RUCKUSQ ZoneFlex 7761-CM User manual

Ruckus Wireless™ZoneFlex™
Outdoor Access Point
Release 9.3 User Guide
For the following outdoor ZoneFlex AP models:
■ZoneFlex 2741 802.11g Outdoor Access Point
■ZoneFlex 7762 Dual Band 802.11n Outdoor Access Point
■ZoneFlex 7762-S Dual Band 802.11n Outdoor Access Point with Sector
Antenna
■ZoneFlex 7762-T Dual Band 802.11n Outdoor Access Point with Omni
Antenna
■ZoneFlex 7762-AC Dual Band 802.11n Outdoor Access Point
■ZoneFlex 7762-S-AC Dual Band 802.11n Outdoor Access Point with
Sector Antenna
■ZoneFlex 7761-CM Dual Band 802.11n Outdoor Access Point with
Integrated Cable Modem
Part Number 800-70369-001
Published January 2012
www.ruckuswireless.com

i
About This Guide
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
1 Introducing the ZoneFlex Access Point
Overview of the ZoneFlex Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Unpacking the ZoneFlex Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting to Know the Access Point Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
ZoneFlex 2741 Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ZoneFlex 7762 Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ZoneFlex 7762-S Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ZoneFlex 7762-T Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ZoneFlex 7762-AC Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ZoneFlex 7762-S-AC Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ZoneFlex 7761-CM Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Supported Power Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cable Modem Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2 Installing the Access Point
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Prepare the Required Hardware and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Perform a Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Step 1: Preconfigure the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Configuring for Management by ZoneDirector . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Configuring for Standalone Operation or for Management by FlexMaster . . . . 33
Step 2: Verify Access Point Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Connect the Access Point to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Associate a Wireless Client with the Access Point . . . . . . . . . . . . . . . . . . . . . . . . 41
Contents

ii
Check the TR069 Status (FlexMaster Management Only) . . . . . . . . . . . . . . . . . . 41
Disconnect the Access Point from the Network . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Step 3: Deploy the Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Troubleshooting Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
3 Navigating the Web Interface
Logging Into the ZoneFlex Web Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Navigating the Web Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
If You Are Using a Dual Band ZoneFlex Access Point. . . . . . . . . . . . . . . . . . . . . . . . .45
4 Configuring the Access Point
Configuring Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Configuring Internet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
VLAN Settings Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Configuring NTP Server and Management VLAN . . . . . . . . . . . . . . . . . . . . . . . . 50
Default IP Addressing Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Obtaining and Assigning an IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Configuring L2TP Connection Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Configuring Local Subnets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Configuring Wireless Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Configuring Common Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Configuring Wireless # Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Configuring Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Setting Ethernet Port Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Working with 802.1X on Wired Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Working with Port-Based VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Configuring Hotspot Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Customizing Hotspot Optional Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Creating a Hotspot Walled Garden . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Allowing Unrestricted Access by MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5 Managing the Access Point
Viewing Current Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Viewing Current Internet Connection Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Viewing Current Local Subnet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

iii
Viewing Current Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Viewing Associated Wireless Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Changing the Administrative Login Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Enabling Other Management Access Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Viewing FlexMaster Management Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Pointing the AP to FlexMaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Working with Event Logs and Syslog Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Enabling Logging and Sending Event Logs to a Syslog Server . . . . . . . . . . . . . 102
Sending a Copy of the Log File to Ruckus Wireless Support . . . . . . . . . . . . . . . 103
Saving a Copy of the Current Log to Your Computer . . . . . . . . . . . . . . . . . . . . 103
Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Upgrading Manually via FTP or TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Upgrading Manually via the Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Upgrading Manually via Local File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Scheduling Automatic Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Rebooting the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Resetting the Access Point to Factory Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Running Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Where to Find More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Index

iv

i
About This Guide
About This Guide
This guide describes how to install, configure, and manage the Ruckus Wireless™
ZoneFlex™Access Point. This guide is written for those responsible for installing and
managing network equipment. Consequently, it assumes that the reader has basic
working knowledge of local area networking, wireless networking, and wireless
devices.
NOTE: If release notes are shipped with your product and the information there
differs from the information in this guide, follow the instructions in the release notes.
NOTE: Each ZoneFlex Outdoor AP model has its own Installation Guide or Getting
Started Guide that details specific hardware installation procedures for the particular
AP model. This User Guide does not cover installation procedures for these outdoor
APs. Refer to the Installation Guide or Getting Started Guide that shipped with your
product for model-specific installation instructions.
Most user guides and release notes are available in Adobe Acrobat Reader Portable
Document Format (PDF) or HTML on the Ruckus Wireless Support Web site at:
http://support.ruckuswireless.com/
Document Conventions
Tabl e 1 and Ta b l e 2 list the text and notice conventions that are used throughout this
guide.
Tabl e 1 . Text C onve n t ions
Convention Description Example
monospace Represents information as it
appears on screen
[Device name]>
monospace bold Represents information that
you enter
[Device name]> set
ipaddr 10.0.0.12
default font bold Keyboard keys, software
buttons, and field names
On the Start menu, click All
Programs.
italics
Screen or page names Click Advanced Settings.
The Advanced Settings page
appears.

ii
About This Guide
Related Documentation
In addition to this User Guide, each ZoneFlex Access Point documentation set
includes the following:
■Installation Guide/Getting Started Guide: Provides essential installation and
configuration information to help you get the AP up and running within minutes.
■Online Help: Provides instructions for performing tasks using the Access Point’s
Web interface. The online help is accessible from within the Web interface.
■Release Notes: Provide information about the current software release, including
new features, enhancements, and known issues.
NOTE: If you will be managing your ZoneFlex Access Points using ZoneDirector, refer
to the ZoneDirector User Guide (available from the Ruckus Wireless website).
Documentation Feedback
Ruckus Wireless is interested in improving its documentation and welcomes your
comments and suggestions. You can email your comments to Ruckus Wireless at:
[email protected]
When contacting us, please include the following information:
■Document title
■Document part number (on the cover page)
■Page number (if appropriate)
For example:
■Ruckus Wireless ZoneFlex Outdoor Access Point Release 9.3 User Guide
■Part number: 800-70369-001
■Page 88
Table 2. Notice Conventions
Icon Notice Type Description
Information Information that describes
important features or
instructions
Caution Information that alerts you to
potential loss of data or
potential damage to an
application, system, or device
Warning Information that alerts you to
potential personal injury

1
1
Introducing the ZoneFlex Access
Point
Overview of the ZoneFlex Access Point
Congratulations on your purchase of the Ruckus Wireless ZoneFlex Access Point!
ZoneFlex Access Points are the industry’s most easy to use, yet robust and feature-
rich Wi-Fi Access Points designed to bring power and simplicity together for large-
scale outdoor deployments.
Your ZoneFlex Access Point uses BeamFlex™, a patented antenna technology from
Ruckus Wireless that allows wireless signals to navigate around interference, extend
wireless signal range, and increase speeds and capacity for wireless networks. The
BeamFlex™ antenna system consists of an array of up to fourteen high-gain direc-
tional antenna elements that allow ZoneFlex Access Points to find quality signal paths
in a changing environment, and sustain the baseline performance required for
supporting data, audio and video applications.
Your ZoneFlex Access Point can be deployed in standalone mode or as part of the
ZoneFlex Smart WLAN system, in which it can be managed by either FlexMaster or
ZoneDirector WLAN controller.
NOTE: For more information on the ZoneFlex system (including FlexMaster and
ZoneDirector), BeamFlex, and other Ruckus Wireless technologies, visit
www.ruckuswireless.com.
In This Chapter
Overview of the ZoneFlex Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Unpacking the ZoneFlex Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Getting to Know the Access Point Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2
Introducing the ZoneFlex Access Point
Unpacking the ZoneFlex Access Point
Unpacking the ZoneFlex Access Point
1. Open the Access Point package, and then carefully remove the contents.
2. Return all packing materials to the shipping box, and put the box away in a dry
location.
3. Verify that all items listed in Package Contents below are included in the package.
Check each item for damage. If any item is damaged or missing, notify your
authorized Ruckus Wireless sales representative.
Package Contents
A complete Access Point package contains all of the items listed below:
■ZoneFlex Access Point
■Software License Agreement/Product Warranty Statement
■Installation Guide or Getting Started Guide
■(Mounting hardware, power cables and Ethernet cables differ by model and SKU;
for details, refer to the Installation Guide or Getting Started Guide included with
your ZoneFlex Outdoor Access Point package)
Getting to Know the Access Point Features
This section identifies the physical features of each ZoneFlex Access Point model that
is discussed in this guide. Before you begin the installation process, Ruckus Wireless
recommends that you become familiar with these features.
■ZoneFlex 2741 Access Point
■ZoneFlex 7762 Access Point
■ZoneFlex 7762-S Access Point
■ZoneFlex 7762-T Access Point
■ZoneFlex 7762-AC Access Point
■ZoneFlex 7762-S-AC Access Point
■ZoneFlex 7761-CM Access Point
NOTE: This User Guide does not include information on ZoneFlex Indoor Access
Points, ZoneFlex 7731 Wireless Bridge, or ZoneFlex 7025 Multimedia Wi-Fi Wall
Switch. For information on those ZoneFlex models (along with Ruckus Wireless
MediaFlex and MetroFlex product lines), refer to their respective documentation
available from support.ruckuswireless.com.

3
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
ZoneFlex 2741 Access Point
Figure 1 and Figure 2 identify the Access Point external features. Before you begin
the installation process, Ruckus Wireless recommends that you become familiar with
these features.
Figure 1. Access Point LEDs and bottom connectors
Table 3. LEDs and bottom panel connectors
No Label Description
1 LEDs See “LED Colors and What They Mean”below for more
information.
2 RJ45 LAN port that supports Power over Ethernet (PoE) and 10/
100Mbps network connections

4
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
LED Colors and What They Mean
Refer to Table 4 below for all possible LED states and what they indicate.
3 Reset Using a pointed object (for example, a pen), press this
button to restart the Access Point or to restore it to factory
default settings:
• To restart the Access Point, press the Reset button once.
• To restore the Access Point to factory default, press the
Reset button for six (6) seconds.
WARNING: Restoring the Access Point to factory default
settings removes all configuration changes that you have
made. These include the IP address, password, access
control list, and wireless settings. Returning the
configuration of these features to their factory default
settings may result in network connectivity issues.
4 12V DC In addition to PoE, you can also use direct current or DC
(from a battery, for example) to supply power to the Access
Point.
Table 4. LED states and behaviors
LED Meaning
OPT Not used in this model
DIR • Off: The Access Point is not being managed by
ZoneDirector (standalone mode).
•Green: The Access Point is being managed by
ZoneDirector.
•Flashing green: The Access Point is being managed
by ZoneDirector, but is currently unable to
communicate with ZoneDirector.
Table 3. LEDs and bottom panel connectors
No Label Description

5
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
AIR • Green: The Access Point is functioning as a mesh
AP (MAP) and the wireless signal to its uplink MAP
is good (> 24dbm).
•Fast flashing green (two flashes every second): The
Access Point is functioning as a mesh AP (MAP) and
the wireless signal to its uplink MAP is poor (<
24dbm).
•Slow flashing green (one flash every two seconds):
Mesh networking is enabled, but the Access Point
cannot find a mesh uplink.
•Off: The Access Point is operating in standalone
mode or, if mesh networking is enabled, the Access
Point is functioning as a root AP (RAP).
WLAN • Green: The wireless LAN (WLAN) service is up and
at least one wireless client is associated with it. If
mesh networking is enabled, there are no downlink
MAPs connected to this Access Point.
•Fast flashing green (two flashes every second): The
WLAN service is up and at least one wireless client
is associated with it. Mesh networking is enabled
and at least one downlink MAP is connected to this
Access Point.
•Slow flashing green (one flash every two seconds):
The WLAN service is up, but no wireless clients are
currently associated with it. Mesh networking is
enabled and at least one downlink MAP is
connected to this Access Point.
•Off: Either the WLAN is down, or it is up but no
wireless clients are currently associated with it. If
mesh networking is enabled, there are no downlink
MAPs connected to this Access Point.
LAN • Green: The LAN port is connected to a 10/100Mbps
device.
•Flashing green: Traffic is passing through the LAN
port.
•Off: The LAN port is not connected to any network
device.
PWR • Green: The Access Point is connected to a power
source.
•Off: No power is available, or the Access Point is not
connected to a power source.
Table 4. LED states and behaviors
LED Meaning

6
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
If you want to extend the range of your wireless network, you can connect an external
high gain antenna to the standard N-type radio frequency (RF) antenna connector on
the top panel of the Access Point. The antenna must have a gain of less than 9dBi to
comply with FCC and CE regulations.
Figure 2. The antenna connector is protected by a black waterproof antenna
connector cover

7
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
ZoneFlex 7762 Access Point
Figure 3 and Figure 4 identify the Access Point external features. Before you begin
the installation process, Ruckus Wireless recommends that you become familiar with
these features.
Figure 3. Access Point parts
Power LED Status LED
5GHz External
Antenna
Connectors
RJ-45/PoE
Connectors
DC Connector
Ground Screw

8
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
Table 5. LEDs and connectors on the AP
Label Description
Power LED •Off: No power is available, or the Access Point is not
connected to a power source.
•Red: The Access Point is powering on.
•Green: The Access Point is connected to a power source
and has completed its power-on sequence.
Status LED If the Access Point is operating in standalone mode:
•Amber: The WLAN service is up and at least one wireless
client is associated with the AP.
•Flashing amber: The WLAN service is up and no wireless
clients are currently associated with the AP.
If the Access Point is being managed by Ruckus Wireless
ZoneDirector:
•Green: The AP is part of a mesh network (either as Root
AP or Mesh AP) and is connected to an uplink with good
signal. If mesh networking is disabled but the WLAN
service is available, the Status LED is also green.
•Fast flashing green: The AP is part of a mesh network
(as Mesh AP) and is connected to an uplink with fair
signal.
•Slow flashing green: This Mesh AP is searching for an
uplink or is attempting to establish communication with
ZoneDirector.
•Off: Mesh networking is disabled and the WLAN service
is unavailable.
RJ45 Connectors Two LAN ports that support Power over Ethernet (PoE):
•PoE IN port: Supports 10/100/1000Mbps connections,
connects to the network and receives 802.at PoE from
the supplied PoE injector (if connected).
•PoE OUT port: Supports 10/100/1000Mbps
connections. If the supplied PoE injector is used, this
port can supply 802.af PoE to the connected PoE-
capable device (for example, another ZoneFlex 7762 AP
or an IP-based surveillance camera). To use this port to
supply PoE, you first need to enable the PoE feature on
the Web interface.
DC Connector In addition to PoE, you can also use direct current or DC
(from a battery, for example) to supply power to the Access
Point.

9
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
If you want to extend the range of your wireless network, you can connect external
high gain antennas (5GHz only) to the standard N-type radio frequency (RF) antenna
connectors on the top panel of the Access Point.
Figure 4. The 5GHz antenna connectors are protected by metal caps
ZoneFlex 7762-S Access Point
Figure 5 and Figure 6 identify the Access Point external features. Before you begin
the installation process, Ruckus Wireless recommends that you become familiar with
these features.
Metal caps

10
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
Figure 5. Access Point parts
Table 6. LEDs and connectors on the Access Point
Label Description
Power LED •Off: No power is available or the Access Point is not connected
to a power source.
•Red: The Access Point is powering on.
•Green: The Access Point is connected to a power source and
has completed its power-on sequence.
Power LED Status LED
RJ-45/PoE
Connectors
DC Connector
Ground Screw
PoE IN
PoE OUT
5GHz External
Antenna
Connectors

11
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
5GHz Antenna Connectors
If you want to enable the 5GHz sections of the AP (for access or meshing), you can
connect external high gain antennas (5GHz only) to the standard N-type radio
frequency (RF) antenna connectors on the top panel of the Access Point.
Status LED If the Access Point is operating in standalone mode:
•Amber: The WLAN service is up and at least one wireless client
is associated with the AP.
•Flashing amber: The WLAN service is up and no wireless clients
are currently associated with the AP.
If the Access Point is being managed by Ruckus Wireless
ZoneDirector:
•Green: The AP is part of a mesh network (either as a Root AP or
Mesh AP) and is connected to an uplink with good signal. If
mesh networking is disabled but the WLAN service is available,
the Status LED is also green.
•Fast flashing green: The AP is part of a mesh network (as Mesh
AP) and is connected to an uplink with a fair or good signal.
•Slow flashing green: This Mesh AP is searching for an uplink or
is attempting to establish communication with ZoneDirector.
•Off: Mesh networking is disabled and the WLAN service is
unavailable.
RJ45 Connectors Two LAN ports that support Power over Ethernet (PoE):
•PoE IN port: Supports 10/100/1000Mbps connections, connects
to the network and receives 802.at PoE from the supplied PoE
injector (if connected).
•PoE OUT port: Supports 10/100/1000Mbps connections. If the
supplied PoE injector is used, this port can supply 802.af PoE to
the connected PoE-capable device (for example, another
ZoneFlex 7762-S AP or an IP-based surveillance camera). To use
this port to supply PoE, you first need to enable the PoE feature
on the Web interface.
DC Connector In addition to PoE, you can also use direct current or DC (from a
battery, for example) to supply power to the Access Point.
NOTE: If you connect the Access Point to both PoE and DC power
sources at the same time, it will use PoE as the primary power
source and DC power as the backup power source.
Table 6. LEDs and connectors on the Access Point
Label Description
P

12
Introducing the ZoneFlex Access Point
Getting to Know the Access Point Features
Figure 6. The 5GHz antenna connectors are protected by metal caps
ZoneFlex 7762-T Access Point
Figure 7 and Figure 8 identify the Access Point external features. Before you begin
the installation process, Ruckus Wireless recommends that you become familiar with
these features.
Metal caps
Before you install the AP, make a
note of the MAC address on this
label. You will need it later.