Rukket SOFTBALL SOCK NET User manual

pipes together (Fig. A)
1. Join the two slightly bent
123
456
789
A
B
X
123
456
789
1. Join two straight Pipes
together. (Fig. A)
Then attach both end legs
(Fig. B)
A
B
123
A
B
1
A
23
B
2. Install two lower Black Rods
with Coupling Tubes up, into
angled Pipes.
3. Thread Sleeve over Black
Rod. Make sure logo is not
upside down.
4. Repeat with Sleeve pocket
over other Black Rod.
5. Take Black Rod and slide
into lower rod’s Coupling Tube.
6. Hold Black Rod while pulling
Sleeve up. Loop white cord
over rod top.
7. Take the last Black Rod and
slide into Rod Coupling Tube.
8. Grip Black Rod and pull
Sleeve up. Loop Cord over pole
top.
9. Take lower Elastic Loops and
place under stud on both end legs.
10. Wrap velcro around frame. (X
in Fig. 8)
X
Check out our video instructions at:
/RukketSports
1. Join two slightly bent
pipes together (Fig. A)
Then attach both end legs
(Fig. B)
3. Thread a fiberglass pole through one
of the net's sleeves making sure the net
is right side up (white loops at the top
corners and black bungees at the bottom
corners).
2. Install the two lower fiberglass
poles, with coupling tubes at the
top, into the angled pipes on the
metal base.
4. Repeat for the other side. 5. Insert an upper fiberglass pole into
one of the lower pole's coupling tube.
The metal knob should be at the top.
6. Gripping the assembled fiberglass
pole, slide the net's sleeve up the pole
and loop the white rope onto the metal
knob on top.
7. Insert the remaining upper fiberglass
pole into the remaining lower pole.
8. Grip the pole and slide the sleeve up
before looping the white rope around the
metal pole top.
9. Loop the black elastic bungees over
the metal posts located on the outside of
each end leg. 10. Wrap the velcro
around the frame (X in Fig. 8).
SOFTBALL SOCK NET
ASSEMBLY INSTRUCTIONS
QUESTIONS? GIVE US A CALL! (1-855)-478-5538
V1
RukketSports
Our video instructions provide the best guidance for setting up your Sock It! Baseball/Softball Net.
They can be viewed online at

11. Lay the target flat on the ground to
make it easier to untangle. Insert the
black hooks on the upper strike zone
straps into the red loops in the upper
corners of the net.
12. Attach the lower bungee loop from
the lower strike zone cords to the posts
at the base of both legs.
13. To adjust the height of the strike
zone target, slide the plastic adjusters
along the nylon tape up or down.
14. For a higher strike zone, use the
elastic loops at the end of the elastic
cords. For a lower strike zone, use the
elastic loops farther up the elastic cord.
15. The four inner ropes slide along the
strike zones edges.
16. Adjust the ropes any way you want
to create your own unique pitching
challenges!
WARNING
Please use adult supervision and follow the instructions when setting up and using this net. Regular use or abuse will eventually
strain the netting and may break it. Do not stand behind the net. This net is not intended for personal protection. This net deflects
fast moving objects, so people should be at least ten (10) feet away.
PRIOR TO USE
Inspect the netting and frame for damage or wear. Make sure the frame and net are assembled correctly and on a flat surface, at
least ten (10) feet away from structures and vehicles. The user should be positioned directly in front of the net. Failure to follow
these precautions could result in serious injury or damage to property.
QUESTIONS? GIVE US A CALL! (1-855)-478-5538
V1
SOFTBALL SOCK NET
ASSEMBLY INSTRUCTIONS