RTA Techni Mobili RTA-8407 User manual

REV.FP-4-7530-0823
CONTEMPORARY DESK WITH 3 STORAGE DRAWERS
MODEL RTA-8407
ASSEMBLY INSTRUCTIONS
Thank you for purchasing our product

N
x1
M
x1
K
x3
L
x3
A
x1 B x1 C x1
D
x1 E x1 F x1 G x1
H
x3 I x3 J x3
P.1 P.1
RTA-8407
Tabletop Left back panel Left side panel
(Front)
(Back)
(Back)
(Front)
MAIN PARTS LIST
Replacement Parts for International
Customers & AK-HI-PR orders:
RTA Products will replace the part free of
charge, while the customer is responsible
for shipping costs plus any International
local taxes or duties.
Do a quick inventory
of all the parts and
hardware listed below.
For Support, assembly questions
& Replacement Parts within the
48 Contiguous United States:
Please email us at:
[email protected]
Right side panel Middle side panel Right shelf panel Right bottom panel
Drawer front panel Drawer left panel Drawer right panel Drawer back panel
Drawer bottom
board
15.5"
Right-Top back
board Right-bottom back
board
(Back)
(Front)
12.8"
14.8"
13.1"
14.8"
13.5"

Cover for
cam lock
RTA-8407
(Back)
(Back)
(Left)
(Left)
(Front)
P.2 P.2
MAIN PARTS LAYOUT (For reference)
HARDWARE LIST AND INCLUDED TOOLS
TOOLS REQUIRED BUT NOT INCLUDED
Hammer
Mallet
Phillips Screwdriver
PART QTY SIZE / DESCRIPTION ITEM
3
4
5
6
M8x20
Wooden Dowel
2
1
24
24
Sets M6x30 Cam
lock and bolt
M3.5x15
M3x16
M4x38
12
4
12
12
M5x8
Euro screw
15.75"
7
12
Drawer sliders,
Set of 4 pieces
8
3
Sets
3
Sets Metal handle
with screw
9
2Plastic corner
bracket
10
6Nail-in glide stud
11
If you decide to use your own power driver:
• Make sure to have the appropriate hex or
Phillips bits.
• Start using at a low torque or speed to
avoid stripping the screws.
(Front)
(Front)
(Right)
(Right)

P.3 P.3
RTA-8407
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
M6
30mm
M6x30
• Make sure you understand which
hardware will be used on each step. Using
the wrong size of screw, bolt or pin might
strip the threads or cause damage to the
part in which it is being used.
• To avoid misalignments, always leave the screws
loosely and do not tighten them until all the pieces
are positioned correctly.
• Do not overtighten or force the screws as they might
break, strip, damage the threads of the holes, or get
stuck inside the parts.
• If the hole seems to small for the screw, make sure
you are using the correct size of screw and/or that
you are installing it in the correct hole.
• Sometimes on the wood panels the laminate or
material might be covering the hole partially or
entirely, if there is no visible hole or if it looks too
small, pass and press the tip of your finger over the
area to feel its indentation, and carefully pierce the
laminate to uncover the hole underneath.
• Do not discard this manual or any of the packaging
material until the unit is completely assembled.
• Please read the assembly instructions throughly and
follow step by step.
• The product is not reversible, it assembles ONLY
as shown in the front page, with the drawers on
the RIGHT side. The drawers cannot install on
the LEFT side.
Thank you!
12
Leave loose,
tighten all together
√
√
• The assembly might require of 2 persons for certain
steps. Before you start the instalation, make sure there
is someone else nearby to help you.
Do not
overtighten
• Please be kind to our planet, when done with the
assembly, recycle any of the packaging materials
that is accepted by your city or recycling service.
X

RTA-8407
P.4 P.4
1. Screw the bolt into the indicated hole on the
panel indicated in the assembly step.
CAM BOLT AND CAM LOCK TUTORIAL
THE INSTRUCTIONS BELOW
ARE NOT ACTUAL ASSEMBLY STEPS
This unit uses cam bolts and locks (also known as mini fixes).
If you are not familiar with this kind of hardware, the below is a tutorial
that explains how to use them on the steps where they are required.
2. Join the other panel (with the big hole) to the
panel with the bolt. If it comes with the cam
locks already pre-installed, make sure to align
them to receive the bolt's head (refer to point
3). There might be a very small gap between
the panels which is normal.
3. Insert the cam lock on the panel with the big
hole making sure it goes aligned to receive the
bolt's head.
4. Use a Phillips screwdriver to turn the cam
lock clockwise. This will lock the panels
togheter and also will close any gaps.
Cam lock
alignment
If the cam locks come
pre-in stalled, make sure they
are aligned (see point 3).
THE ASSEMBLY STEPS START ON NEXT PAGE
THIS IS ONLY
A TUTORIAL
THIS IS ONLY
A TUTORIAL
THIS IS ONLY
A TUTORIAL
THIS IS ONLY
A TUTORIAL

WE RECOMMEND TO PLACE THE PIECES OVER BLANKETS TO PROTECT THEIR
FINISH DURING ASSEMBLY.
RTA-8407
P.5 P.5
ASSEMBLY STEPS
STEP 1
Hardware
1Dowel 24
Pcs
With a hammer or wooden/rubber mallet, install the dowels 1into the indicated
holes on panels B, C, D, E, F, G, Iand J.
Tools (Not included)
B, C, D,
E, F & G
Closer to end
(Top)
(Bottom)
I & J
Lower hole

RTA-8407
(Back)
(Back)
(Back)
(Front)
(Back)
(Front)
(Front)
P.6 P.6
(Bottom)
(Bottom)
(Bottom)
(Bottom)
(Back)
(Top)
(Top)
(Top)
(Top)
A
C
D
E
H
11
STEP 2
Hardware
2Bolts 24
Pcs
• Use a screwdriver to install the bolts 2into the indicated holes on panels A, C,
Dand H.
11 Glides 6
Pcs
Tools (Not included) A, C & D
Innermost
E
both sides
Innermost
• On panel E, install the bolts 2into the indicated holes on both sides of the panel.
Flip the panel,
the bolts attach
on both sides
Upper
• Use a hammer to install the glide studs 11 to the bottom of the panels C, Dand E.
H
H
E

RTA-8407
P.7 P.7
(Front)
(Front)
(Front)
(Front)
(Front)
(Front)
(Back)
(Back)
(Top)
(Top)
STEP 3
Hardware
7M5x8
(Euro)
(Right)
(Left)
12
Pcs
• Grab all 3 sets of sliders 8(total 12 pcs) and separate them according to their
shape:
• The "Flat" ones will be used on this step.
• The "L shaped" (their profile looks like an "L") won't be used until step X, so
set them aside.
8
"Flat" sliders
6
Pcs
Tools (Not included) The "Flat" pieces will
be used in this step.
8"L" Shaped
8"Flat"
RIGHT, x3
LEFT, x3
RIGHT, x3
LEFT, x3
D
E
(Front)(Front)
8"Flat", LEFT
8"Flat", RIGHT
The "L" shaped pieces
won't be used until
step X, so please
them aside.
• Use a screwdriver to install the "Flat" sliders 8to the right panel Dand the left panel Ein the
indicated holes, but please note the following:
• Pay attention to the orientation of the panels, identify what is the top, bottom, front and back.
• Pay attention to the orientation of the sliders, identify the front with the wheel.
• Screw first at the FRONT, on the 4th hole .
• There will be 2 empty holes above the wheel on the sliders.
Front hole
Back hole

RTA-8407
P.8 P.8
STEP 5
E
F
G
Cam locks
alignment on
Fand G
• With the help of nother person, turn the piece over its backs and assemble the
shelf Fand the bottom panel G with cam locks 2as explained in the Cam Lock
Tutorial Page.
STEP 4
Hardware
2Cam lock 4
Pcs
• With the pieces positioned upside-down and as shown, join the panels Cand
Eto panel Bwith cam locks 2as explained in the Cam Lock Tutorial Page.
Tools (Not included)
Turn over its back
2
Hardware
2Cam lock
(Back)
(Back)
(Front)
(Front)
(Top)
(Front)
(Back)
(Bottom)
4
Pcs
Tools (Not included)
(Top)
(Bottom)
(Bottom)
(This is the
unfinished side)
(Back)
(Back)
(Top)
(Bottom)
(Back)
Grooves
FIRST
THEN
This step
requires of
2 persons

RTA-8407
P.9 P.9
This step
requires of
2 persons
STEP 6 • First insert the right-lower board Nthrough the grooves of panels Fand G, and
into the groove of panel E.
• Then assemble the right panel Dto panels Fand Gwith cam locks 2as
explained in the Cam Lock Tutorial Page.
• Finally, and with the help of another person, bring the unit upright.
Hardware
2Cam lock 4
Pcs
Tools (Not included)
Cam locks
alignment on
Fand G
2nd: INSTALL D
1st: INSERT N
(Top)
3rd: TURN UPRIGHT
Turn upright
(Front)
(Front)
(Back)
(Top)
(Bottom)