RTI KX7s User manual

Reference Guide
It’s Under Control®
KX7s
In-Wall Controller
If you are encountering any problems or have a question about your RTI product, please contact RTI Technical
Support for assistance (see the Contacting RTI section of this guide for contact details).
RTI provides technical support by telephone or e-mail. For the highest quality service, please have the following
information ready, or provide it in your e-mail.
• Your Name
• Company Name
• Telephone Number
• E-mail Address
• Product model and serial number (if applicable)
If you are having a problem with hardware, please note the equipment in your system, a description of the
problem, and any troubleshooting you have already tried.
Please do not return products to RTI without a return authorization.
Service & Support
For news about the latest updates, new product information, and
new accessories, please visit our web site at:
www.rticorp.com
For general information, you can contact RTI at:
Remote Technologies Incorporated
5775 12th Ave. E Suite 180
Shakopee, MN 55379
Tel. [phone]
Fax [phone]
[email protected]
Contacting RTI
Safety Suggestions
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. Any changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the device.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including interference that may cause undesired operation.
Read and Follow Instructions. Read all safety and operating instructions before operating the unit.
Retain Instructions. Keep the safety and operating instructions for future reference.
Heed Warnings. Adhere to all warnings on the unit and in the operating instructions.
Heat. Keep the unit away from heat sources such as radiators, heat registers, stoves, etc., including ampliers that produce heat.
Power Sources. Connect the unit only to a power supply of the type described in the operating instructions, or as marked on the unit.
Power Cord Protection. Route power supply cords so that they are not likely to be walked on or pinched by items placed on or against them, paying particular attention to the cord plugs at
power receptacles and at the point at which they exit from the unit.
Water and Moisture. Do not use the unit near water—for example, near a sink, in a wet basement, near a swimming pool, near an open window, etc.
Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled into the enclosure through openings.
Servicing. Do not attempt any service beyond that described in the operating instructions. Refer all other service needs to qualied service personnel.
Damage Requiring Service. The unit should be serviced by qualied service personnel when:
The power supply cord or the plug has been damaged.
Objects have fallen or liquid has been spilled into the unit.
The unit has been exposed to rain.
The unit does not appear to operate normally or exhibits a marked change in performance.
The unit has been dropped or the enclosure has been damaged.
Limited Warranty
RTI warrants its products for a period of three (3) years (one year for included battery packs); or for a period of time compliant with local laws when applicable from the date of purchase
from RTI or an authorized RTI distributor.
This warranty may be enforced by the original purchaser and subsequent owners during the warranty period, so long as the original dated sales receipt or other proof of warranty coverage is
presented when warranty service is required.
Except as specied below, this warranty covers all defects in material and workmanship in this product. The following are not covered by the warranty:
Damage resulting from:
1. Accident, misuse, abuse, or neglect.
2. Failure to follow instructions contained in this Guide.
3. Repair or attempted repair by anyone other than Remote Technologies Incorporated.
4. Failure to perform recommended periodic maintenance.
5. Causes other than product defects, including lack of skill, competence or experience of user.
6. Shipment of this product (claims must be made to the carrier).
7. Being altered or which the serial number has been defaced, modied or removed.
DECLARATION OF CONFORMITY (DOC)
The Declaration of Conformity for this product can be found on the RTI website at: www.rticorp.com/declaration
Copyright © 2020 • Remote Technologies Incorporated • All rights reserved. 70-210220-14 V1.0
The KX7s is designed for sophisticated installations that require a touchpanel with the size and power to take
command of a room’s environmental and media technology. With advanced features like a multi-touch capacitive
touchscreen and direct IR/RS-232 control, the KX7s possesses the style and user-friendliness required to t any
type of setting.
The KX7s provides superior quality and reliability as well as these features:
• Stylish low-prole faceplate with a gloss nish (standard is white, however other faceplate options are available).
• 800x480 WVGA LCD with integrated multi-touch capacitive touch screen.
• RS-232 port for direct control of devices via RS-232 communication.
• High output IR port for direct control.
• Network connectivity via an integrated 10/100 Base-T Ethernet port.
• Completely customizable and programmable.
• Powered using RTI Control Port or PoE (Power over Ethernet).
• Built-in ambient light and proximity sensors.
• Field upgradable rmware.
• USB and Ethernet programming.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including interference that may cause undesired operation.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes:
1. Ce dispositif ne peut causer des interférences nuisibles.
2. Cet appareil doit accepter toute interférence reçue y compris des interférences qui peuvent provoquer un fonctionnement indésirable.
Industry Canada Compliance Statement

It’s Under Control®
Connection Options
Ethernet
(Cat-5/6 cable)
RJ-45>DB-9
Adapter
KX7s (Rear)
RS-232 (1)
POWER / IR
SENSE
IR / SERIAL / SENSE
EXPANSION +12VDC, 1A
MULTI-PURPOSE I/O PORTS RS-232 (2)
ETHERNET
RS-232 (3)
TRIGGERS RELAYS
RTI COM
POWER
123123 1 2 3
GND INPUT
HIGH OUT
ABABAB
4
1 2 3 56
+12VDC
3-24VDC 12V,100mA MAX 3A@30VDC MAX
GND
GND
RS-232 Controlled Device
(Ex. Video Projector)
The following diagram shows a “control system operation” of the KX7s, which utilizes an RTI control processor (RTI XP-6s shown) and an
RTI connecting block (RTI CB-8 shown).
CB-8 Connecting Block
XP-6s Control Processor
Mounting Wings (2)
- One located on bottom of KX7s also.
Ethernet Network
Router or Switch
MOUNTING
The KX7s is designed for ush-mount, in-wall installations. It requires an available mounting depth of 2 inches (52.5mm) from the surface of the wall.
IMPORTANT NOTE: There is little margin for error when tting the KX7s into the wall opening.
Make sure to use the included cardboard cut-out template to create the correct size opening in the wall. Additionally, carefully double-check that all
measurements taken using the cardboard cut-out template are accurate.
MOUNTING HEIGHT
The recommended mounting height for the KX7s is between 54 inches (1.37m) and 60 inches (1.52m) from the bottom of the faceplate.
MOUNTING WINGS
Two mounting wings are located on the top and bottom of the KX7s, which can be used to secure the KX7s to drywall in retrot installations. Place KX7s in
the opening in the wall and tighten the mounting wing screws located on the front of the KX7s (bezel removed).
CONDUIT BOX
For new construction installations a conduit box may be purchased separately from an RTI distributor. For mounting instructions, refer to the conduit box
installation guide
CONNECTIONS
CONTROL PORT
The Control Port on the KX7s uses a Cat-5/6 cable with RJ-45 termination. When used in conjunction with an RTI control processor (e.g. RTI XP-6s) and
an RTI connecting block (e.g. RTI CB-8), this port serves as the power source for the KX7s in addition to infrared and RS-485 communication.
ETHERNET PORT
The KX7s is designed for connection to a LAN via Cat-5/6 cabling with RJ-45 termination. Additionally, the KX7s can be optionally powered using Power-
Over-Ethernet, allowing the power to be extended to the KX7s over the same Cat-5/6 cable that carries Ethernet communication. When powering the
KX7s using PoE, a class 3 PoE router or PoE injector must be used.
RS-232
The KX7s is capable of direct RS-232 communication using a Cat-5/6 cable with RJ-45 termination. A DB9 - RJ45 adaptor is included with the KX7s.
NOTE: RS-232 communication should be limited to 50 feet (16m) depending on baud rate.
Installation & Operation
DB-9
Pin Signal Signal
Name Description
1 DCD Carrier Detect
2 RXD Receive Data
3 TXD Transmit Data
4 DTR Data Terminal Ready
5 GND Signal Ground/Common
6 DSR Data Set Ready
7 RTS Request To Send
8 CTS Clear To Send
9 NC Not Connected
RJ-45 (KX7s RS-232 Output)
Pin Signal Signal
Name Description
1 DSR Data Set Ready
2 DCD Carrier Detect
3 DTR Data Terminal Ready
4 GND Signal Ground/Common
5 RXD Receive Data
6 TXD Transmit Data
7 CTS Clear To Send
8 RTS Request To Send
DB9 - RJ45 ADAPTOR PINOUT
FERRITE RING INSTALLATION
In order to comply with regulatory agency standards for EMI
emissions, the included ferrite ring must be installed on any cable
attached to the KX7s Ethernet Port, Control Port, RS232 Port or
Video Input.
• To open the ferrite ring enclosure pry open the plastic latch.
• Insert cables into the ferrite ring at the end of the cables as
close to the KX7s enclosure as possible.
• Close ferrite ring enclosure until the latch snaps in place.
Ferrite ring open Ferrite ring closed - with cables
KX7s Front (Bezel removed)
PROGRAMMING
THE TOUCHSCREEN DISPLAY
The KX7s touchscreen display is programmed using the RTI Integration Designer Programming Software. Normally it is organized into a series of pages
containing objects (buttons, text, graphics, etc.) that are related to each other. For example, they may all display information necessary for controlling a
particular music server.
UPDATING FIRMWARE
It is highly recommended that this and all RTI products have the latest rmware installed. The rmware can be found in the Dealer section of the RTI
website (www.rticorp.com). Install the rmware using a USB cable (USB A to Mini B).
UPDATING SOFTWARE
RTI’s Integration Designer data les can be downloaded to the KX7s using a USB cable (USB A to Mini B), or via hard-wired or wireless Ethernet. If the KX7s
is hard-wired to a LAN and the router has DHCP enabled, the initial data le can be made over Ethernet.
Mounting Wing Screws
Reset Button
USB Port
Ambient and Proximity Sensors
Pin 8
Pin 7
Pin 6
Pin 5
Pin 4
Pin 3
Pin 2
Pin 1
Ground
Ground
Infrared
+12 to +16 VDC
+12 to +16 VDC
Infrared
RS-485-
RS-485+
Control Port
(Cat-5/6 cable)
RS-232 Port
(Cat-5/6 cable)
Control Port
(Pinout)