RTA Techni Mobili RTA-0039LC User manual

RTA-0039LC
Thank you for purchasing one of our products.
Please no not discard this manual, the cartons or the packaging material until the unit has been
completely assembled.
Please read carefully the assembly instructions before the installation.
ASSEMBLY INSTRUCTIONS

GENERAL DIMENSIONS:
SHORT SIDE: 55”
LONG SIDE: 60.75”
HEIGHT: 30”
NET WEIGHT: 100 Lbs.
SHIPS IN 2 BOXES.
MAXIMUM WEIGHT CAPACITIES
(DO NOT EXCEED THESE LIMITS)
30”
66 Lbs.
110 Lbs.
PRODUCT DIMENSIONS
P.2
RTA-0039LC
P.2
Floor to bottom
of keyboard
tray: 25.75”
19.5”
8mm thick
tempered
glass
110 Lbs.
33 Lbs.

MAIN PARTS LIST
P.3
RTA-0039LC
P.3
Left
Structure
Right
Structure
Short Glass.
35.5” x 19.5”
(90cmx50cm)
Corner Glass
r = 19.5”
(50cm)
Keyboard
Panel
Corner
Structure
Left
Structure
Right
Structure
Long Central Tube
36” x Ø 2”
(91.4cm x Ø5cm)
Short Top Tube
30” x Ø 1.25”
(76cm x Ø3.2cm)
Slider Base Left Slider Right Slider
Connector for Top Tubes
Ø 38 mm; Ø 32 mm
Connector for
Central Tubes
Ø 52 mm
Cover for Top
Tubes
Ø 40 mm
Cover for Central
Tubes
Ø 50 mm
Long Glass
41.25” x 19.5”
105cm x 50 cm)
Short Central Tube
30” x Ø 2”
(76.4cm x Ø5cm)
Long Top Tube
35.75” x Ø 1.25”
(91cm x Ø3.2cm)

P.4
SKU 86333
P.4
MAIN PARTS LIST
Screw
8x80mm
Screw
6x65mm
Screw
6x25mm
Screw
12mm
Screw
6x9mm
Stud
#6, Ø 30mm.
Allen Key
5mm
O’ ring
Ø 8mm
Cap nut
#6
Wrench
10mm
Screw
4x5mm
Washer
Ø 8mm
Allen Key
4mm You will also need a
screwdriver that is not
included with the
product.

⚠BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS
AND WARNINGS.
P.5
RTA-0039LC
P.5
☛Do a quick inventory to make sure the product contains all the parts and hardware.
☛Missing, damaged and defective parts can be replaced at no cost to you. Please
refer to the CONTACT and the WARRANTY cards included with the product.
☛If during assembly you find an issue or need clarification, please contact our Customer
Service for assistance. Please refer to the CONTACT card included with the product.
☛On each step read the instructions and analyze the illustrations thoroughly before
proceeding to do the assembly.
☛To avoid misalignments, always leave the screws loose and tighten them until all pieces
are positioned correctly.
☛Do not overtighten or force the screws as they might break, strip, damage the threads
of the holes or get stuck inside the part.
☛Sometimes the laminate might cover partially or entirely the hole on the wooden panel,
but the hole should still be located under the laminate.
☛If there is no visible hole for the screw, pass and press the tip of your finger over the
area where the hole should be located to feel the indentation.
☛Make sure you understand which hardware will be used on each step. Using the wrong
size of screw might strip the threads on the screw or the hole, or leave the parts
damaged or unsecured.
☛Do not discard this manual or any of the packaging material until the unit has been
completely assembled.

ASSEMBLY STEPS
P.6
RTA-0039LC
P.6
Insert the studs (1) into the bottom of all the structures (A), (B), (C) and (D) as shown.
Pay attention to
the orientation
Of the structure.
Using screws (U) and O’ rings (2), assemble the structure (A) to the central tube (J) and top tubes (L), with
connectors (Q) and (R) in between as shown.
U: x3
8x80mm
2: x3
Ø8mm
1: x8
#6, Ø30mm
Q: x2
R: x1

P.7
RTA-0039LC
P.7
Insert the covers (S) to the top tubes, and the covers (T) to the central tube as shown.
Using screws (U) and O’ rings (2), assemble the structure (B) to the tubes (J) and (L), with the connectors (Q) and
(R) in between as shown.
U: x3
8x80mm
2: x3
Ø8mm
R: x1
Q: x2
S: x4
T: x2

P.8
RTA-0039LC
P.8
Insert the covers (S) into the top tubes, and the covers (T) to the central tube as shown.
U: x6
8x80mm
2: x6
8mm
Using screws (U) and O’ rings (2), assemble the top tubes (M) and central tube (K) in between the structures (C)
and (D), with the connectors (Q) y (R) in between as shown, and in the same way as in steps 2 and 3.
R: x2
Q: x4
S: x4
T: x2

P.9
RTA-0039LC
P.9
THIS DESK CAN BE ASSEMBLED 3 WAYS:
1) WITH THE SHORT SECTION
(KEYBOARD) TO THE LEFT.
2) WITH THE SHORT SECTION
(KEYBOARD) TO THE RIGHT.
3) AS 2 SEPARATE TABLES
(WITHOUT THE CORNER SECTION).
STEP #7 EXPLAINS HOW TO DO THE CONFIGURATIONS.

P.10
RTA-0039LC
P.10
Once you have decided which configuration you will use for your desk, place the structures close to each other as
shown:
To have the short section (keyboard) on the LEFT: To have the short section (keyboard) on the RIGHT:
To leave as 2 separate tables, just skip the steps 8 and 9, and continue with step 10.
Assemble loosely the corner structure (I) in between the main structures of the sections using screws (V) and
cap nuts (4) as shown. Do not tighten any screws yet!
Insert the screws from the
main structures toward the
corner structure.
SCREW LOOSELY!
V: x4
6x65mm
4: x4
#6