RTA TECHNI MOBILi RTA-1305 User manual

MODEL RTA-1305
Thanks for purchasing one of our products.
lease read carefully the assembly instructions before the installation.
lease save this manual for future reference.
ASSEMBLY INSTRUCTIONS
P.1 P.1

RTA-1305
P.2 P.2
MAIN ARTS LIST
NOTE: ARTS (1) AND (2)
ARE EXACTLY THE SAME
NOTE: ARTS (3) AND (4)
ARE EXACTLY THE SAME

RTA-1305
P.3 P.3
21
17 14
9
19
15
23
22
9
20
16
Small Stud Large Stud
Wooden in
HARDWARE LIST
ARTS LAYOUT:

RTA-1305
P.4 P.4
☛Do a quick inventory to make sure the product contains all the parts and hardware.
☛Missing, damaged and defective parts can be replaced at no cost to you. Please
refer to the CO TACT and the WARRA TY cards included with the product.
☛If during assembly you find an issue or need clarification, please contact our Customer
Service for assistance. Please refer to the CO TACT card included with the product.
☛On each step read the instructions and analyze the illustrations thoroughly before
proceeding to do the assembly.
☛To avoid misalignments, always leave the screws loose and tighten them until all pieces
are positioned correctly.
☛Do not overtighten or force the screws as they might break, strip, damage the threads
of the holes or get stuck inside the part.
☛Sometimes the laminate might cover partially or entirely the hole on a panel, but the
hole should still be located under the laminate.
☛If there is no visible hole for the screw, pass and press the tip of your finger over the
area where the hole should be located to feel the indentation, and once found, carefully
pierce the laminate to reveal the hole underneath.
☛If the hole seems too small for the screw, first make sure you are using the correct size
of screw and that it’s been installed in the correct hole. If the hole still appears to be too
small, carefully pierce the laminate to reveal the hole’s actual size.
☛This unit uses cam bolts and locks. The following page explains how to work with this
kind of hardware.
☛Make sure you understand which hardware will be used on each step. Using the wrong
size of screw, bolt or pin might cause damage to the part in which it is being used.
⚠BEFORE YOU START THE ASSEMBLY, LEASE READ THE
FOLLOWING TI S AND WARNINGS.

RTA-1305
P.5 P.5
HOW TO ASSEMBLE ARTS USING CAM BOLTS AND CAM LOCKS.
☛This is not an assembly step; it is a guide for when you are
actually doing the assembly using this kind of hardware.
Cam Bolt Cam Lock
1. Screw the bolt into
the corresponding
panel.
2. insert the cam lock in the
hole of the other panel
making sure it is aligned to
engage with the bolt, then
join both panels. ALIGNMENT
DIRECTION
3. The panels might have a
very small gap which is
normal; turn the cam lock
clockwise to lock the parts
together and the gap will
also close.

Assemble the small drawer back panel (6) to the side panels (5) and (7) using
screws (A) as shown.
RTA-1305
P.6 P.6
Insert the drawer bottom panel (8) in between the groves of panels (5), (6)
and (7) as shown.
☛Tip: The laminate might be covering the groves, if this is the case, pierce
first with the tip of a pen or screwdriver.
ER DRAWER

Assemble the drawer front panel (9) to the side panels (5) and (7) using cam
bolts (B) and cam locks (C) as shown and explained in page 5.
RTA-1305
P.7 P.7
Grab all the sliders (1), (2), (3) and (4) and detach the smaller part (b) on all of
them by pressing up or down the lever as shown. Parts (b) will be used on
steps 5 and 9, while parts (a) will be used on step 10.
☛Tip: Make sure the sliders are completely opened, and press hard by the
thickest part of the lever, not the tip.
Please refer to page 5.
REPEAT STEPS 1-3 TO ASSEMBLE
THE SECO D SMALL DRAWER.
ER DRAWER
ER DRAWER

Assemble the rails (1b) and (2b) to the side panels (5) and (7) using screws
(D) as shown.
☛Tip: Both rails are exactly the same.
RTA-1305
P.8 P.8
First assemble the back panel (11) to the left panel (10) using screws (A) as
shown. Then insert the file tubes (13) in between the panels (10) and (12).
Finally, assemble (12) to (11) using screws (A) as shown.
☛Tip: This drawer is for archiving Letter-size files only, but it can also be used
for regular storage if you leave it without the tubes (13).
REPEAT THIS STEP FOR THE
SECO D SMALL DRAWER.
ER DRAWER

Insert the drawer bottom panel (8) in between the groves of panels (10), (11)
and (12) as shown.
☛Tip: The laminate might be covering the groves, and if this is the case,
pierce first with the tip of a pen or screwdriver.
RTA-1305
P.9 P.9
Assemble the drawer front panel (14) to the side panels (10) and (12) using
cam bolts (B) and cam locks (C) as shown and explained in page 5.
Please refer to page 5.

RTA-1305
P.10 P.10
With the panels (15) and (16) positioned as shown, assemble the sliders (1a),
(2a), (3a) and (4a) to the panels using screws (D) EXACTLY as shown.
Assemble the sliders (3b) and (4b) to the side panels (10) and (12) using
screws (D) as shown.
☛Tip: Both rails are exactly the same.
☛Tip: Rails (1a) and (2a) are the same; (3a) and (4a) are also the same.
☛Assembly tip: Open the slider, attach first on the back, then close the slider,
move the ball bearings to the front and screw through the opening as shown.
LEASE NOTE
THE CORRECT
ORIENTATION
OF THE ANELS.
BACK
FRONT