aligns with the edge of the tabletop A,
then using screws 7, and from underneath the unit, attach:
- The metal plate 18 from B to A.
- The L Brackets 16 from P to A and from Q to B.
RTA-8412L
P.14P.14
From behind the unit, and using screws 6, install the corner brackets 17 on the
positions shown in the illustration.
STEP 18
Hardware/Tools:
68
Pcs
17 4
Pcs
STEP 17
Hardware/Tools:
76
Pcs
7
16
7
18
A
B
P
Q
This illustration shows the parts
same parts from step 17, but viewed
from behind.
17
6
(NOT INCLUDED)
(NOT INCLUDED)
ST3.5 x 16
ST3 x 16

- Using cam locks 3, and as shown and explained in page 4, assemble:
- The side panels S2 and S3 to front panel S1.
- The side panels T2 and T3 to front panel T1.
Then insert the bottom panels U into the grooves of the panels on each drawer as
shown.
RTA-8412L
P.15P.15
Assemble the drawers back panels S4 and T4 to their respective drawers using screws
8 as shown.
STEP 19
Hardware/Tools:
36
Pcs
3
S3 S2
U
U
T3
T2
S1 T1
STEP 20
Hardware/Tools:
810
Pcs
T4 S4
8
ST4 x 38
(NOT INCLUDED)
(NOT INCLUDED)

Place both drawers upside-down and assemble to their bottom the “L” shaped sliders using
screws 7 as shown.
Please note that the wheels go towards the back of the drawers and the sliders should
not protrude from the bottom, otherwise the drawers raise 1” and will not fit in the unit.
RTA-8412L
P.16P.16
On both drawers, install the Handle sets 14 and cover the cam locks with 10 as shown.
STEP 21
Hardware/Tools:
STEP 22
Hardware/Tools:
78
Pcs
20
4
Pcs
77
20
20
10 6
Pcs
14 2
Sets
14
14
10
ST3.5 x 16
(NOT INCLUDED)
(NOT INCLUDED)
VERY IMPORTANT!
INCORRECT:
Raises the
drawer 1”
and won’t fit!
CORRECT:
Sliders don’t
protrude.

Install to the door R the Handle Set 14, and the Hinges 15 with screws 5 as shown.
RTA-8412L
P.17P.17
Place both drawers into the right cabinet as shown, then assemble the door R to the left
cabinet using screws 5, and adjust the alignment if necessary:
A: These screws adjust the vertical alignment.
B: This screw adjusts the horizontal alignment.
C: This screw adjusts the depth.
STEP 23
Hardware/Tools:
STEP 24
54
Pcs
14 1
Set
15 2
Pcs
R
14
14
515
Hardware/Tools:
54
Pcs
R
S1
T1
5
15
ST4.5 x 13
ST4.5 x 13
(NOT INCLUDED)
(NOT INCLUDED)

Cover all the screw heads with caps 11 as shown.
RTA-8412L
P.18P.18
STEP 25
Hardware/Tools:
11 19
Pcs
11
ALL DONE!
Give yourself a nice pat on the back. You did a
great job!

110 Lbs (50Kg ) 110 Lbs (50Kg)
11 Lbs (5Kg)
11 Lbs (5Kg)
11 Lbs (5Kg)
WEIGHT LIMITS
RTA-8412L P.19P.19
AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND
MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then
dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the
tabletops.
•Do not sit on the unit or lean against it.
•Do not allow small children to play under or over the unit.
•Do not allow small children to reach inside the drawers or compartments without your supervision.
•Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by at least 2
persons when moving in the same or adjacent rooms.
•Before moving the unit, make sure to secure or remove any object that is heavy or might fall off, and
be careful handling the right side to avoid separation/damage of panels B (right tabletop) and E (right
back panel).
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
It is recommended to separate the right section (panels B and E) for better handling.
•Shall any part of the unit become defective during the warranty period, replacement parts might be
available to you at no charge. Please refer to the last pages on this manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for
damages or consequences due to accidents, incorrect assembly, negligence, improper use,
modifications, or not heeding the above warnings.
11 Lbs (5Kg)
10 Lbs (4.5Kg)
10 Lbs (4.5Kg)