RTA Techni Mobili RTA-4985 User manual

MODEL RTA - 4985
Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Please save this manual for future reference.
ASSEMBLY INSTRUCTIONS
Complete video assembly demonstration is available at:
www.rtaproducts.com/assembly-videos.htm

RTA-4985 P.3
PARTS LIST
341 2
1
2
5
6
4
11
12
13
16
18
23
22
32
27
19
X3
X8
7
X8
58
67
X8 X2
9
10
11 12 13
CPU Left Panel CPU Right Panel Studs CPU Bottom Panel
CPU Back Panel CPU Top Panel Base Tubes Hinges
Auxiliary Panel
File Cabinet Bottom
Panel
File Cabinet Left
Panel
File Cabinet Right
Panel
Metal Pin

P.4
14 16
15
18 19 20
21
22 23 24
25 26 27 28
29 30 31 32
33 34
Right
Left
17
X3 SET
35 36
Left
Right
X3
X4
X4
X2 X2 X2 X3
X2
X2 X4
RTA-4985
Drawer Sliders File Cabinet Back
Panel
File Cabinet Top
Panel
Central Panel
Main Panel Supporting Tubes for
Main Panel Keyboard Slider
Slider’s Base Keyboard Panel CPU Door Handles
Small Drawer Left
Panel
Small Drawer Right
Panel
Small Drawer Front
Panel
Drawer Bottom Panel
Small Drawer Back
Panel
Bottom Drawer Left
Panel
Bottom Drawer Right
Panel
Bottom Drawer Front
Panel
Bottom Drawer Back
Panel Hanging Files Tubes Metal Pin Grommet

P.5
A
B
D
C
E
4X20 MM
3
12
24
8
16
PART QTY. ITEM PART QTY. ITEM
6X40 MM
F48
G8 4X16 MM
4X4 MM
4X14 MM
H
I
6X12 MM
4
4
1
6X35 MM
3
J
K32 6X25 MM
4X35 MM
3X15 MM
Φ40 MM
SCREWS
RTA-4985

30mm
P.6
RTA-4985

P.7
25
26
27
25
26
28
29
SCREWS
4PCS
4X35 MM
B
27
24
SCREWS
4X20 MM
D
2PCS
Left
Right
14
14
SCREWS
C
4PCS
3X15 MM
1
23
45
25
ASSEMBLY STEPS:
25
26
SCREWS
4PCS
6X25 MM
K
RTA-4985
First screw bolts K to the Front Panel (27),
then assemble the Small Drawer Left & Right
Panels (25 & 26) as explained in page 5.
Slide in the Drawer Bottom Panel (28).
Use screws B to assemble
the Small Drawer Back
Panel (29) to the Small
Drawer Left & Right Panels
(25 & 26).
Grab 2 sets of the Drawer Sliders (14) and separate the flat
ones from the “L” shaped ones. Place the drawer upside-
down as shown and use screws C to assemble the “L” shaped
Sliders to the Small Drawer Left & Right Panels (25 &26) as
shown.
IMPORTANT: REFER TO THE DRAWINGS FOR THE CORRECT
POSITION OF THE SLIDERS. If they get installed incorrectly,
the drawers will raise 1" with a gap at the bottom and the top
drawer will not close!
Use screws D to fix the Handles (24)
to the Small Drawer Front Panel (27).
REPEAT STEPS 1 THRU 5 FOR
THE SECOND SMALL DRAWER

P.8
SCREWS
4PCS
4X35 MM
B
67
8
9
SCREWS
4PCS
6X25 MM
K
30
31
32
30
31
28
30
31
33
34
33
32
RTA-4985
First screw bolts K to the Bottom Drawer Front
Panel (32), then assemble the Bottom Drawer
Left & Right Panels (30 & 31) as explained in
page 5.
Slide in the Drawer Bottom Panel (28).
Use screws B to assemble the Bottom Drawer Back
Panel (33) to the Bottom Drawer Left & Right Panels
(30 & 31).
Insert the Hanging Files Tubes (34) thru the Bottom Drawer Back Panel (33)
AND SLOWLY AND CAREFULLY screw into the Bottom Drawer Front Panel (32).
IMPORTANT: OVERTIGHTENING THE TUBES WILL DAMAGE THE FRONT
PANEL BY MAKING A BUMP OR EVEN PERFORATING THE PANEL ON THE
OTHER SIDE, AND SUCH DAMAGE IS NOT COVERED BY THE PRODUCT’S
WARRANTY!
OVERTIGHTENING WILL
DAMAGE THE FRONT PANEL!

P.9
10
11
13
12
RTA-4985
Right
Left
14
14
SCREWS
C
4PCS
3X15 MM
30
Grab the other set of the Drawer Sliders (14) and separate the flat
ones from the “L” shaped ones. Place the drawer upside- down as
shown and use screws C to assemble the “L” shaped Sliders to the
Bottom Drawer Left & Right Panels (30 &31) as shown.
IMPORTANT: REFER TO THE DRAWINGS FOR THE CORRECT
POSITION OF THE SLIDERS. If they get installed incorrectly,
the drawers will raise 1" with a gap at the bottom and the top
drawer will not close!
32
24
SCREWS
4X20 MM
D
2PCS
Use screws D to fix the Handle (24) to the
Bottom Drawer Front Panel (32).
X4
4
7
SCREWS
16PCS
4X14 MM
F
Use screws F to assemble the Base Tubes (7)
to the CPU Bottom Panel (4).
4
X4
3
Insert the Studs (3) into
the Base Tubes (7) and
tighten them well at the
same level.
14
SCREWS
4PCS
6X25 MM
K
First screw bolts K to the CPU Back Panel (5), then
assemble the CPU Left & Right Panels (1 & 2) as explained
in page 5. Please note: The CURVED side of the panels
are the FRONT of the cabinet, and the panels are WIDER
at the bottom than at the top.
Screw the Metal Pin (9) to the CPU Right Panel (2).

P.10
12
5
4
2
1
6
15
16
4
EX4
K
SCREWS
4PCS
6X40 MM
E
SCREWS
4PCS
6X40 MM
E
2PCS
6X25 MM
K
17
RTA-4985
Screw bolts K to the 2 back holes of the CPU Bottom Panel (4),
and screw bolts E to the 1st and 4th holes on the side (the 2nd
and 3rd holes are for receiving the wooden pins of panels 1 & 2).
(For the 2 back holes)
(For the 1st and 4th
holes on the sides)
Assemble the parts (1,2 & 5) that you assembled in step 14 to
the CPU Bottom Panel (4) as explained in page 5.
First screw bolts E to the CPU Top Panel (6), then assemble this
panel to Left & Right Panels (1 & 2) as explained in page 5.

P.11
10
35 X4
11
7
X4
11
X4
3
SCREWS
16PCS
4X14 MM
F
SCREWS
C
8PCS
3X15 MM
18 19
20
21
12 13
Left Right
14
14
14
X2 X2
RTA-4985
Insert the Metal Pins (35) into the holes of
the CPU Left & Right Panels (1 & 2) at your
desired height, then place the Auxiliary
Panel (10) over the pins. Use screws F to assemble the Base Tubes (7)
to the File Cabinet Bottom Panel (11).
Insert the Studs (3) into the Base Tubes (7) and tighten them well
at the same level.
Get 2 sets of the Flat Sliders (14) and use screws C to assemble
them to the top and middle of the File Cabinet Left & Right Panels
(12 & 13) as shown. Please note: The CURVED side of the panels
are the FRONT of the cabinet, and the panels are WIDER at the
bottom than at the top. The wheel on the sliders go facing to the
FRONT and the screw goes on the hole after the wheel as shown.

P.12
12
13
16
22
23 24
K
EX4
11
SCREWS
4PCS
6X25 MM
K
SCREWS
4PCS
6X40 MM
E
SCREWS
4PCS
6X40 MM
E
2PCS
6X25 MM
K
15
12
13
12
13
15
11
RTA-4985
First screw bolts K to the File Cabinet Back Panel (15), then assemble
this panel to the File Cabinet Left & Right Panels (12 & 13) as explained
in page 5.
Screw bolts K to the 2 back holes of the File Cabinet Bottom
Panel (11), and screw bolts E to the 1st and 4th holes on the
side (the 2nd and 3rd holes are for receiving the wooden pins
of panels 12 & 13). Then assemble the parts (12, 13 &15) to
the File Cabinet Bottom Panel (11), as explained in page 5.
(For the 2 back holes)
(For the 1st and 4th
holes on the sides)
First screw bolts E to the File Cabinet Top
Panel (16), then assemble this panel to
Left & Right Panels (12 & 13) as explained
in page 5.

P.13
5
15
17
X3
18
19
SCREWS
12PCS
4X14 MM
F
25
26
27
SCREWS
4PCS
6X25 MM
K
17
36
13
12
Left Right
14
14
SCREWS
C
4PCS
3X15 MM
14
12
RTA-4985
Get the other set of the Flat Sliders (14) and use
screws C to assemble them to the bottom of the
File Cabinet Left & Right Panels (12 & 13) as
shown. Please note: The wheel on the sliders
go facing to the FRONT and the screw goes on
the hole after the wheel as shown.
First screw bolts K to the CPU Back Panel (5) and the File
Cabinet Back Panel (15), then assemble the Central
Panel (17) as shown and as explained in page 5. Finally,
place the Grommet (16) into the hole of the Central
Panel (17).
Use screws F to assemble the Supporting Tubes for Main Panel (19)
to the Main Panel (18).

P.14
21
X4
Left
20
Right
20
SCREWS
4PCS
4X4 MM
I
19 X3
5
15
18
SCREWS
3PCS
6X35 MM
A
4PCS
6X25 MM
K
3PCS
JΦ40 MM
28
30
29
18
21
X4
H
SCREWS
4PCS
6X12 MM
RTA-4985
Use screws H to assemble the Sliders Bases (21) to the Main Panel (18).
Use screws I to assemble the Keyboard Sliders (20)
to the Sliders Bases (21) as shown.
TO MAKE SURE THE SLIDERS ARE
ASSEMBLED CORRECTLY:
- The flat side of the sliders are positioned touching the bases.
- The moving part of the sliders will slide to the front.
- The tabs on the sliders will face up.
- Screw the sliders at the back first, then close it and screw at
front.
- The screw is inserted from the outside thru the bases and into
the holes of the sliders.
First screw bolts K to the back holes of the Main Panel (18). Then place the washers J over the
front holes of the CPU and Drawers cabinets as shown. Finally, and with the help of another person,
carefully place the tabletop over the frame of the desk and secure at the front with screws A, and
at the back by locking the cam locks as explained in page 5.

P.15
22
Right
20
Left
20
SCREWS
4PCS
4X14 MM
F
23
8
23
24
SCREWS
G
4PCS
4X16 MM
SCREWS
4X20 MM
D
2PCS
31
32 33
8
RTA-4985
Open the sliders and place the Keyboard Panel (22) over the tabs, making the holes on the
tabs and the panel coincide. Use screws F to secure the panel to the sliders from underneath
as shown.
Use screws C to assemble the Hinges (8)
to the CPU Door (23).
Use screws D to assemble the Handle (24) to the
CPU Door (23).

P.16
8
X2
1
SCREWS
G
4PCS
4X16 MM
34
RTA-4985
Use screws G to assemble the
Hinges (8) to the CPU Left Panel (1).
If the door does not close properly, you can adjust its position by unscrewing
loose the corresponding screws on the hinges:
Adjusts the door vertically
Adjusts the door
horizontally
Adjusts the door side-to-side
when it is closed.
When the optimal position has been reached, re-tighten the screws.

P.17
27
27
32
35
36
RTA-4985
Insert the drawers into the cabinet, starting with the bottom drawer.
For the top drawer, you might have to insert it at a downward tilted angle.
Tighten any and all screws that are still loose, and
ENJOY YOUR NEW UNIT!

English
- DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT OR EXTREME
ENVIRONMENTAL CONDITIONS. ANY DAMAGE RESULTING FROM SUCH
EXPOSURE IS NOT COVERED BY THE PRODUCT’S WARRANTY.
- THE PREFERABLE METHOD TO CLEAN THE SURFACES IS TO WIPE THEM
USING A SOFT CLOTH DAMPENED WITH A SOLUTION SOAP AND WATER,
THEN DRY WITH A CLEAN TOWEL.
- DO NOT SPRAY SOLVENTS OR CLEANING AGENTS DIRECTLY OVER THE
SURFACES, STRUCTURAL TUBES OR METAL PARTS.
- DO NOT LEAN, SEAT OR STAND OVER THE UNIT.
- DO NOT ALLOW CHILDREN TO PLAY OVER/UNDER THE UNIT, NOR ALLOW
THEM TO REACH INSIDE ANY COMPARTMENTS WITHOUT THE SUPERVISION
OF AN ADULT.
- BEFORE MOVING OR TRANSPORTING THE UNIT, MAKE SURE THAT:
ALL HEAVY OBJECTS OR THAT MIGHT FELL OFF ARE REMOVED FROM
THE UNIT.
IF THE UNIT ARE ON CASTERS (WHEELS), MAKE SURE THAT ALL ARE
UNLOCKED.
THE UNIT MUST BE HANDLED BY AT LEAST 2 PERSONS.
WHEN LIFTING THE UNIT, USE BOTH OF YOUR HANDS, AND BEND YOUR
KNEES. REMEMBER TO ALWAYS LIFT WITH YOUR LEGS, NOT YOUR BACK.
- IN CASE OF DAMAGE TO ANY PARTS, NOTIFY THE VENDOR AS SOON AS
POSSIBLE.
- IN CASE OF GLASS BREAKAGE (IF THE UNIT HAS A GLASS TABLE TOP OR
PARTS MADE OF GLASS) DO NOT HANDLE THE BROKEN GLASS WITH YOUR
BEAR HANDS, AND CONTACT THE VENDOR IMMEDIATELY. DO NOT ALLOW
CHILDREN NEAR THE BROKEN GLASS.
CARE AND MAINTENANCE