RUTEC VARDAflex Quantum Triple User manual

Quantum Tr ple
Der LED-Strip ist nur für die Installation in tro ckenen
Innenr umen geeignet.
Stromschlaggefahr!
Beauftragen Sie mit der Installation eine Elektrofach kraft.
Für Leuchten, die nicht gem ß den euro p ischen
Sicherheitsrichtlinien installiert wurden, entf llt jeder
Haftungsanspruch.
Achtung!
LED-Strip nur an geeignetes Netzger t
(24 V DC) anschließen.
Nur komplett abgerollt betreiben.
LED-Strips in Parallelschaltung verbinden.
L eferumfang
1 x 5 Meter LED-Strip
Techn sche Daten
Spannungsversorgung 24 V Netzger t mit konstanter
Ausgangsspannung
Leistung 115 W
Stromst rke 4,8 A
Ausstrahlwinkel 120°
Anzahl LED 1120
L nge Maximal 5 Meter pro Anschluss
Abmessungen 5000 x 10 x 1,4 mm
Biegedurchmesser 40 mm
CE-konform mit den zutreffenden
europ ischen Richtlinien
Schutzklasse 3 - Schutzkleinspannung
Sehr hell - Profil notwendig
LED-Strip nicht ohne
weiteren Kühlkörper sowie ausreichende
Belüftung betreiben
Nur für den Innenbereich geeignet
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Montage
Stromschlaggefahr!
Vor der Installation Spannung abschalten. Sicherstellen, dass
die Spannung nicht versehentlich wieder eingeschaltet werden
kann.
Achtung!
Bei stromführenden Oberfl chen Isolierschicht zwischen
LED-Strip und Oberfl che anbringen. Ober -
fl chen müssen eben, staub- und fettfrei sowie trocken sein.
1. Oberfl che vorbereiten.
2. LED-Strip, falls erforderlich, kürzen (Bild 1).
3. Schutzfolie abziehen und LED-Strip mit leichtem
Druck anpressen, dabei nicht direkt auf die elektronischen
Bauteile drücken.
4.
LED-Strip an Spannungsversorgung anschließen.
LED-Plat ne kürzen
Stromschlaggefahr!
Vor dem Kürzen immer spannungsfrei schalten.
LED-Strip kann jeweils nach acht LEDs
(35,7 mm) getrennt werden (Bild 1).
LED-Strip an der markierten Stelle trennen.
Bei eng bestückten LED-Strips wird ein Mikroseitenschneider
oder optional ein Cutter benötigt
!
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
DD
B ld 1
Be sp elabb ldung
Achtung!
Bei Lötverbindungen beachten: Löttemperatur 260° C und
Lötdauer maximal 10 Sekunden.
Es ist ausschließlich neutral vernetztes Silikon zu verwenden
(keinesfalls essighaltiges Silikon verwenden!).
Entsorgung
Entsorgen Sie elektrische und elektronische Ger te umweltge-
recht. N here Informationen erhalten Sie bei Ihrer zust ndigen
Behörde.
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Carl-Zeiss-Str. 15
28857 Syke
QuantumTriple_BA_84115ff_04/2018

Quantum Tr ple
The LED strip is only suitable for installation in dry
indoor rooms.
R sk of electr c shock!
Be sure to have a professional electrician complete
in stallation. There is no warranty coverage for any lights
installed without observing european safety directives.
Caut on!
Only connect the LED strip to a suitable
power supply (24 V DC).
Only operate when completely unrolled.
Connect LED strips in parallel.
Del very ncludes
1 x 5 metre LED strip
Techn cal data
Power supply 24 V power supply with constant
output voltage
Power 115 W
Current strength 4,8 A
Radiation angle 120°
Quantity LED 1120
Length maximum 5 metres per connection
Dimensions 5000 x 10 x 1,4 mm
Bending diameter 40 mm
Compliant with the applicable
european CE directives
Safety class 3 - low voltage protection
Very light - profile necessary
The LED strip needs an
additional cooling element and
sufficing air ventilation.
Suitable for indoor use only
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
GG
F gure 2
example f gure
Carl-Zeiss-Str. 15
28857 Syke
Installat on
R sk of electr c shock!
Switch off voltage prior to installation. Ensure that voltage
cannot be accidentally switched on again.
Caut on!
On conducting surfaces, place an insulation layer between the
LED strip and surface. Surfaces must be flat, free
of dust, grease and dry.
1. Prepare surface.
2. Shorten LED strip if necessary (Fig. 1).
3. Peel off adhesive film and gently press on
LED strip, do not press directly on the LEDs.
4. Connect
LED strip to power supply.
Shorten ng the LED str p
R sk of electr c shock!
Always disconnect the mains plug before shortening.
LED strip can be separated in each case after
e ght LEDs (35,7 mm) (Fig. 1).
Separate the LED strip at the marked position.
For a tightly assembled LED strip is a micro side cutter or an
optional cutter required.
Caut on!
With soldered connections note that the soldering
tem perature is 260° C and the soldering duration a
maximum of 10 seconds per soldering point.
Only use neutral cross-linked silicon (never use silicon which
includes vinegar!).
D sposal
Dispose of electrical and electronic equipment in an
environmentally friendly manner. Please contact your local
council for further information.
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
QuantumTriple_BA_84115ff_04/2018