RTA TECHNI MOBILI RTA-2335 User manual

MODEL RTA-2335
MODEL RTA - 2335
Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Please save this manual for future reference.
ASSEMBLY INSTRUCTIONS

RTA-2335

RTA-2335 P.3
PARTS LIST
1
5876
1
4
4
710
16
15
18
23
25
26
27
1
X2
X2
X3
X2
Main Structure
Short Grommet
Side Structure
Connect Tube Connect Panel
43
2
Left Panel Left Support Panel
X4
Studs

RTA-2335 P.4
11 12
13 14
15 16
18 19 20
21 22 23 24
910
25 26
X2X2
X2X2
X2
X2 SETS
Right Panel Left Top Panel Right Top Panel
Back Panel Middle Support Panel
Bottom Panel Glass Top
Slider Left Drawer Front
Panel Drawer Left Panel Drawer Right Panel
Drawer Bottom Panel Drawer Back Panel Right Drawer Front
Panel Hinges
Long Top Panel
Right Support Panel
17
27
Short Top Panel Long Grommet

RTA-2335 P.5
SCREWS LIST
A
C
D
B6X25 MM
16
4
20
PART PARTQTY. QTY.ITEM ITEM
4X35 MM
8
8
3X15 MM
8H
I
J8
E
F
8
1
16
G
6X12 MM
4
6X25 MM
5X40 MM
6X40 MM
3X12 MM
1
Adhesive
Foam Tape

30mm
P.6
RTA-2335

RTA-2335 P.7
ASSEMBLY STEPS:
1
2
18
19
20
23
19
20
21
19
20
21
19
20
22
19
20
22
19
20
3
SCREWS
8PCS
4X35 MM
D
SCREWSSCREWS
4PCS
6X25 MM
B
First screw bolts B to the Left & Right Drawer Front
Panels (18 & 23), then assemble the Drawer Left & Right
Panels (19 & 20) as explained in page 5.
Slide in the Drawer Bottom Panel (21).
Use screws D to assemble the Drawer Back
Panels (22) to the Drawer Left and Right
Panels (19 & 20).

RTA-2335 P.8
4
5
6
3X2
3X2
1
1
1
4
4
5
1
1
5
4
4
SCREWS
4PCS
6X25 MM
C
4PCS
6X12 MM
H
SCREWS
4PCS
6X25 MM
C
4PCS
6X12 MM
H
HC
C
H
Insert the Studs (3) to the Main Structures (1).
Use screws C & H to assemble the Side
Structures (4) and the Connect Tubes (5)
to one of the Main Structures (1).
Use screws C & H to assemble the Side
Structures (4) and the Connect Tubes (5)
to the other Main Structure (1).

RTA-2335 P.9
7
12
98
11
5" 5"
** There are 2 options to assemble our desk, please choose it
according to your preference.
A
B
SCREWSSCREWS
4PCS
6X25 MM
B
First screw bolts B to the Left & Right Top Panels (11 & 12), then assemble
the Left & Right Support Panels (8 & 9) as explained in page 5.
Please pay attention to the direction of panel 8 & 9.
Please follow Step A1-A3, 8-16
Please follow Step B1-B3, 8-16

RTA-2335 P.10
SCREWS
4PCS
3X15 MM
A
13
24 X2
IX2
A1
Use screws A to assemble the Hinges (24) to the Back Panel (13).
Assemble screws I to the Back Panel (13) and Middle Support
Panel (14) as shown.
Please pay attention to the correct position of the parts on both panels.
14
IX2
4PCS
I
811
9
12
14
A2
SCREWSSCREWS
4PCS
6X25 MM
B
First screw bolts B to the other side of the Middle Support Panel (14) as
shown, then assemble the Left & Right Top Panels (11 & 12) as explained
in page 5.
A3
13
6X3
14
Turn the assembled Back Panel (13) upside-down,
insert the Connect Panels (6) between it and the
assembled part in step A2.
FOLLOW STEP 8 - 16 TO FINISH THE DESK.

RTA-2335 P.11
B1
SCREWS
4PCS
3X15 MM
A
Use screws A to assemble the Hinges (24) to the Back Panel (13).
Assemble screws I to the Back Panel (13) and Middle Support
Panel (14) as shown.
Please pay attention to the correct position of the parts on both panels.
4PCS
I
B2
SCREWSSCREWS
4PCS
6X25 MM
B
First screw bolts B to the other side of the Middle Support Panel (14) as
shown, then assemble the Left & Right Top Panels (11 & 12) as explained
in page 5.
B3 Turn the assembled Back Panel (13) upside-down,
insert the Connect Panels (6) between it and the
assembled part in step A2.
FOLLOW STEP 8 - 16 TO FINISH THE DESK.
IX2
IX2
13
14
24 X2
811
9
12
14
13
14
6X3

RTA-2335 P.12
8
9
10
11
12
7
10
8
9
7
10 17
17
13
14
98
10
7
15
SCREWS
16PCS
5X40 MM
E
SCREWS
G
8PCS
3X12 MM
17
SCREWSSCREWS
8PCS
6X25 MM
B
First screw bolts B to the Left and Right Panels (7 & 10), then assemble
the Left and Right Panels (7 & 10) to the assembled part in step A3/B3
as explained in page 5.
Use screws G to assemble the Sliders (17)
to the Left and Right Panels (7 & 10).
Use screws E to assemble the Bottom Panel (15).
ATTENTION: To avoid misalignments, screw loose
and do not tighten them until all are in place!

RTA-2335 P.13
11
12
13
1
15
11
12
16
2X2
SCREWS
G
8PCS
3X12 MM
19
19
20
20
23
18
JX8
1
SCREWS
4PCS
6X40 MM
F
17
Use screws F to assemble the Bottom
Panel (15) to the Main Structures (1).
ATTENTION: To avoid misalignments,
screw loose and do not tighten them
until all are in place!
First tear off the protective film of the Adhesive
Foam Tapes (J), stick them to the Left and Right
Top Panels (11 & 12) as shown, then carefully lay
down the Glass Top (16).
Insert the Grommets (2) to the Bottom Panel (15).
Use screws G to assemble the drawers to the
Sliders (17).

RTA-2335 P.14
24 X2
SCREWS
4PCS
3X15 MM
A
25
14
Use screws A to assemble
to the Hinges (24).
the Long Top
Panel (25)
If the door does not close properly, you can adjust its position by unscrewing
loose the corresponding screws on the hinges:
When the optimal position has been reached, re-tighten the screws.
Adjusts the door
vertically
Adjusts the door
horizontally Adjusts the door side-to-side
when it is closed.

RTA-2335 P.15
26
27
15
16
A B
Insert the Short Top Panel (26) and the
Long Grommet (27).
Tighten any and all screws that are still loose, and
ENJOY YOUR NEW UNIT!

English
- DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT OR EXTREME
ENVIRONMENTAL CONDITIONS. ANY DAMAGE RESULTING FROM SUCH
EXPOSURE IS NOT COVERED BY THE PRODUCT’S WARRANTY.
- THE PREFERABLE METHOD TO CLEAN THE SURFACES IS TO WIPE THEM
USING A SOFT CLOTH DAMPENED WITH A SOLUTION SOAP AND WATER,
THEN DRY WITH A CLEAN TOWEL.
- DO NOT SPRAY SOLVENTS OR CLEANING AGENTS DIRECTLY OVER THE
SURFACES, STRUCTURAL TUBES OR METAL PARTS.
- DO NOT LEAN, SEAT OR STAND OVER THE UNIT.
- DO NOT ALLOW CHILDREN TO PLAY OVER/UNDER THE UNIT, NOR ALLOW
THEM TO REACH INSIDE ANY COMPARTMENTS WITHOUT THE SUPERVISION
OF AN ADULT.
- BEFORE MOVING OR TRANSPORTING THE UNIT, MAKE SURE THAT:
ALL HEAVY OBJECTS OR THAT MIGHT FELL OFF ARE REMOVED FROM
THE UNIT.
IF THE UNIT ARE ON CASTERS (WHEELS), MAKE SURE THAT ALL ARE
UNLOCKED.
THE UNIT MUST BE HANDLED BY AT LEAST 2 PERSONS.
WHEN LIFTING THE UNIT, USE BOTH OF YOUR HANDS, AND BEND YOUR
KNEES. REMEMBER TO ALWAYS LIFT WITH YOUR LEGS, NOT YOUR BACK.
- IN CASE OF DAMAGE TO ANY PARTS, NOTIFY THE VENDOR AS SOON AS
POSSIBLE.
- IN CASE OF GLASS BREAKAGE (IF THE UNIT HAS A GLASS TABLE TOP OR
PARTS MADE OF GLASS) DO NOT HANDLE THE BROKEN GLASS WITH YOUR
BEAR HANDS, AND CONTACT THE VENDOR IMMEDIATELY. DO NOT ALLOW
CHILDREN NEAR THE BROKEN GLASS.
CARE AND MAINTENANCE