RUSTICA STAG HANGER User manual

STAG/
CLASSIC/
LOFT
HANGER
INSTALLATION
INSTRUCTIONS
FOR
FLAT TRACK
CONGRATULATIONS ON YOUR DECISION TO BRING HOME AN
AMERICAN MADE PRODUCT OF THE HIGHEST QUALITY.
1-800-891-8312
[email protected]
www.Rustica.com
DESIGNED AND CRAFTED ENTIRELY IN THE
U.S.A.
DON’T BE A STRANGER.
FOLLOW US ON SOCIAL MEDIA.

2
www.Rustica.com
NOTE:
or fla
PARTS
H.
5 8

3www.Rustica.com
45"()"/(&3"TTFNCMZ*OTUSVDUJPOT
NOTE:
%PPSTVTJOH'MPPS.PVOU%PPS(VJEFTXJMMIBWF
BHSPPWFPOUIFCPUUPN&OTVSFUIJTHSPPWFJTPO
UIFPQQPTJUFFOEPGUIF%PPS)BOHFS*OTUBMMBUJPO
HANGER INSTALLATION
 -BZUIFEPPSXJUIUIFGSont facing up on a flaUMFWFMTVSGBDF
 1MBDFUIFIBOHFSPOUIFEPPS'JHVSF
 "EKVTUUIFQMBDFNFOUPGUIFIBOHFSGPSBŐHBQCFUXFFOUIFUPQPGUIFEPPSBOEUIFCPUUPNFEHFPG
UIFXIFFM&OTVSFUIFTJEFPGUIFIBOHFSJTSFTUJOHŐGSPNUIFFEHFPGUIFEPPS'JHVSF
 .BSLUIFDFOUFSPGFBDIJOTUBMMBUJPOIPMFXJUIBQFODJM'JHVSF
 3FQFBUTUFQTGPSUIFPQQPTJUFFOEPGUIFEPPS4FUUIFIBOHFSTBTJEF
 %SJMMUXPQJMPUIPMFTBMMUIFXBZUISPVHIUIFEPPSGPSFBDIIBOHFSVTJOHBESJMM
XJUIBOŐESJMMCJU'JHVSF
 5VSOUIFEPPSPWFS6TJOHBŐ'PSTUOFSCJUESJMMBŐEFFQIPMFJOUP
FBDIQJMPUIPMF'JHVSF
 5VSOUIFEPPSPWFSSFUVSOJOHJUUPUIFGBDFVQQPTJUJPO%SJMMBMMUIFXBZUISPVHIUIFQJMPUIPMFTVTJOHBESJMM
XJUIBŐESJMMCJU'JHVSF
 *OTUBMMUIFIBOHFSTUPUIFGSPOUPGUIFEPPSVTJOHMBHCPMUTXBTIFSTBOEBDPSOOVUTQSovided) (figurF
"Ő4QBEFCJUNBZCFVTFEJOQBDFPGB'PSTUOFSCJU
'JHVSF 'JHVSF
'JHVSF 'JHVSF 'JHVSF
'JHVSF
%PPS'SPOU %PPS#BDL Door Fron %PPS'SPOU
Ő
*OTUBMMBUJPO
)PMFT
Ő
Ő

Use teamwork. We recommend two people for this build.
FIRST THINGS FIRST
Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide XFMM If the floor is
not level, measure from the highest point of the floor surface to the NBLFTVSFUIFEPPSDMFBSTUIFGMPPS
Ensure the track will be installed onto wall studs or in wall blocking. If wall studs are not lining up with the installation a header will be
required to provide the necessary strength and stability for the track and door.
Figure 2
1. To determine where the track should be installed, first measure
the height of the door, then add 2-1/8” to the door height. 1/2” (a)
will be for the clearance between the bottom edge of the door
and the floor. 1-5/8” (b) will be from the top edge of the door to
the center of the track. (Figure 1).
2. Using a level and a pencil, make a line on the wall at this height. It
will be the centerline of the track.
3. Hold the track up to where the pencil line is visible through the
holes in the track (Figure 2).
4. Mark an intersecting line in the center of each hole (Figure 2).
5. Take the track down, drill out the marked holes using a drill with a
1/4” drill bit (Figure 3).
6. Attach one end of the track to the wall with one standard stop,
one lag screw, and one washer, using a socket wrench with 9/16”
socket (Figure 4). Do not tighten.
7. Repeat step 7 for the other end of the track.
8. Attach the rubber bumper to the inside of the standard stop.
Repeat for the hard stop on the other end of the track (Figure 4a).
9. Install remaining spacers with lag screws and washers using a
9/16” socket wrench (Figure 5). Tighten all lag screws.
10. Hang the door (Figure 6).
DOOR GUIDE INSTALLATION
11. With the door in the closed position, ensure the door is hanging
straight using a bubble level.
12. Position the Door Guide part way into the groove in the bottom of
the door (Figure 7).
13. Install the Door Guide using a 1” phillips screw
(provided) and a drill with a phillips bit.
14. Slide the door toward the open position until the other side of the
Door Guide is exposed.
15. Install the second 1” phillips screw (provided) using a drill with a
phillips bit (Figure 8).
ANTI-JUMP GUIDE INSTALLATION
16. Place the Anti-Jump bracket on the door side, moving the bracket
up until it is between 1/8” and 1/16” from the bottom edge of the
rail. Mark the placement with a pencil.*
17. Install the bracket to the door edge with 2 phillips screws
(provided) using a drill with a phillips bit
(Figure 9).
18. Repeat steps 17 and 18 for the opposite end of the door.
19. Place the Anti-Jump block on the top of the door (Figure 10).
Using a drill with a phllips bit, install the the block with the 1”
phillips screw (provided).
20. Repeat steps 20 for the opposite end of the door.
1-5/8” b
1/2” a
Door
Height
Figure 3
Figure 1
Figure 4
Figure 5
Figure 4a

Figure 6
Figure 7 Figure 8
Figure 10
Figure 9
FLAT TRACK "TTFNCMZ*OTUSVDUJPOT
4www.Rustica.com