Rukket BASKETBALL REBOUNDER User manual

Our video instructions provide the best guidance for setting up your Basketball Rebounder.
They can be viewed online at
Support Arms
Frame - Sides
Frame -Top/Bottom
Support Post -Top
Support Post - Bottom
Support Post Arms
Short Carriage Bolts (M8, 25mm)
PlasticTwist Handle
Long Carriage Bolts (M8, 70mm)
Small Hex Wrench
Large Hex Wrench
Wrench
Nuts
Small Hexagonal Screw (M6, 15mm)
Hexagonal Screw (M8, 20mm)
Small Metal Washers
Medium Metal Washers
Plastic Washers
Large Metal Washers
Long Carriage Bolts (M4.5, 20mm)
Bolts
Plunger Bolts
Bungees (25pcs)
Rebounder Net
Base with WaterTank
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
X.
Y.
A
C
B
B
C
D
E
O
P
Q
F
G
X
U
W
V
S
R
H
I
J
K
L
MN
T
Y
RUKKET BASKETBALL REBOUNDER
assembly INSTRUCTIONS

B
B
U
T
RUKKET BASKETBALL REBOUNDER
assembly INSTRUCTIONS
Net Frame Assembly
1
Use the hexagonal screws (4 x O), washers (8 x Q, 2 x S, and 4 x R), and nuts (4 x M) to attach the Support
Arm (A) to the Rebounder Net Frame.
Use the diagram in Figure 1 to complete the assembly. Do not over tighten the nuts for the time being for
the frame sides.
Assemble the frame using the 2 sides, top, and bottom frame pieces (2 x B & 2 x C) using 4 sets of carriage
bolts (4 x T and 4 x U). Use the provided hex wrench as shown in the diagram to tighten the carriage bolts.
Once the Support Arm is attached to the frame insert the plunger bolt apparatus (V) to each side of the
frame in the location depicted in Figure 1.
C
C
A
M4.5, 20mm
M8, 20mm
V.
M
O
Q
S
Q
R

RUKKET BASKETBALL REBOUNDER
assembly INSTRUCTIONS
Netting Assembly
2
Hang the netting(X) by passing the top crossbar
bungees(W) over the upper crossbar and
hooking them back onto the thick woven edge
of netting.

RUKKET BASKETBALL REBOUNDER
assembly INSTRUCTIONS

Base & Support Post
Insert the support frame and down tube, then screw and tighten the plastic twist handle. (Figure 2) Handle
with care to avoid scratching the paint on the iron pipe. Insert the lower tube with the support frame into
the water tank and tighten the screws. (Figure 3)
After xing the bracket and the water tank, insert the top tube to connect and tighten the two left and
right screws for reference. (Figure 4)
Guide the assembled red grid to the top tube and insert two screws to x it. The height of the grid can be
adjusted by loosening the two screws. (Figure 5)
Y
Y
Y
F
F
Y
M8, 70mm
M8, 25mm
M8, 20mm
N
M6, 15mm
M8, 70mm
E
H
I
G
HH
O
D
I
H
RUKKET BASKETBALL REBOUNDER
assembly INSTRUCTIONS
P
S
3

Keep hands and ngers clear of all moving parts,when adjusting the angle of the basketball rebounder using the rear
telescoping supports. Place the rebounder on a level,well drained surface.Make sure to set the rebounder up in a
location where,when a ball misses the rebounder or is missed by the player on its return,the ball will not strike or cause
damage to people, pets ,houses,or structures. Children should not operate the rebounder adjustment; Adjustment
should be made by an adult.To prevent injury,children should not use the rebounder until properly instructed.it is
important to become familiar with the way a ball reacts to the rebounder;stand at least 30 feet from the rebounder
when rst using it so you can became familiar with the speed and power of returned balls. Always check for loose or
missing bolts and for damage to the bungees or netting before use. Loose bolts should be tightened.If there is a
problem with the netting or any other part of the rebounder, please contact us at1-855-4RUKKET.
RUKKET BASKETBALL REBOUNDER
assembly INSTRUCTIONS
Warnings
Adjusting the Angle of the Rebounder
4
This rebounder comes standard with an easy to use angle adjuster. The angle can be
changed to practice dierent types of passses like chest passes and bounce passes.
With one hand, pull the plunger bolt cord and adjust the angle by moving the net frame
with the other hand. (Figure 6) To adjust the height of the rebounder use the included
hex wrench to remove the long carriage bolt and move the support post up or down.
Figure 6